ページ3に含まれる内容の要旨
Table of Content SAFETY ....................................................................................................................................................... 4-9 GENERAL SAFETY RULES ............................................................................................................ 4-9 FUNCTIONAL DESCRIPTION ..................................................................................................................... 10-11 MODEL..................................
ページ4に含まれる内容の要旨
Safety RECOGNIZE SAFETY INFORMATION This is the safety alert symbol. When you see this symbol on your tool or in this manual, be alert to the potential for personal injury. Follow recommended precautions and safe operating practices. UNDERSTAND SIGNAL WORDS A "DANGER, WARNING or CAUTION" safety warning will be surrounded by a "SAFETY ALERT BOX." This box is used to designate and emphasize Safety Warnings that must be followed when operating this tool. Accompanying the Safety Warnings are "signa
ページ5に含まれる内容の要旨
WARNING ALWAYS KEEP GUARDS IN PLACE and in working order. ALWAYS KEEP WORK AREA CLEAN Avoid injuries by not cluttering the work areas and work benches. NEVER USE TOOL IN HAZARDOUS ENVIRONMENTS Never use the power tool in damp or wet places and never expose it to rain. Always keep the work area well lighted. NEVER PERMIT CHILDREN OR OTHERS TO LOITER NEAR THE WORK AREA Keep all people (especially children) away from the work area. Always unplug unattended tools and keep the work place tamper-proo
ページ6に含まれる内容の要旨
WARNING FOR YOUR OWN SAFETY READ THIS INSTRUCTION MANUAL BEFORE OPERATING THE COMPOUND MITER SAW 1. Always wear eye protection when using the compound miter saw. 2. Always keep hands out of the path of the saw blade. 3. Never operate the saw without the guards in place. 4. Never perform any freehand operation with the compound miter saw. 5. Never reach around the saw blade. 6. Always turn off tool and wait for saw blade to stop before moving workpiece or changing settings. 7. Always disconnect p
ページ7に含まれる内容の要旨
CAUTION POLARIZED PLUGS To reduce the risk of electric shock, this equipment has a polarized plug (one blade is wider than the other). This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet. Do not change the plug in any way. EXTENSION CORD Make sure your extension cord is in good condition. When using an extension cord, be sure to use one he
ページ8に含まれる内容の要旨
IMPORTANT SPECIFIC SAFETY RULES FOR USE OF THIS POWER TOOL WARNING: THE FOLLOWING SPECIFIC OPERATING INSTRUCTIONS MUST BE OBSERVED WHEN USING THIS POWER TOOL IN ORDER TO AVOID INJURY. DO's: ALWAYS OBSERVE THE FOLLOWING RULES TO ASSURE SAFE USE OF THIS TOOL: 1. Review the Manual and familiarize yourself with the safety rules and operatinginstructions for this POWER TOOL before attempting to use it. 2. Always confirm that the POWER TOOL is clean before using it. 3. Always wear snug-fitting clothin
ページ9に含まれる内容の要旨
IMPORTANT SPECIFIC SAFETY RULES FOR USE OF THIS POWER TOOL WARNING: THE FOLLOWING SPECIFIC OPERATING INSTRUCTIONS MUST BE OBSERVED WHEN USING THIS POWER TOOL IN ORDER TO AVOID INJURY. DON'Ts: NEVER VIOLATE THE FOLLOWING RULES TO ASSURE SAFE USE OF THIS TOOL: 1. Never operate the POWER TOOL unless you fully understand the operating instructions contained in this Manual. 2. Never leave the POWER TOOL unattended without first unplugging the power cord. 3. Never operate the POWER TOOL when you are t
ページ10に含まれる内容の要旨
Functional Description MODEL: ET-3403-J 10-INCH COMPOUND MITER SAW NOTE: The information contained in this Instruction Manual is designed to assist you in the safe operation and maintenance of the power tool. NEVER operate, or attempt any maintenance on the tool unless you have first read and understood all safety instructions contained in this manual. Some illustrations in this Instruction Manual may show details or attachments that differ from those on your own power tool. NAME OF PARTS: (Fig.
ページ11に含まれる内容の要旨
Functional Description SPECIFICATIONS: COMPOUND MITER SAW ET-3403-J: Motor Series Commutator Motor Power Source Single-Phase AC 60Hz Voltage (Volts) 115 Full-load Current (Amp) 15 Applicable saw blade Outside Dia. 10" (255 mm) Hole Dia. 5/8" (15.9 mm) -1 No load speed 4900 min Max. sawing deminsions: Bevel 0°: Miter 0° Max. Height 2-1/4" (59 mm) (Max. Height 3-1/2" (89 mm) Max. Width 5-5/8" (144 mm) (Max. Width 3-7/8" (101 mm) Miter 45° Max. Height 2-1/4" (59 mm) (Max. Height 3-1/2" (89 mm) Max.
