ページ1に含まれる内容の要旨
5.5 Amp Orbital Jigsaw with Laser
Item# 5926-06
Model # MIQ-FE-65
PLEASE READ AND SAVE ALL INSTRUCTIONS TO ENSURE THE SAFE AND
EFFECTIVE USE OF THIS TOOL.
ページ2に含まれる内容の要旨
TABLE OF CONTENTS Table of Contents P.1 Important Safety Instructions P. 2 Rules for Safe Operation P.3 General Safety Rules P.4-5 List of Main Parts, Technical Specifications, P.6 Contents of Packaging Adjustments, Inserting and Removing Saw P.7 Blades Operation P.8-10 Maintenance and Service Center P.10 Warranty Information P. 11 Warranty Card P.12 1
ページ3に含まれる内容の要旨
IMPORTANT SAFETY INSTRUCTIONS PLEASE READ AND SAVE THESE INSTRUCTIONS CAREFULLY TO ENSURE THE SAFE AND EFFECTIVE USE OF THIS TOOL. Safe operation of this power tool requires that you read and understand this operators manual and all labels affixed to the tool. Safety is a combination of common sense, staying alert, and knowing how your Jigsaw works. 1. Always hold tool by gripping surface when operating power tool. WARNING: Be aware when cutting into a surface that may have hidde
ページ4に含まれる内容の要旨
RULES FOR SAFE OPERATION SAVE THESE INSTRUCTIONS WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • Lead from lead-based paints, • Crystalline silica from bricks and cement and other masonry products, and • Arsenic and chromium from chemically-treated lumber. Your risk from these exposures varies, dependin
ページ5に含まれる内容の要旨
GENERAL SAFETY RULES WARNING! Read, understand and save all instructions. Failure to follow all instructions listed below may result in electric shock, fire or serious personal injury. The warnings, cautions, and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and caution are a factor which cannot be built into this product, but must be supplied by the operator.
ページ6に含まれる内容の要旨
5. Do not overreach. Keep proper footing and balance at all times. Proper footing and balance enables better control of the tool in unexpected situations. 6. Use safety equipment. Always wear eye protection. Dust mask, non-skid safety appropriate conditions. shoes, hard hat, or hearing protection must be used for LASER SAFETY 1. This tool emits laser radiation. Avoid direct eye exposure of any kind. Do not stare directly at the laser beam, or project beam into eyes of others. 2. L
ページ7に含まれる内容の要旨
LIST OF MAIN PARTS 1. Rocker Switch for Laser Guide 2. On/Off Trigger Switch 3. Locking Button 4. Dust Output /Vacuum Adapter 5. Hex Key Storage 6. Cutting Mode Selector 7. Guide Plate 8. Safety Guard 9. Laser Guide 10. Laser Battery Compartment TECHNICAL SPECIFICATIONS: Item Number 5926-06 Model Number MIQ-FE-65 Laser Specifications: Rating Voltage 120 VAC Class II Laser Product Frequency 60Hz Rating Voltage 3 VDC Amp 5.5A Average Power <1.0Mw No load speed 500
ページ8に含まれる内容の要旨
ADJUSTMENTS Inserting and Removing Saw Blades The following is a guide for installation and removal of saw blade. Warning: Before installing or changing a blade, be sure the saw is unplugged from the power supply. 1. Loosen the two blade lock bolts (use hex key supplied) enough for a blade to be removed or inserted. Fig. 1 2. Insert blade in slot with teeth facing forward. The blade’s top should be inserted far enough to touch blade clip. Fig. 2 3. While blad
ページ9に含まれる内容の要旨
OPERATION How to Start Jigsaw 1. Before you start make sure your saw blade and guard is secure. 2. Plug cord into power outlet. 3. Place saw near cutting surface. Make sure saw blade is down. 4. Position Speed Adjust Dial to desired stroke rate. 5. To start saw, press and hold the On/Off trigger switch. 6. To stop saw, release the On/Off trigger switch than remove saw from cutting surface. General Cutting Hold your saw firmly in front and clearly away from you. Make sure s
ページ10に含まれる内容の要旨
Bevel Cutting Warning: Before adjusting the cutting angles, be sure the saw is unplugged from the power supply. The base plate can be tilted to cut any angle between 0 and 45 degrees right and left. Loosen the base plate adjustment screw and then rotate the base plate left or right to the desired angle. Tighten the base plate adjustment screw to secure base plate. Fig. 5 Note: The base plate has a scale for setting 0 to 45 degrees. Use a protrac
ページ11に含まれる内容の要旨
Laser Guide Line The saw is equipped with a battery powered laser guide which is designed to aid alignment of the blade with your cutting line. Push the rocker switch located on the battery compartment cover of the laser guide to turn it On or Off. To replace the batteries, pull the upper part of the battery compartment cover up and then slide the lower part of the battery compartment cover away from the compartment.
ページ12に含まれる内容の要旨
WARRANTY INFORMATION LIMITED WARRANTY Thank you for purchasing a top quality KingCraft product. This Orbital Jig Saw with Laser item #5926-06 was tested and meets our stringent quality standards. This product is warranted to be free from manufacturing defects in original materials, including original parts, and workmanship until July 31, 2008 or 2 years with proof of purchase excluding saw blade. The warranty is void if the defect is due to accidental damage, misuse, abuse, negle
ページ13に含まれる内容の要旨
WARRANTY CARD WARRANTY CARD Kingcraft Orbital Jigsaw with Laser, Item # 5926-06, Model #MIQ-FE-65 In case you find this product to be defective please send it within the warranty period to our service center. To avoid transport damages please send the product in the original packaging. In return you will receive your repaired item, a new product or a refund. Please fill in your details below and send it together with the product and purchase receipt. Please read t
