ページ1に含まれる内容の要旨
ページ2に含まれる内容の要旨
This document was prepared and written by the Technical Documentation department at: Crestron Electronics, Inc. 1 - 888 - CRESTRON Rockleigh, NJ 07647 15 Volvo Drive
ページ3に含まれる内容の要旨
Crestron ST - TUNE Contents Integrated AM/FM/TV T - 1 1 1 2 6 8 8 9 10 11 14 - 15 - - 15 20 21 22 22 24 24 24 - 25 25 25 - 27 28 35 35 35 - • • i Contents DOC. 5833A Operations Guide CRESTRON Limited Warranty Merchandise Returns / Repair Service Return and Warranty Policies Appendix 3: Upgrade Firmware Version Prior to 2.17 TUNE TV Receptions Appendix 2: STI Fabrication Instructions Materials Required Gain AM Antenna Appendix 1: High F
ページ4に含まれる内容の要旨
ページ5に含まれる内容の要旨
ページ6に含まれる内容の要旨
ページ7に含まれる内容の要旨
ページ8に含まれる内容の要旨
Integrated AM/FM/TV Tuner - TUNE AUDIO (L + R) This pair of RCA jacks output the left (white center insulator) and right (red center insulator) channel line - vel audio to an audio processor such as the CNX - PAD8. The audio can also be connected to the audio inputs of a TV monitor, audio switcher and/or audio distribution equipment. - ator composite input. AM This RCA jack is used to input AM radio signals via the supplied AM antenna. The center insulator of this jack is white. Usin
ページ9に含まれる内容の要旨
Crestron ST - TUNE This LED (yellow) indicates that the SIMPL program currently loaded in the control - TUNE. The LED flashes when communication with the Cresnet system and the ST - TUNE is occurring. The AM , , (Weather Radio), or indicators contain four LEDs (red) to the active band of the ST - TUNE. The digital display shows the radio These three LEDs (red) indicate the reception status of the ST - TUNE. The LED indicates the strength of the incomin g FM signal, the stea
ページ10に含まれる内容の要旨
ページ11に含まれる内容の要旨
ページ12に含まれる内容の要旨
Integrated AM/FM/TV Tuner - TUNE NOTE: Equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. The equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance w ith the instructions, may cause harmful interference to radio communications. However, th
ページ13に含まれる内容の要旨
Crestron ST - TUNE When calculating the wire gauge for a particular Cresnet run, the length of the run and the load factor of each network unit to be connected must be taken into consideration. If Cresnet units are to be daisy - chained on the run, the load factor of - chained must be added together to determine the the entire chain. If the unit is a home - run from a Crestron system power supply network port, the load factor of that unit is the load factor of the entire run. The resista
ページ14に含まれる内容の要旨
ページ15に含まれる内容の要旨
Crestron ST - TUNE Attach one of the ST - s oftware is running). - e menu, select to open the Crestron Viewport. From the Viewport menu, select . The software checks the baud rate and then opens the “Set Network ID” x. In the “Set Network ID” dialog box, select the ST - TUNE from the Current Network Devices - TUNE. Click to initiate the chang e. This will display the “ID command has been sent” dialog box. In the “Command Complete” dialog box, click OK . In the Curren
ページ16に含まれる内容の要旨
Integrated AM/FM/TV Tuner - TUNE Accessing the Port Settings Dialog Box erify the communications settings. Make sure that parity is set to , data bits to , and NOTE: If performing a firmware upgrade via Ethernet, select TCP/IP as the connection type and provide the IP address. Port Settings Dialog Box • • - Operations Gu ide - DOC. 5833A TUNE Integrated AM/FM/TV Tuner: ST 12 is selected. XModem Eight None Refer to the dialog box shown below and v 5. ST Crestron
ページ17に含まれる内容の要旨
Crestron ST - TUNE (alternatively, ). In the Viewport return display, observe the firmware version of the - Perform the appropriate step. 8a. If the firmware version is version 2.17 or later , continue with this procedure. If the firmware version is 8 of “Appendix 3” that begins on page 28 . File Transfer | from the Viewport menu . - Integrated AM/FM/TV Tuner: ST - • • 13 TUNE DOC. 5833A Operations Guide ect Load Network Device Sel Load Network Device As shown
ページ18に含まれる内容の要旨
Integrated AM/FM/TV Tuner - TUNE Refer to the diagram below. Select the NET ID of the ST - TUNE and then click OK . select the . The trans fer will NOTE: When the external power pack is disconnected from the ST - TUNE, operating power will automatically switch to Cresnet power supplied via the NET connector(s). To remove power from the unit, make sure both external power pack and NET connector(s) are removed. - TUNE, wait several seconds and C - e, and disconnect the
ページ19に含まれる内容の要旨
Crestron ST - TUNE - first section provides initial configuration info rmation, the second section details the using a textual description and a block diagram, and the fourth section describes the screens of an advanced example program. NOTE: The Windows. If not, refer to the extensive help information provided with the software. NOTE: VT Pro - e (version 2.1.8 or later) is required for the ST - touchpanels. The latest - - E Library) of Crestron’s ). New users are required to register
ページ20に含まれる内容の要旨
Integrated AM/FM/TV Tuner - TUNE NOTE: Al l signals listed in the following tables are signals unless noted otherwise. A digital signal can be high (logic level of 1), low (logic level of 0), and also have rising edge (when it goes from low to high) and falling edge (from high to low) tran work at the logic levels or on transitions. Detail View of the ST - • • - Operations Gu ide - DOC. 5833A TUNE Integrated AM/FM/TV Tuner: ST 16 TUNE Symbol in SIMPL Windows’ Programming Manager s
