ページ1に含まれる内容の要旨
TL-PS110U
Single USB2.0 Port Fast Ethernet Print
Server
Rev: 2.0.0
1910010381
ページ2に含まれる内容の要旨
COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-LINK TECHNOLOGIES CO., LTD. Copyright © 2010 TP-LINK TECHNOLOGIES CO.,
ページ3に含まれる内容の要旨
FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarante
ページ4に含まれる内容の要旨
FCC RF Radiation Exposure Statement This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter. “To comply with FCC RF exposure compliance requirements, this grant is applicable to only Mobile Configurations. The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all per
ページ5に含まれる内容の要旨
CONTENTS Chapter 1. Introduction.........................................................................................1 1.1 Product Overview ......................................................................................................1 1.2 Components and Features ........................................................................................1 1.3 LED Indicator.............................................................................................................1
ページ6に含まれる内容の要旨
TL-PS110U Single USB2.0 Port Fast Ethernet Print Server Chapter 1. Introduction 1.1 Product Overview The external print servers enhance capability by letting you place your printers at convenient locations directly on the Ethernet network, and by increasing network printer performance and management. Please note that the print server does not support printing with host-based printers, e.g. CAPT, GDI, PPA. 1.2 Components and Features One USB2.0 port Fast Ethernet network port: RJ- 45
ページ7に含まれる内容の要旨
TL-PS110U Single USB2.0 Port Fast Ethernet Print Server Chapter 2. Hardware Installation 2.1 Preparation Before you start, you should prepare the following items: One printer with USB port One USB printer cable One Router 2.2 Connection Follow the instructions below to connect the print server. Figure 2-1 is a typical typology for the print server. Power off the printer. Connect the print server to your printer with the USB cable. Connect the print server to your Router with
ページ8に含まれる内容の要旨
TL-PS110U Single USB2.0 Port Fast Ethernet Print Server Chapter 3. How to Configure the Print Server 3.1 Using PSWizard in Windows XP/ Windows Vista/ Windows 7 To connect to the print server using PSWizard, the configuration for Windows XP, Windows Vista and Windows 7 are similar. Here take Windows XP for example. 1. Insert the setup CD into your CD-drive. The autorun program will be started as shown in Figure 3-1. Select the model (TL-PS110U) of your print sever. Figure 3-1 2. Choos
ページ9に含まれる内容の要旨
TL-PS110U Single USB2.0 Port Fast Ethernet Print Server 3. Then you will enter to the “Welcome” page as shown in Figure 3-3. Click Next. Figure 3-3 4. From the “Select A Print Server” screen as shown in Figure 3-4, select the print server that you want to configure and click Next. Figure 3-4 4
ページ10に含まれる内容の要旨
TL-PS110U Single USB2.0 Port Fast Ethernet Print Server 5. On the Change Settings screen as shown in Figure 3-5, select Yes or No. Select “Yes” if you want to change the settings. The TL-PS110U is produced without password. Click Next and then appears “TCP/IP Settings” screen as shown in Figure 3-6. Proceed with the following steps. Select “ No” if you don’t need to change any settings. Click Next and then appears Figure 3-9. Skip to Step 8. Figure 3-5 6. On “TCP/IP Settings” page s
ページ11に含まれる内容の要旨
TL-PS110U Single USB2.0 Port Fast Ethernet Print Server Figure 3-6 7. Confirm your settings on the screen in Figure 3-7. Click Next and your changes will be saved as shown in Figure 3-8. Figure 3-7 6
ページ12に含まれる内容の要旨
TL-PS110U Single USB2.0 Port Fast Ethernet Print Server Figure 3-8 8. After that the “Select a Printer” page will appear, as shown in Figure 3-9. If the printer desired has already existed in the list, select it and then click Next and skip to Step 16 to complete the installation. If you never use a printer on your computer before but also want to share printing, click Add New Printer button in Figure 3-9 and then Figure 3-11 appears. Follow the steps below to install the printer d
ページ13に含まれる内容の要旨
TL-PS110U Single USB2.0 Port Fast Ethernet Print Server Figure 3-9 Note: To add a new printer, you can also go Start > Printers and Faxes, and then click “Add a printer” on the left to begin the following installation as shown in Figure 3-10. Figure 3-10 9. Click Add New Printer to launch Windows Add Printer Wizard. Click Next. 8
ページ14に含まれる内容の要旨
TL-PS110U Single USB2.0 Port Fast Ethernet Print Server Figure 3-11 10. Make sure the Automatically detect and install my Plug and Play printer check box is NOT checked. Then click Next. Figure 3-12 11. Check “Use the following port” radio button and select “LPT1: (Recommended Printer Port)” from the pull-down list. Then click Next. 9
ページ15に含まれる内容の要旨
TL-PS110U Single USB2.0 Port Fast Ethernet Print Server Figure 3-13 12. Select Manufacturer and Printer from the lists of printer’s driver. Then click Next. Figure 3-14 13. If you already have the printer’s driver installed, you will be asked whether to keep it or to replace it. Click Next. Supply a name for the printer and choose whether you want to make it your default printer. Then click Next. 10
ページ16に含まれる内容の要旨
TL-PS110U Single USB2.0 Port Fast Ethernet Print Server Figure 3-15 14. Then, choose whether you want to share the printer with other network users, print a test page (please select No.), etc. Select the appropriate radio-button and click Next. Figure 3-16 15. Click Finish. 11
ページ17に含まれる内容の要旨
TL-PS110U Single USB2.0 Port Fast Ethernet Print Server Figure 3-17 16. Then you will see the printer be added to the list. Select the printer and click Next. Follow the step by step instruction to finish the installation. Figure 3-18 17. From Windows system, go to Start > Printers and Faxes and highlight your newly installed printer. Right-click it, and then select Properties. 12
ページ18に含まれる内容の要旨
TL-PS110U Single USB2.0 Port Fast Ethernet Print Server Figure 3-19 18. Select Ports and verify that the print server’s port appears. Figure 3-20 19. Go to General; click Print Test Page to verify the configuration. 13
ページ19に含まれる内容の要旨
TL-PS110U Single USB2.0 Port Fast Ethernet Print Server Figure 3-21 Note: If you wish to install more print servers, repeat the above steps. 3.2 Using Web Management Page in Windows XP/ Windows Vista/ Windows 7 To connect to the print server using the web management page, the configuration for Windows XP, Windows Vista and Windows 7 are similar. Here take Windows XP for example. 1. On the Windows taskbar, click the Start->Control Panel. 14
ページ20に含まれる内容の要旨
TL-PS110U Single USB2.0 Port Fast Ethernet Print Server Figure 3-22 2. Select and double-click Networking Connections. Figure 3-23 3. Right click Wireless Network Connection, and select Properties. 15
