Hitachi BE-IR31の取扱説明書

デバイスHitachi BE-IR31の取扱説明書

デバイス: Hitachi BE-IR31
カテゴリ: ビデオアクセサリー
メーカー: Hitachi
サイズ: 0.26 MB
追加した日付: 8/4/2014
ページ数: 26
説明書を印刷

ダウンロード

使い方は?

私たちの目的は、皆様方にデバイスHitachi BE-IR31の取扱説明書に含まれたコンテンツを可能な限り早く提供することです。オンラインプレビューを使用すると、Hitachi BE-IR31に関してあなたが抱えている問題に対する解決策の内容が素早く表示されます。

便宜上

説明書Hitachi BE-IR31をこちらのサイトで閲覧するのに不都合がある場合は、2つの解決策があります:

  • フルスクリーン表示 – 説明書を(お使いのコンピュータにダウンロードすることなく)便利に表示させるには、フルスクリーン表示モードをご使用ください。説明書Hitachi BE-IR31のフルスクリーン表示を起動するには、全画面表示ボタンを押してください。
  • コンピュータにダウンロード - Hitachi BE-IR31の説明書をお使いのコンピュータにダウンロードし、ご自身のコレクションに加えることもできます。デバイス上のスペースを無駄にしたくない場合は、いつでもManualsBaseサイトでダウンロードすることもできます。
Hitachi BE-IR31 取扱説明書 - Online PDF
Advertisement
« Page 1 of 26 »
Advertisement
印刷版

多くの人々は画面表示ではなく印刷された説明書を読むほうを好みます。説明書を印刷するオプションも提供されており、上記のリンクをクリックすることによりそれを利用できます - 説明書を印刷。説明書Hitachi BE-IR31を全部印刷する必要はなく、選択したページだけを印刷できます。紙を節約しましょう。

要旨

次のページにある説明書Hitachi BE-IR31の内容のプレビューは、以下にあります。次のページにある説明書の内容をすぐに表示したい場合は、こちらをご利用ください。

内容要旨
ページ1に含まれる内容の要旨

BE-IR30 / 31
Infrared B/W Camera Module
Operation Guide
Please read this operation Guide carefully for proper operation, and keep it for future refernce.

ページ2に含まれる内容の要旨

Table of Contents 1. Introduction 2 2. General 2 3. Composition 2 4. Specifications 2 5. Notes to users 5 6. External view 7 7. Optical dimensions 9 8. Installation 10 9. Typical connection 11 10 External sync (BE-IR31) 13 11 Function settings and changes 11-1 AGC on / off 14 11-2 Gamma response 15 11-3 Auto electronic shutter on / off 16 11-4 Changes to fixed shutter mode 17 11-5 BE-IR30 external sync 18 11-6 BE-IR31 internal sync 19 11-7 HD and VD outp

ページ3に含まれる内容の要旨

1. Introduction Thank you very much for your purchase of the Hitachi BE-IR30/31 Black and White Camera Module. Prior to using this camera , read this manual carefully. 2. General The BE-IR30/31 is a monochrome camera module featuring sensitivity in the near infrared spectrum using a 1/3-inch size CCD imaging device. Resolution is outstanding, while the very small size provides optimum suitability for incorporation into equipment where space is limited. Model coding BE-IR3 Signal system N: E

ページ4に含まれる内容の要旨

4. . . .Specifications 2) Sensing area EIA : 6.00(H) 4.96(V)mm CCIR : 6.00(H) 4.96(V)mm 3) Signal format Conforming to EIA or CCIR. 4) Scanning system 2:1 interlaced 5) Hor. scanning frequency EIA : 15.734 kHz CCIR : 15.625 kHz 6) Vert. scanning frequency EIA : 59.94 Hz CCIR : 50 Hz 7) Sync system BE-IR30 : Internal sync BE-IR31 : External sync 8) External sync input HD & VD : 5V peak-to-peak negative Ω Input impedance : 1k ± Frequency deviation : 1% Ω 9) Video outpu