ページ12に含まれる内容の要旨
Preparation PREPARATION: Make the following preparations before operating the power tool: 1. Installation: Attach the power tool to a level, horizontal work bench in accordance with Fig. 3. Select 5/16" (8 mm) diameter bolts suitable in length for the thickness of the work bench. For example, use 2" (50 mm) or larger bolts for 1" (25 mm) thick work bench. The holder attached to the rear of the base helps stabilize the power tool. 2. Releasing the locking pin: When the power tool is prepared fo
ページ13に含まれる内容の要旨
Operation APPLICATIONS: Wood, plywood, color board, soft fabric board, hard board similar materials and aluminum sash. PRE-OPERATION: 1. Make sure that the power source is appropriate for the tool. WARNING: NEVER CONNECT THE POWER TOOL UNLESS THE AVAILABLE AC POWER SOURCE IS OF THE SAME VOLTAGE IS THAT SPECIFIED ON THE NAMEPLATE OF THE TOOL. NEVER CONNECT THIS POWER TOOL TO A DC POWER SOURCE. 2. Make sure the trigger switch is turned OFF. WARNING: IF THE POWER CORD IS CONNECTED TO THE POWER SOU
ページ14に含まれる内容の要旨
Operation PRE-OPERATION (CONTINUED): BEFORE CUTTING: 1. Cutting groove on the table insert: A groove has to be cut in the table insert, before starting operation. Secure a piece of wood about 5-1/2" (140 mm) wide to the table with the vise assembly, to prevent the breakage of the table insert. After the switch has been turned on and the saw blade has reached maximum speed, slowly lower the handle to cut a groove on the table insert. CAUTION: DO NOT CUT THE GROOVE TOO QUICKLY, OTHERWISE THE TABL
ページ15に含まれる内容の要旨
Operation PRE-OPERATION (CONTINUED): 4. Oblique angle: Before the power tool is shipped from the factory, it is adjusted for 0° and left 45° bevel cutting angles. The positioning and bevel cutting angle can be adjusted by changing the height of the 8 mm bolt. (Maximum bevel cutting angle is 45°). (Fig. 10) (Fig. 9) 5. Securing the workpiece: WARNING: ALWAYS CLAMP OR VISE, TO SECURE THE WORKPIECE TO THE FENCE; OTHERWISE THE WORKPIECE MIGHT BE THRUST FROM THE TABLE AND CAUSE BODILY HARM. 6. Insta
ページ16に含まれる内容の要旨
Operation OPERATION: WARNING: TO AVOID PERSONAL INJURY, NEVER REMOVE OR PLACE A WORKPIECE ON THE TABLE WHILE THE TOOL IS BEING OPERATED. NEVER PLACE YOUR LIMBS INSIDE OF THE LINE NEXT TO WARNING SIGN WHILE THE TOOL IS BEING OPERATED. THIS MAY CAUSE HAZARDOUS CONDITIONS (SEE FIG. 13). (Fig. 13) 1. Switch operation: The trigger switch lock-off button is designed to prevent inadvertent operation of the power tool. To operate the power tool, it is necessary to first fully insert the lock-off butto
ページ17に含まれる内容の要旨
Operation OPERATION (CONTINUED): 2. Using the vise assembly (Standard accessory): a. The vise assembly can be mounted on either the left fence {Fence (B)} or the right fence {Fence (A)} by loosening the 6 mm wing bolt (A). b. The screw holder can be raised or lowered according to the height of the workpiece by loosening the 6 mm wing bolt (B). After the adjustment, firmly tighten the 6 mm wing bolt (B) and fix the screw holder. c. Turn the upper knob and securely fix the workpiece in position (
ページ18に含まれる内容の要旨
Operation OPERATION (CONTINUED): 4. Miter cutting procedures: a. Loosen the side handle. b. Adjust the table until the indicator aligns with the desired setting on the miter angle scale as shown in Fig. 17. c. Retighten the side handle to secure the table in the desired position. CAUTION: NEVER REMOVE THE SIDE HANDLE; USE OF THE TOOL WITHOUT IT WOULD BE HAZARDOUS. TO PREVENT AN ACCIDENT OR PERSONAL INJURY ALWAYS FIRMLY TIGHTEN THE MITER HANDLE. NOTE: Positive stops are provided at the right and
ページ19に含まれる内容の要旨
Operation OPERATION (CONTINUED): 7. Crown molding cutting procedures: Fig. 20 shows two common crown molding types having angles of (0) 38° and 45°. For the typical crown molding fittings, see Fig. 20. (Fig. 19) (Fig. 20) The table below shows the miter angle and the bevel angle settings that are ideal for the two crown molding types. NOTE: For convenience, positive stops are provided for the miter setting (left and right 31.6°, 35.3°) positions. For miter cut setting If the table has been set t
ページ20に含まれる内容の要旨
Operation OPERATION (CONTINUED): Setting to cut crown moldings at positions (1) and (4) in Fig. 20 (see Fig. 21): 1. Turn the table to the right and set the Miter Angle as follows: *For 45° type crown moldings: 35.3° ( mark) *For 38° type crown moldings: 31.6° ( mark) 2. Tilt the head to the left and set the Bevel Angle as follows: *For 45° type crown moldings: 30° *For 38° type crown moldings: 33.9° ( mark) (Fig. 21) 3. Position the crown molding so that the upper surface ((A) in Fig. 19)
ページ1に含まれる内容の要旨
ET-3403-J 10-INCH
COMPOUND MITER SAW
CAUTION
RISK OF INJURY!
READ MANUAL BEFORE OPERATING!
THIS MANUAL IS AN IMPORTANT PART OF THE MITER SAW
AND SHOULD REMAIN WITH THIS UNIT WHEN YOU SELL OR RENT IT.
10-Inch Compound Miter Saw Operator's Manual 1
ページ2に含まれる内容の要旨
Introduction Congratulations on the purchase of your new Compound Miter Saw! You can be assured your compound miter saw was constructed and designed with quality and performance in mind. Each component has been rigorously tested to ensure the highest level of acceptance. This operator's manual was compiled for your benefit. By reading and following the simple safety, installation, opera- tion, maintenance and troubleshooting steps described in this manual, you will receive years of trouble-fr
