ページ1に含まれる内容の要旨
SNC-B2331(P)
Network Camera
User Manual
imagine the possibilities
Thanks you for purchasing this Samsung product.
To receive a more complete service, please visit
our website
www.samsungsecurity.com
RoHS compliant
Our product complies with “The Restriction Of the use of certain Hazardous Substances in electrical
and electronic equipment”, and we do not use the 6 hazardous materials- Cadmium (Cd), Lead
+6
(Pb), Mercury (Hg), Hexavalent Chromium (Cr ), Poly Brominated Biphenyls (PBBs), Poly Bro
ページ2に含まれる内容の要旨
overview CAUTION RISK OF ELECTRIC SHOCK. DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This symbol indicates that dangerous voltage consisting a risk of electric shock is present within this unit. This symbol indicates that there are important operating and maintenance instructions in the literature accompanying this unit. WARNING To reduce the risk of fi re or electri
ページ3に含まれる内容の要旨
● OVERVIEW 7. Do not install the unit in humid, dusty, or sooty locations. Doing so may cause fi re or electric shock. 8. If any unusual smells or smoke come from the unit, stop using the product. In such case, immediately disconnect the power source and contact the service center. Continued use in such a condition may cause fi re or electric shock. 9. If this product fails to operate normally, contact the nearest service center. Never disassemble or modify this product in any way. (SAMSUNG i
ページ4に含まれる内容の要旨
overview CAUTION 1. Do not drop objects on the product or apply strong blows to it. Keep away from a location subject to excessive vibration or magnetic interference. 2. Do not install in a location subject to high temperature (over 50°C), low temperature (below -10°C), or high humidity. Doing so may cause fi re or electric shock. 3. If you want to relocate the already installed product, be sure to turn off the power and then move or reinstall it. 4. Remove the power plug from the outlet when
ページ5に含まれる内容の要旨
● OVERVIEW FCC STATEMENT This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions : 1) This device may not cause harmful interference, and 2) This device must accept any interference received including interference that may cause undesired operation. Caution This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of FCC Rules. These limits are designed to provide reasonable protecti
ページ6に含まれる内容の要旨
overview IMPORTANT SAFETY INSTRUCTIONS 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8. Do not install near any heat sources such as radiators, heat registers, or other apparatus (including amplifi ers) that produce heat. 9. Do not defeat the safety purpose of the p
ページ7に含まれる内容の要旨
● OVERVIEW CONTENTS 6 important safety instructions OVERVIEW 9 Product Features 9 Recommended PC Specifi cations 10 What’s Included 2 11 At a Glance 13 Mounting the lens INSTALLATION & CONNECTION 15 Connecting with other Device 13 17 How to use the keyboard CAMERA SETUP controller 18 Main Menu 18 Profi le 17 19 Camera Setup 23 Privacy Zone 24 Others 25 System Info 25 Language 26 Connecting the Camera to an NETWORK CONNECTION IP Router With The xDSL/Cable AND SETUP Modem 27 Connecting the Came
ページ8に含まれる内容の要旨
overview 37 Connecting to the camera WEB VIEWER 38 Login 39 Installing ActiveX 40 Using the Live Screen 37 41 Backup 43 Accessing the Setup screen SETUP SCREEN 44 Default Setup 48 System Setup 51 Overlay Setup 43 52 Event Setup 57 Network Setup 59 Profi le APPENDIX 60 Terminology 61 Specifi cations 65 Frame Rate (NTSC) 59 71 Frame Rate (PAL) 77 Troubleshooting 8_ overview
ページ9に含まれる内容の要旨
● OVERVIEW PRODUCT FEATURES Support various communication protocols Supports TCP/IP, UDP, RTP/RTSP, SMTP for email, and FTP protocols as well as various internet protocols such as ARP, HTTP, HTTPS and DHCP. Web Browser-based Monitoring Using the Internet web browser to display the image in a local network environment. Automatic Local IP Setup Even a network novice can install it with minimum operations. Alarm If the camera equipped with an alarm sensor senses any motion, it will send a not
ページ10に含まれる内容の要旨
overview WHAT’S INCLUDED Please check if your camera and accessories are all included in the product package. Camera Holder (Mount) Camera C Mount Adaptor & Screws (2EA) User Manual/ User Manual IP INSTALLER CD Lens Options CS Lens C Lens 10_ overview
ページ11に含まれる内容の要旨
