ページ1に含まれる内容の要旨
OWNER’S MANUAL
INSTALLATION INSTRUCTIONS
®
WINEGARD
RV Digital Satellite System
with RS-1000 Antenna
Model RD-4610
U.S. PATENTS 5,532,710
and 5,554,998
Made in U.S.A.
IMPORTANT:
INSTALL POINT
OF BASE
TOWARD FRONT
OF VEHICLE!
Winegard Company • 3000 Kirkwood St. • Burlington, IA 52601-2000
319/754-0600 • FAX 319/754-0787
Printed in U.S.A. ©Winegard Company 2001 2451142 Rev. 6/05/01
ページ2に含まれる内容の要旨
INSTALLATION & ASSEMBLY STEP 1. Choose a location for antenna that will allow it to rest in travel position with antenna pointing toward rear of vehicle and raise and rotate without interfering with other roof-mounted equipment. Make sure inside ceiling area is clear where ceiling plate will mount. NOTE: Figure 1 shows minimum distance (10") antenna should be located from edge of vehicle roof. We recommend you check with your dealer or the manufacturer to see what provisions have been made in
ページ3に含まれる内容の要旨
STEP 3. Attach reflector to backup assembly as shown in Figure 2. STEP 4. Attach RS-1000 antenna to elevating tubes, see Figure 2, using the two Eclips and pins provided. Attach coax cable to F-jack on antenna, slide weather boot over boot collar. RS-1000 Antenna Reflector Attach coax cable to (4) 5/16-18 x 5/8" F-jack on antenna, Flat Head Bolt slide weather boot over boot collar. Attach RS-1000 to elevating tubes using E-clips and pins supplied. (4) 5/16-18 Hex Nut Backup Assembly (4) 5/16"
ページ4に含まれる内容の要旨
STEP 5. The mount is designed to fit roofs 1" to 4 3/4" thick. If roof is less than 4 3/4" thick, cut elevating shft and directional handle to size. (See table below.) If roof is more than 4 3/4" thick, the RP-2000 Thick Roof Kit is required. See page 15, A for chart. CAUTION: IF YOU ARE USING THE RW-1000 ROOF WEDGE, ADD 1/2" TO ELEVATING SHAFT LENGTH GIVEN BELOW, BUT NOT TO THE DIRECTIONAL HANDLE. Direc- tional Handle ROOF ELEVATING SHAFT W/RW-1000 DIRECTIONAL THICKNESS LENGTH HANDLE LENGTH 4 3
ページ5に含まれる内容の要旨
Cable clamp on gear housing. CAUTION: DO NOT GET SEALING COMPOUND ON BEARING SURFACE BETWEEN BASE PLATE AND ROTATING GEAR HOUSING. DO NOT PAINT TOP OF BASE PLATE OR AROUND ROTATING Cable Ties GEAR HOUSING. NOTE: Apply sealant approved for your vehicle roof between Base Plate and roof of vehicle. 3" min. FIGURE 3 #10 x 1" Screws Attach cable clamp here. Make sure there are 16" of coax between the cable clamp on the gear housing and the one here 3" in front of base plate. TOO MUCH OR TOO LITT
ページ6に含まれる内容の要旨
CAUTION: After INITIAL FIGURE 4 INSTALLATION, 1 Ceiling Base the antenna SHOULD ROTATE APPROXIMATELY 360 DEGREES FROM TRAVEL POSITION. The pointer on the POINT TO DIRECTIONAL HANDLE FRONT OF RV should point towards the ROTATION CLAMP when in TRAVEL POSITION. ASSEMBLED VIEW 3 Directional Handle Extension 2 (4) #10 Phillips Flat Head Screws 4 Directional Handle ALIGN POINTER WITH ANTENNA TRAVEL POSITION 5 ELEVATING CRANK HANDLE (When installed, extends 2-1/4" from ceiling). Snap Handle into base
ページ7に含まれる内容の要旨
OPERATION STEP 1. Using a compass, determine which direction is North. It is recommended that you step outside to perform this step. Standing in or near coach/RV can give you an incorrect reading. The more accurately you determine North, the easier it will be to find the satellite(s). Directional Handle Elevating Crank Directional Handle Directional Dial Pointer FIGURE 5 Rotation Clamp STEP 2. Move rotation clamp to the LOCK position. STEP 3. Rotate directional dial (see Figure 5) until the
ページ8に含まれる内容の要旨
