ページ1に含まれる内容の要旨
MOSFET POWER AMPLIFIERS
Installation Instructions / Owner's Manual
100SX 200SX 400SX 440SX
600SX 640SX 800SX 1200SX
ページ2に含まれる内容の要旨
INTRODUCTION Congratulations on your purchase of a California state-of-the-art power amplifier. Your selection of a California car audio product indicates a true appreciation of fine musical reproduction. Whether adding to an exi sting system or including your California amplifier in a new system, you are certain to notice immediate performance benefits. KEEP YOUR SALES RECEIPT Take this time to attach your sales receipt to the manual and put in a safe place. In case of any unforeseen re
ページ3に含まれる内容の要旨
SAFETY PRECAUTIONS Fuse amplifier's power wire at the battery. Be sure to fuse the power wire within 12" of the car's battery. This will protect the car's battery in case of a short circuit between the power amplifier and battery. THIS IS A MUST, the amplifier's built-in fuse will only protect the power amplifier not the car's battery! Use high grade wire connectors. To ensure maximum power transfer and secure safe connections, it is recommended to use high grade connectors where needed.
ページ4に含まれる内容の要旨
FEATURES AND BENEFITS DC Offset Protection This circuit protects the output of the amplifier against DC voltage. If for some reason DC voltage is detected at the output stage, the amplifier will shut down protecting the speakers from direct current. Short Circuit Protection The circuit protects the amplifier from damage due to a short found in the speakers or wiring. If one of the speakers or its wiring comes in contact with ground, the amplifier will shut down. To resume normal operatio
ページ5に含まれる内容の要旨
Bass Boost For added low frequency performance all amplifiers are equipped with 12 dB bass boost. Power Fusing This protects the amplifier against short circuits and excessive current. Remote Turn-on Automatically turns amplifier on when connected to the head unit's remote output. The amplifier will turn on and off with the head unit to save current consumption. This control also operates the reset circuit for the amplifier's protection. It must be connected with the head unit in order
ページ6に含まれる内容の要旨
MOUNTING LOCATION Before you start the installation, it will be necessary to find a mounting location for the amplifier. Find a location in which the amplifier will receive adequate ventilation in order to dissipate the heat it develops during operation. Two popular mounting locations are in the trunk or under the seat. Select the location in which you wish to mount the amplifier. Use caution when mounting amplifier, there are many wires, gas lines, vacuum lines, brake lines as well a
ページ7に含まれる内容の要旨
POWER CONNECTIONS B+ GND REM L Bridged R Fuse Speaker Output I IN N- -L LI IN NE E P PO OW WE ER R F FU US SE E M MO OU UN NT TE ED D W WI IT TH HI IN N 1 12 2" " R RA AD DI IO O' 'S S R RE EM MO OT TE E F FR RO OM M B BA AT TT TE ER RY Y R RE EC CO OM MM ME EN ND DE ED D T TU UR RN N- -O ON N O OU UT TP PU UT T ( (N NO OT T P PR RO OV VI ID DE ED D) ) - - + + 9 94 4..7 7 C CA AR R B BA AT TT TE ER RY Y + +1 12 2V V IMPORTANT! Before making any connections, disconnect the car's battery until t
ページ8に含まれる内容の要旨
SIGNAL CONNECTIONS Connect the RCA output of the head unit (AM/FM cassette player, CD, or DAT) to the RCA input terminals of the amplifier. To make these connections, we recommend high quality RCA cables, which are available at your local car audio retailer. Run signal wires away from electrical wires to avoid possibility of induced noise from the car's electrical system (i.e. popping noises or engine noise). Please note that when making these connections the signal inputs correspond with
ページ9に含まれる内容の要旨
HIGH LEVEL CONNECTIONS (OPTIONAL) If a low level RCA signal source is not available, you may still wire the models 100SX, 200SX, and 400SX with high-level or speaker level outputs from your head unit. However, only speaker leads from a "floating ground" system may be used (see diagram below). Use the strip Connector located on the end of the amplifier to make this connection. The strip connector should be connected with the front or rear, 2 channels of your head unit. Note: The speaker l
ページ10に含まれる内容の要旨