● OVERVIEW AT A GLANCE Front Side Item Description Camera Holder Used when you mount the camera onto the bracket by fixing the camera (Mount) Holes holder (mount) adaptor with the bracket. Auto Iris Lens Installed on the lens adaptor. (Optional) Auto Iris Lens Used to supply power and output signal to control the iris of the lens. Connector Wipe out a dirty surface of the lens softly with a lens tissue or cloth to which you have applied M ethanol. English _11
ページ12に含まれる内容の要旨
overview Rear Side SYSTEM POWER VIDEO RESET NETWORK 1 2 3 4 5 1,2 : ALARM IN 1,2 ACT LINK AC 24V 3 : GND GND DC 12V 4,5 : ALARM OUT 1,2 Item Description Video Out Port Video signal output port connected to the monitor. ON: The camera is turned on and connected to the network properly. SYSTEM Blinking: During DDNS setup, or in case of setup failure, or System, Power in a state of unstable network connection Indicators OFF: When the system is rebooting, or turned off ON: While the power
ページ13に含まれる内容の要旨
● INSTALLATION & CONNECTION installation & connection MOUNTING THE LENS Disconnect the power before proceeding. Mounting the CS lens Turn the optional CS lens clockwise to insert it. CS Lens Mounting the C lens Turn the C mount adaptor clockwise to insert it and do the same with the C lens. C Lens English _13
ページ14に含まれる内容の要旨
installation & connection Connecting the Auto Iris Lens connector Insert the lens connector into the corresponding hole of the camera. Focusing Turn the lens left or right to control the zoom and focus the lens so that you can view a clear, sharp object. 14_ installation & connection
ページ15に含まれる内容の要旨
● INSTALLATION & CONNECTION CONNECTING WITH OTHER DEVICE Monitor SYSTEM POWER VIDEO RESET NETWORK 1 2 3 4 5 1,2 : ALARM IN 1,2 ACT LINK AC 24V 3 : GND GND DC 12V 4,5 : ALARM OUT 1,2 Power Network Connecting to the monitor Connect the [VIDEO] port of the camera to the video input port of the monitor. Network Connection Connect the Network cable to the local network or to the Internet. Power Supply Use the screwdriver to connect each line of the power cable to the corresponding port of t
ページ16に含まれる内容の要旨
installation & connection Connecting to the I/O port box Connect the Alarm I/O signal to the corresponding port of the rear port box. 1 2 3 4 5 SYSTEM POWER VIDEO RESET NETWORK 1 2 3 4 5 1,2 : ALARM IN 1,2 1,2 : ALARM IN 1,2 ACT LINK AC 24V 3 : GND GND DC 12V 3 : GND 4,5 : ALARM OUT 1,2 4,5 : ALARM OUT 1,2 ALARM IN 1, 2 : Used to connect the alarm input signal. GND : Used for earth-grounding. ALARM OUT 1, 2 : Used to connect the alarm output signal. Alarm I/O Wiring Diagram AL
ページ17に含まれる内容の要旨
● CAMERA SETUP camera setup You can configure the camera settings using the Web Viewer. For accessing the Web Viewer, refer to "Network Connection and Setup". (page 26) M HOW TO USE THE KEYBOARD CONTROLLER Follow the steps below if you run the Web Viewer for setting the menus. 1. Launch the Web Viewer. 2. From the [Camera OSD] menu in the left pane, click [Menu]. The screen appears. 3. Click the Up/Down (▲▼) buttons to move to a desired item. ▲▼◄ ► 4. Click the four direction (
ページ18に含まれる内容の要旨
camera setup MAIN MENU You can configure the camera settings to your preference. PROFILE ** ** MAIN MENU MAIN MENU **** You can select a mode that is appropriate to the PROFILE camera installation environment. C CAMERA AMERA SET SET P PRIV RIVA ACY CY ZONE ZONE CAMERA SET O OTHER SET THER SET Confi gure the camera functions and settings. SYSTEM INFO SYSTEM INFO LANGUAGE LANGUAGE PRIVACY ZONE You can confi gure the privacy settings. OTHER SET You can confi gure more settings including
ページ19に含まれる内容の要旨
● CAMERA SETUP CAMERA SETUP You can configure the general settings of the camera module. Use the four direction (▲▼◄ ►) buttons to select a desired item. CAMERA ID Provide the ID and position for a camera that displays on the screen. For selecting and saving each menu item, refer to "How to use the keyboard controller". (page 17) 1. Select - . CAMERA CAMERA ID ID 2. Use the four direction (▲▼◄ ►) buttons to AB BCDEFGHIJKLMNOPQRSTUVWXYZO CDEFGHIJKLMNOPQRSTUVWXYZO _ _
ページ20に含まれる内容の要旨
camera setup MOTION ◄ ► CAMERA SET You can specify a level of AGC for controlling the CAMERA CAMERA ID ID ON ON IIRIS ALC RIS ALC camera motion. MMOTION (F OTION (F..F FAAST) ST)- --- -- Select F.FAST if you want to monitor a very fast DNR MID DNR MID moving object in a low contrast scene, and S.SLOW SSHUTTER OFF HUTTER OFF SENS-UP SENS-UP AUT AUTO O X4 X4 if monitoring a very slow moving, inanimate object in FFLICKERLESS OFF LICKERLESS OFF the same condition. XXDR MID DR MID DIS OFF DIS