TUNING ANTENNA FOR BEST PICTURE STEP 8. Your receiver should indicate it is receiving a signal. To tune your antenna for the best picture, slowly move the antenna left, then right until you have found the position that gives the highest signal strength. It is important to turn the antenna slowly; since the signal is digital the receiver takes a few seconds to lock on. STEP 9. Place rotation clamp in the LOCK position. This prevents the antenna from moving and losing the signal. STEP 10. Slowly
ページ9に含まれる内容の要旨
Coax downlead Coax from satellite downlead antenna from RS-1000 TV Satellite Receiver Power Supply VCR A-B Switch FIGURE 6 Coax downlead Coax from satellite downlead antenna from RS-1000 TV Satellite Receiver Power Supply Video Switch VCR Set 2 FIGURE 7 Coax downlead Coax downlead from satellite from RS-1000 antenna TV Satellite Receiver Power Supply VCR 9 FIGURE 8
ページ10に含まれる内容の要旨
MAINTENANCE MOUNT LUBRICATION To lubricate the mount, apply a liberal amount of silicone spray lubricant to the elevating gear, the lubricant hole and between the gear housing and baseplate. Run the antenna up/down and rotate the antenna to distribute the lubricant. See Figure 9. Remove cap and spray Spray lubricant lubricant into the here on elevation gear lubricate hole. Be sure place cap firmly back on. Spray lubricant around edges FIGURE 9 LUBRICATING RUBBER QUAD RING Lubricate rubber qu
ページ11に含まれる内容の要旨
TROUBLE SHOOTING NO PICTURE 1. Check that you have a clear line of sight to the satellite (no trees, buildings, etc.). 2. Check that you have the TV set tuned for the correct channel 3 or 4 (same channel as output of receiver). 3. Double check that you have entered the correct zip code into the receiver. If zip code is wrong, this can cause you to look in the wrong direction/elevation for the satellite. 4. Check connections at receiver, TV, and antenna. 5. Check TV. Does it receive pic
ページ12に含まれる内容の要旨
PARTS LIST (not all parts listed 46cm (18") Reflector, White due to space constraints) P.N. 2745304 (4) 5/16" Hex Nut P.N. 2160230 (4) 5/16" Flat Washer P.N. 2160027 (2) 1/4-20 Hex Nut, Nylock P.N. 2160220 (4) 1/4" Flat Washer Backup P.N. 2160039 (5) E-Clip P.N. 2745348 P.N. 5160818 (2) 1/4-20 X 1.75" Hex Bolt P.N. 2160238 Digital Elevation (3) 1/4 x 2-5/16" Pin Device, If attached P.N. 2160814 the 1/4-20 x 1.75 Hex Bolts are replaced Bumper Assembly with 1/4-20 x 2" Hex P.N. 3750823 Bolts (2
ページ13に含まれる内容の要旨
PARTS LIST Upper Elevating Tub P.N. 3506032 RS-1000 Mount Adapter P.N. 2200114 Bolt Lower Elevating Tube P.N. 3200350 P.N. 3506033 LNBF is attached to pivot arm with: 1/4-20 x 1/2" Cap Screw P.N. 2160240 LNBF 1/4-20 Nylock Hex Nut P.N. 2780161 P.N. 2160220 (2) 1/4" Washer P.N. 2160024 (4) Flat Head Bolts (white) P.N. 2160361 (3) 1/4 x 2-5/16" Pin P.N. 2160814 (2) Travel Link P.N. 2745050 LNBF Pivot Arm P.N. 2745059 Spring P.N. 2160820 (not shown for clarity) Fixed Feed Arm (4) Nylon Bearing P.N.
ページ14に含まれる内容の要旨
PARTS LIST INTERIOR HARDWARE KIT RK-CEIL Ceiling Base Directional Dial (4) #10 Phillip Flat Head Screws Azimuth Lock Azimuth Lock Knob Directional Handle Washer Extension #10 x 3/8" Phillips Directional Handle CRANK HANDLE KIT RK-HAND #8-32 x 3/8" Phillips Screw Crank Handle Base #8-32 Square Nut Crank Handle Knob #10 x 3/8" Phillips Screw Washer NOT TO SCALE Rev 6/05/01 14
ページ15に含まれる内容の要旨
SPECIFICATIONS Height when raised 37" max. Height in the travel position 12.0" max. Operating radius 17" (34" diameter circle) Roof space required 19.5" x 46.75" ® TM LNB Compatible with DSS and DISH Network Color White Satellite antenna height 20.9" Satellite antenna width 19.5" F/D 0.59 o Offset angle 24 Frequency range 10.95 - 12.75 GHz Satellite antenna gain: 11.2 GHz 33.22 dBi 12.1 GHz 33.89 dBi 12.6 GHz 34.23 dBi Aperture efficiency 73% Cross polarization (on axis) -21 dB o *Beamwidth at
ページ16に含まれる内容の要旨
Rev. 8-97