SPEAKER CONNECTIONS Make the speaker connections using speaker wire that is at least 14 gauge or heavier. As with any audio component, proper phasing of the amplifier and speakers is essential for strong bass response. When connecting, make sure that positive (+) from the amplifier is connected to the positive (+) of the speaker, and the same for negative (-). TWO CHANNEL SPEAKER CONNECTIONS B+ REM GND Bridged L R Fuse Speaker Output + + - - + + - - 4 4 O Oh hm m S Sp pe ea ak ke ers rs (2 (2
ページ11に含まれる内容の要旨
SPEAKER CONNECTIONS (BRIDGED) The California amplifiers are capable of being bridged in a mono configuration. This feature allows you the flexibility of using the amplifier to drive a ** subwoofer or a center channel. In this configuration the amplifier sums the right and left channel to deliver one channel (mono) output. Please note: in order for the amplifier to sum right and left signal information, both right and left RCA connections must be made. **CAUTION! In the bridged mode, the am
ページ12に含まれる内容の要旨
++ -- ++-- SPEAKER CONNECTIONS (TRI-MODE) The amplifier is capable of running in a Mono / Stereo mode. This feature gives the 2channel amplifier the ability to run stereo satellites (midbass & tweeter) simultaneously with a mono subwoofer. These connections are more complicated because they require the use of passive crossover networks (Not provided) to divide the frequencies to the speakers. We have included a sample diagram for 4 Ohm connections. If you wish to use multiple speakers to
ページ13に含まれる内容の要旨
SETTING THE CROSSOVER AND BASS BOOST Select your crossover type and frequency. (Please note: If you intend to use the amplifier in the Tri-mode configuration, it is necessary to set the crossover control to the "Off" setting in order to receive full range output) The California amplifiers are equipped with a built-in variable crossover network allowing you to select the crossover type (i.e. Low-Pass or Hi-Pass) and the desired crossover point. For example if you wish to drive a pair
ページ14に含まれる内容の要旨
TROUBLE SHOOTING THE SYSTEM We have put together this trouble-shooting guide if you experience problems after installing the amplifier. Please keep in mind that the majority of problems incurred are caused by improper installation and not the equipment itself. In addition, there are many components in the system that could cause various signal problems such as inducted electrical noise and engine noise. Before you can properly address the problem, you must first find the component that is
ページ15に含まれる内容の要旨
SPECIFICATIONS 100SX 200SX 400SX Output Power @ 4 Ohm 2 x 70W 2 x 120W 2 x 200W RMS Power @ 4 Ohm 2 x 35W 2 x 60W 2 x 100W RMS Power @ 2 Ohm 2 x 50W 2 x 90W 2 x 150W Bridged RMS @ 4 Ohm 1 x 100W 1 x 180W 1 x 300W THD @ RMS Power <0.07% <0.07% <0.07% Frequency Response 20Hz ~ 30Khz 20Hz ~ 30Khz 20Hz ~ 30Khz Signal To Noise >105dB >105dB >105dB Stereo Separation 85dB 85dB 85dB RCA Input Sensitivity 200mV ~ 8V 200mV ~ 8V 200mV ~ 8V RCA Input
ページ16に含まれる内容の要旨
SPECIFICATIONS 800SX 1200SX Output Power @ 4 Ohm 2 x 400W 2 x 600W RMS Power @ 4 Ohm 2 x 200W 2 x 300W RMS Power @ 2 Ohm 2 x 300W 2 x 450W Bridged RMS @ 4 Ohm 1 x 600W 1 x 900W THD @ RMS Power <0.07% <0.07% Frequency Response 20Hz ~ 30Khz 20Hz ~ 30Khz Signal To Noise >105dB
ページ17に含まれる内容の要旨
LIMITED WARRANTY Profile Consumer Electronics, Inc. warrants this product to be free from defects in material and workmanship for a period of One (1) Year from the date of sale to the original consumer purchaser. If this product is proven to be defective within this one year period, Profile will repair it when said product is returned, with a copy of the dated sales receipt, freight prepaid to Profile. This warranty is valid only in the United States.
ページ18に含まれる内容の要旨
WARRANTY REPAIR POLICY In the unlikely event of product failure, the following procedures should be followed 1) The unit must be under the 1-year warranty period. 2) The unit must have no physical damage. 3) A copy of the original proof of purchase must be sent with the unit. 4) Include a brief description of the problem or failure with the unit. 5) Include the return street address and daytime telephone number. 6) Allow 2~3 weeks for rep
ページ19に含まれる内容の要旨
By PROFILE CONSUMER ELECTRONICS, INC. 17625 FABRICA WAY CERRITOS, CA 90703 TEL: (714) 690-4949 FAX: (714) 690-4957 WORLD WIDE WEB: WWW.PROFILEUSA.COM
