ページ1に含まれる内容の要旨
Owner’s Manual
TA1501C Clark Synthesis Amplifier
PROFESSIONAL
INSTALLERS:
QUICK SETUP
INSTRUCTIONS
ON PAGE 13!
Table of Contents
Company Overview 2
Warranty 3
Safety Instructions 4
Product Introduction 5
Unpacking Your Amplifier 6
Product Overview 7
Setting Up Your Amplifier 13
Operating Your Amplifier 20
NOTE: READ THIS MANUAL BEFORE
OPERATING THE AMPLIFIER. FAILURE Specifications 22
TO FOLLOW THE INSTRUCTIONS IN THIS
Troubleshooting 23
MANUAL MAY RESULT IN DAMAGE TO THE
Glossary of Terms
ページ2に含まれる内容の要旨
COMPANY OVERVIEW Thank you for purchasing a Clark Synthesis Tactile Sound Amplifier! We are confident this product will be a welcome addition to your audio system. For many years, Clark Synthesis has been providing Tactile Sound Transducers for use in home theaters, listening rooms, outdoor decks, military simulators, theme park attractions, game chairs, professional music, and swimming pools. With such a variety of products, it is likely that Clark Synthesis has the right type of transducer
ページ3に含まれる内容の要旨
WARRANTY United States Warranty and Return Policy TA1501C CLARK SYNTHESIS AMPLIFIER WARRANTY Clark Synthesis, Inc. warranties the TA1501C Amplifer to be free from defects and workmanship under normal use for a period of two (2) years from date of original purchase. Should warranty service be necessary, Clark Synthesis, Inc. will (at its discretion) repair or replace the defective merchandise with equivalent merchandise at no charge. This warranty is valid for the original purchaser and is not
ページ4に含まれる内容の要旨
! SAFETY INSTRUCTIONS 1. READ THESE INSTRUCTIONS. 2. KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE. 3. HEED ALL WARNINGS. 4. FOLLOW ALL INSTRUCTIONS. 5. DO NOT USE THIS AMPLIFIER NEAR WATER. 6. CLEAN ONLY WITH A DRY CLOTH. 7. DO NOT BLOCK ANY VENTILATION OPENINGS. INSTALL IN ACCORDANCE WITH THE MANUFACTURER’S INSTRUCTIONS. 8. DO NOT INSTALL NEAR HEAT SOURCES SUCH AS RADIATORS, HEAT REGISTERS, STOVES, OR OTHER EQUIPMENT. 9. DO NOT DEFEAT THE SAFETY PURPOSE OF THE POLARIZED OR GROUNDING TYPE PLUG
ページ5に含まれる内容の要旨
PRODUCT INTRODUCTION OVERVIEW OF THE AMPLIFIER The TA1501C amplifier is the first audio amplifier designed exclusively for use with Clark Synthesis transducers. This amplifier incorporates the latest digital technology and provides features not available on many amplifiers. Please read this manual in its entirety so you can get the maximum enjoyment from your Clark Synthesis product(s). USING THIS AMPLIFIER WITH A CLARK SYNTHESIS TRANSDUCER The TA1501C amplifier works with all Clark Synthesi
ページ6に含まれる内容の要旨
UNPACKING YOUR AMPLIFIER PACKAGE CONTENTS Please remove the amplifier and accessories from the carton. You should have the following: • (1) TA1501C Amplifier • (1) AC Power Cord • (4) Amplifier Feet • (1) Y Adapter Cable (Color may vary from the image shown here) • (1) Operating Manual CONTACT INFORMATION IF PARTS ARE MISSING If you are missing any items, please contact Clark Synthesis at 1-800-898-1945. We recommend that you save the original carton to use if you ever have to ship the amplifie
ページ7に含まれる内容の要旨
PRODUCT OVERVIEW Front Panel Rear Panel Ventilation Threaded Foot Hole Threaded Foot Hole Vents www.clarksynthesis.com TA1501C Amplifier 7
ページ8に含まれる内容の要旨
PRODUCT OVERVIEW Front Panel Overview Gain (Volume) Control Crossover (X-Over) Control Auto/On Switch Low Pass/Bypass Switch Power Indicator Light www.clarksynthesis.com 8 TA1501C Amplifier
ページ9に含まれる内容の要旨
PRODUCT OVERVIEW Front Panel Overview GAIN (VOLUME) CONTROL The Gain (Volume) Control on the face of the TA1501C amplifier controls the degree to which the input signal is amplified. The gain level, combined with the level of the input signal, determines the actual volume output. CROSSOVER (X-OVER) CONTROL The Crossover Control on the face of the TA1501C amplifier controls the range of low-frequency (bass) sound sent to the output device, i.e. transducer, speaker, etc. This control is only f
ページ10に含まれる内容の要旨
PRODUCT OVERVIEW Rear Panel Overview AC Power Switch High/Low Input Signal Switch Audio Input/Output Connectors AC Power Cord Connector Transducer (IEC-601) Connector www.clarksynthesis.com 10 TA1501C Amplifier
ページ11に含まれる内容の要旨
PRODUCT OVERVIEW Rear Panel Overview AC POWER SWITCH The AC Power Switch controls the AC power to the amplifier. The round circle on the switch represents “OFF” and the line represents “ON.” This switch works independently from the Auto/ On Switch, which is discussed in the Front Panel Overview section. AUDIO INPUT/OUTPUT CONNECTORS The Audio Input/Output Connectors accept standard RCA plugs. These connectors are split into Left and Right channels, as indicated by L and R on the panel. The Lef