ページ5に含まれる内容の要旨

4. . . .Specifications 21) Standard lens f3.8 (BE-IR30B/31B only) Focal distance f 3.8 mm F value 2.0 Picture angle H 70.9 V 52.9 21) Dimensions BE-IR30A/31A: 34 (W) × 34 (H) × 20 (D) mm BE-IR30B/31B: 34 (W) × 34 (H) × 32 (D) mm (less lens) BE-IR30C/31C: 34 (W) × 34 (H) × 24 (D) mm 22) Mass BE-IR30A/31A: Approx. 15g (less cable) BE-IR30B/31B: Approx. 26g (including cable, less lens) BE-IR30C/31C: Approx. 19g (less cable) 23) Options • BE-IR30A/31A mount adapter (LA-IR20) • BE-IR30B/31B l

ページ6に含まれる内容の要旨

5. Notes to users Power supply Connect a 9V DC voltage (8.5 to 9.5V) from an external regulated DC power supply. Use a stable power supply without ripple and noise. Prior to turning on the power switch , check that the polarities of the power cable are correct , referring to the connection diagram (Page 11 , 12) To protect CCD (sensor) Do not touch the glass surface of the CCD sensor to avoid deterioration in picture quality due to dirt and scratches. If the glass surface of the senso

ページ7に含まれる内容の要旨

5. Notes to users Phenomena inherent to CCD imaging device Following are phenomena inherent to a CCD imaging device , and not defects. Smear and blooming When strong light (lamp , fluorescent lamp , reflected light , etc.) is shot , pale bands are displayed vertically above and below the light. In this case , change the angle of the camera so that such strong light does not enter the camera through the lens. Fixed pattern noise When the camera is operated in a high temperatur

ページ8に含まれる内容の要旨

6. External view BE-IR30B/31B BE-IR30 / 31 7

ページ9に含まれる内容の要旨

6. External view BE-IR30C/31C BE-IR30 / 31 8

ページ10に含まれる内容の要旨

6. External view BE-IR30A/31A 7. Optical dimensions Lens Lens-mount 19.2 ± 0.5 (C-mount) Extension of optical path due CCD 1.4 ± 0.2 to the thickness of CCD glass is considered. Base plate Imaging face BE-IR30 / 31 9

ページ11に含まれる内容の要旨

8. Installation When installing the camera in a housing or unit of equipment, secure with two M2 screws inserted into the 2.5 mm diameters holes of the SENS board base plate. Two 2.5 mm Dia. SENS board 1. Use the SENS board holds to install the camera. Avoid using only the Main board, due to risk of damage to the board connector. Notes : 2. Avoid unnecessary stress on the printed board when engaging and disengaging the connectors. 3. The screws securing the base plate and SENS board protr

ページ12に含まれる内容の要旨

9. Typical connection BE-IR30 Image processor or Connector Video monitor B7B-ZR (Note 1) Housing ZHR-7 BLK YEL GRN Regulated power supply (More then 300 mA) RED Note1 : • When more than one video monitor is connected in series , set the 75Ω termination switch on the last unit to ON. DC9V Note2 : • Supply voltage range : 8.5 to 9.5V (Note 2) • Be sure to check the polarities of the power source before turning on the external DC power supply. BE-IR30 / 31 11

ページ13に含まれる内容の要旨

9. Typical connection BE-IR31 Image processor or Connector Video monitor B7B-ZR (Note 1) Housing ZHR-7 BLK YEL GRN Regulated power supply (More then 300 mA) RED HD VD External sync signal GND Note1 : • When more than one video monitor is connected in DC9V series , set the 75Ω termination switch on the last unit (Note 2) to ON. Note2 : • Supply voltage range : 8.5 to 9.5V • Be sure to check the polarities of the power source before turning on the external DC power sup

ページ14に含まれる内容の要旨

10. External sync (BE-IR31) Supply sync signals (HD and VD) for BE-IR31 operation. Refer to connection on page 12. Horizontal and vertical drive signal inputs HD EIA: f(H) = 15.734 kHz 1 % VD EIA: f(V) = 59.94 Hz (f(V) = f(H) 262.5) Input level HD 4 to 6 Vp-p negative VD 4 to 6 Vp-p negative Input impedance 1 k Drive signal input waveform Vertical drive signal (VD) Horizontal drive signal (HD) T=1/f(H) T=1/f(V) 4 6Vp-p 4 6Vp-p Approx. 6.7µ s Approx. 0.6ms HD and VD

ページ15に含まれる内容の要旨

11. Function setting and changes When changing the function settings , perform the work with thorough care. Be sure to use anti-static measures such as a grounding band. Also observe safety precautions when soldering to avoid burn and fire hazards. Hitachi Denshi assumes on liability for damage or injury resulting from such work. Since the function setting can be provided at the time of shipment , consult a Hitachi Denshi representative. 11-1 AGC on / off Factory setting is AGC off (fixed g