ページ12に含まれる内容の要旨
SETTING UP YOUR AMPLIFIER This page intentionally left blank www.clarksynthesis.com 12 TA1501C Amplifier
ページ13に含まれる内容の要旨
SETTING UP YOUR AMPLIFIER Quick Setup Instructions The following instructions are a quick overview of the steps necessary to install your new amplifier. For more detailed instructions, please refer to the sections in the manual that are referenced below. 1. Remove the amplifier from its package (for package contents, see “Unpacking Your Amplifier” on page 6). 2. Insure you have set the amplifier to the following settings: • AC Power Switch is set to “Off” • Gain (Volume) Control is set to “M
ページ14に含まれる内容の要旨
SETTING UP YOUR AMPLIFIER Initial Settings Prior to Making Connections CAUTION: Before connecting any wires or input/output lines, insure all equipment is off and no signals are being sent from the input device. ! In order to reduce the chances of accidentally damaging the amplifier or transducer, please set the amplifier controls to the safety positions described and shown below: • Set the AC Power Switch on the back of the amplifier to the “Off” position (see photo #1) • Set the Gain (Volume
ページ15に含まれる内容の要旨
SETTING UP YOUR AMPLIFIER Mounting the Amplifier(s) on a Clamping Rackshelf Up to three (3) TA1501C Amplifiers may be installed in a 2U rack space using a Clamping Rackshelf. When mounting in a Clamping Rackshelf, DO NOT install the feet provided with the amplifier. The bottom of the amplifier MUST be in full contact with the metal rackshelf. CAUTION: Insure even spacing between the amplifiers and the side walls of the shelf. This will aid in providing adequate ventilation for the amplifier(s)
ページ16に含まれる内容の要旨
SETTING UP YOUR AMPLIFIER Connecting the Audio Source HOME THEATER There are several different ways to hook up your system in terms of which source material (signal) is delivered to the amplifier(s) and transducer(s). Since our inception, we have discovered that approximately half of our customers prefer using the LFE/SUB signal with their transducers. The other half prefer using the Right Front (RF) and Left Front (LF) signals. Additionally, there are a few people who like to use multiple s
ページ17に含まれる内容の要旨
SETTING UP YOUR AMPLIFIER Right Front (RF) and Left Front (LF) Hookup For this hookup, connect the RF and LF Pre-Amp Outputs to the TA1501C amplifier inputs. NOTE: Not all receivers have Pre-Amp outputs for the Right Front and Left Front outputs. If you have a question about your receiver’s outputs, please consult your owner’s manual or contact your receiver’s manufacturer. TA1501C Amplifier Surround-Sound Receiver L Pre-Amp Audio Out LF RF R OUT IN – + Transducer Output Transducer Multiple S
ページ18に含まれる内容の要旨
SETTING UP YOUR AMPLIFIER Connecting the Transducer to the Amplifier If you are able to locate the amplifier within 3 feet of the transducer (3 ft. is the approximate length of the speaker wire attached to the transducer), connect the transducer wires directly to the amplifier. This can be done by unscrewing the wire binding posts, inserting the wire through the hole in the post (see photo #1 on this page), and then retightening the binding posts (see photo #2). To insure you have a secure c
ページ19に含まれる内容の要旨
SETTING UP YOUR AMPLIFIER Using the Powered Loop-Through to Run Multiple Transducers The TA1501C has powered loop-through. This feature enables the user to take the signal from an audio source and pass it to a series of TA1501C amplifiers in order to drive multiple transducers. The drawing for this type of hookup is shown below. Use a standard “Y” adapter to get the signal from the audio source (e.g., from the LFE/SUB output). If the input signal is coming from two ports (e.g., from the RF a
ページ20に含まれる内容の要旨
OPERATING YOUR AMPLIFIER Balancing the Transducer with the Subwoofer Once you have properly set up your amplifier, it is important to take time to balance the transducer and subwoofer sound. The volume of the transducer is controlled by the receiver and will rise or fall in direct proportion to that of the primary speakers. This proportion is determined by both the volume setting on the receiver and the gain setting on the TA1501C amplifier. NOTE: Some receivers have internal, automatic balan