ページ16に含まれる内容の要旨

11. Function setting and changes 11-2 Gamma response The factory setting is gamma on. If necessary , the gamma response can be changed as follows. Change the gamma response by changing the chip part. Gamma(γ)response R217 R218 R219 ON Absent 0Ω 0Ω Factory setting OFF 0Ω Remove Remove 0Ω : Part code RME1784 Description ERJ3GEYJ0R00V Location of chip capacitors (Main board side B) BE-IR30 / 31 15

ページ17に含まれる内容の要旨

11. Function setting and changes 11-3 Auto electronic shutter on / off Factory setting for auto electronic shutter is off. If necessary , it can be set to on. Absent the R259 , R260 chip to set the auto electronic shutter to on. Auto electronic shutter R259 R260 OFF 0Ω 0Ω Factory setting ON Absent Absent 0Ω : Part code RME2068 Description ERJ2GE0R00X Location of chip resistors (Main board side B) BE-IR30 / 31 16

ページ18に含まれる内容の要旨

Fixed shutter mode 11. Function setting and changes 11-4 Changes to fixed shutter mode The fixed shutter mode can be changed by replacing the chip parts indicated below. Mode R259 R260 R261 R262 R263 R264 R265 R266 R267 R268 R269 Factory Normal mode 0Ω 0Ω Absent 0Ω Absent 6800 10k 27k 10k 10k 27k setting Auto electronic Remove Remove Absent 0Ω Absent shutter mode EIA 1/100 Remove 0Ω 0Ω Remove Absent 0Ω 0Ω Remove 0Ω 0Ω Remove CCIR 1/120 1/250 Remove Remove 0Ω 1/500 Absent Remove 0Ω 0Ω 0Ω Remove

ページ19に含まれる内容の要旨

11. Function setting and changes 11-5 BE-IR30 external sync The BE-IR30 factory setting is for internal sync. If required, this can be changed to external sync by changing chip parts. Change the following chip parts for external sync operation. Sync system R280 R281 R282 R284 Internal 100 Ω Absent Absent 0 Ω Factory setting External Delete 0 Ω 100 Ω Delete 0 Ω Part code RME1784 Type ERJ3GEYJ0R00V 100 Ω Part code RME1797 Type ERJ3GEYJ101V (Main board side A) (Main board side B) Location of c

ページ20に含まれる内容の要旨

11. Function setting and changes 11-6 BE-IR31 internal sync The BE-IR31 factory setting is for external sync. If required, this can be changed to internal sync by changing chip parts. Change the following chip parts for internal sync operation. Sync system R280 R281 R282 R284 External Absent 0 Ω 100 Ω Absent Factory setting Internal 100 Ω Delete Delete 0 Ω 0 Ω Part code RME1784 Type ERJ3GEYJ0R00V 100 Ω Part code RME1797 Type ERJ3GEYJ101V (Main board side A) (Main board side B) Location of c


類似の説明書
# 取扱説明書 カテゴリ ダウンロード
1 Hitachi BE-IR30 取扱説明書 ビデオアクセサリー 1
2 Sony HDCU-900 取扱説明書 ビデオアクセサリー 46
3 Sony 370PL 取扱説明書 ビデオアクセサリー 0
4 Sony 570WSPL 取扱説明書 ビデオアクセサリー 0
5 Sony ACC-CN3BC 取扱説明書 ビデオアクセサリー 1
6 Sony CA-590 取扱説明書 ビデオアクセサリー 2
7 Sony CA-590P 取扱説明書 ビデオアクセサリー 3
8 Sony FCB-EX480C 取扱説明書 ビデオアクセサリー 18
9 Sony LSF-H58 取扱説明書 ビデオアクセサリー 0
10 Sony FCB-IX11A 取扱説明書 ビデオアクセサリー 7
11 Sony ERA-MS008 取扱説明書 ビデオアクセサリー 2
12 Sony ACC-CFR 取扱説明書 ビデオアクセサリー 0
13 Sony Aqty Pack APK-WA 取扱説明書 ビデオアクセサリー 1
14 Sony LCM-FD88 取扱説明書 ビデオアクセサリー 0
15 Sony HKCU-903 取扱説明書 ビデオアクセサリー 1