ページ1に含まれる内容の要旨
T E C H N O L O G I E S
Owner’s Manual and
Installation Guide
RUB1.1000D
RUB1.1600D
RUB1.2500D
ページ2に含まれる内容の要旨
CONGRATULATIONS! You now own a Limited Edition RUBICON Amplifier, the product of an uncompromising design and engineering philosophy. To maximize the performance of your system, we recommend that you thoroughly acquaint yourself with its capabilities and features. Please retain this manual and you sales receipt for future reference. Soundstream amplifiers are the result of American innovation and the highest quality control standards. When properly installed, they will provide you with many ye
ページ3に含まれる内容の要旨
FEATURES Total Harmonic Distortion:0.5% Frequency Response: 15-150Hz Signal to Noise Ratio: 105dB Damping Factor: >250 Input Sensitivity 100mV - 8V 50-150Hz,12dB Low Pass Fiter 45Hz, 0-18dB Bass Boost 10-40Hz, 12dB Subsonic Filter 180° Phase Switch Midnight Blue Finish w/ Brushed Accents Remote Gain Control Master/Slave Operation Pre-amp Outputs 3
ページ4に含まれる内容の要旨
SPECIFICATIONS Signal/Noise Ratio >105dB Frequency Response 15Hz-150Hz THD 0.50% LPF 50Hz -150Hz,12dB Input Voltage Range 11-16 Volts DC High Impedance RCA/LINE 30K Ohms Level Input Impedance POWER RATINGS & FUSE MODEL 4 ohm 2 ohm 1 ohm FUSE RUB1.1000D 600W 800W 1000W 35A X 3 RUB1.1600D 700W 1100W 1600W 40A X 4 RUB1.2500D 1000W 1700W 2500W 250A DIMENSIONS Length Height MODEL Width RUB1.1000D 390mm 205mm 60mm RUB1.1600D 450mm 205mm 60mm RUB1.2500D 580mm 205mm 60mm 4
ページ5に含まれる内容の要旨
TOOLS/PARTS FOR INSTALLATION NOTE: TOOLS ARE NOT SUPPLIED Small flat blade screwdriver phillips screwdriver (#2 or medium sized), Wire cutters, Wire strippers, - #6 round head screws, and 1 - #8 sheet metal screw (or nut, bolt flat washer, start washer) (see detail) 2 Ring connectors (large enough to accommodate your method of grounding) In-line fuse or Grommets (Sized to work with the power wire you plan to use in your installation) Tube of silicone seal. Protection Circuitry The amplifier pr
ページ6に含まれる内容の要旨
Electrical Wiring All RUBICON Amplifiers are equipped with easy top access screw terminals . These terminals are nickel-plated in order to ensure excellent electrical contact and to resist corrosion. When making electrical connections to the amplifier, please observe the following : Use at least 4 gauge or heavier wire for power and ground connections. Wire the amplifier directly to the car battery. Make sure there is circuit protection (Such as a fuse) on the positive power lead, within
ページ7に含まれる内容の要旨
PANEL LAYOUT RUB1.1000D LEFT VIEW Input Subsonic Low Pass Bass Line Out Line Input Level Filter Filter Boost PHASE L L PROTECTION 0 180 Min Max 10Hz 40Hz 50Hz 150Hz 0 +18dB Input Sensitivity Bridged Mode REMOTE DATALINK CONTROL .1V-2V 2V-8V Master Slave R R RIGHT VIEW BATT+ REMOTE GND POWER CONNECTIONS SPEAKER FUSES RUB1.1600D LEFT VIEW Input Subsonic Low Pass Bass Line Out Line Input Level Filter Filter Boost PHASE L L PROTECTION 0 180
ページ8に含まれる内容の要旨
PANEL LAYOUT RUB1.2500D LEFT VIEW Input Subsonic Low Pass Bass Line Out Line Input Level Filter Filter Boost PHASE L L PROTECTION 0 180 Min Max 10Hz 40Hz 50Hz 150Hz 0 +18dB Input Sensitivity Bridged Mode REMOTE DATALINK CONTROL .1V-2V 2V-8V Master Slave R R RIGHT VIEW SPEAKER POWER CONNECTIONS Class D Monoblock Amplifier Installation Wiring RUB1.1000D/RUB1.1600D/RUB1.2500D Low Level Inputs Input Subsonic Low Pass Bass Line Out Line Input Level Filter Filter Boost PHASE L L PR
ページ9に含まれる内容の要旨
Class D Monoblock Amplifier Installation Wiring RUB1.1000D/RUB1.1600D BATT+ REMOTE GND POWER CONNECTIONS SPEAKER FUSES RUB1.1600D has four fuses here BATT+ REMOTE GND POWER CONNECTIONS SPEAKER FUSES RUB1.1600D has four fuses here 9
ページ10に含まれる内容の要旨
Class D Monoblock Amplifier Installation Wiring RUB1.2500D SPEAKER POWER CONNECTIONS SPEAKER POWER CONNECTIONS 10
ページ11に含まれる内容の要旨
Bridging Two RUB1.1000D/RUB1.1600D/RUB1.2500D Amplifiers Input Subsonic Low Pass Bass Line Out Line Input Level Filter Filter Boost PHASE L L PROTECTION L 0 180 Min Max 10Hz 40Hz 50Hz 150Hz 0 +18dB Input Sensitivity Bridged Mode REMOTE DATALINK CONTROL .1V-2V 2V-8V R Master Slave R R Power min Max Subsonic Low Pass Bass Line Out Line Input Input Filter Filter Boost PHASE Level L L PROTECTION 0 180 Min Max 10Hz 40Hz 50Hz 150Hz 0 +18dB Bridged Input Sensitivi
ページ12に含まれる内容の要旨
Bridging Two RUB1.1000D/RUB1.1600D Amplifiers BATT+ REMOTE GND POWER CONNECTIONS SPEAKER FUSES RUB1.1600D has four fuses here BATT+ REMOTE GND POWER CONNECTIONS SPEAKER FUSES 12
ページ13に含まれる内容の要旨
Bridging Two RUB1.2500D Amplifiers SPEAKER POWER CONNECTIONS SPEAKER POWER CONNECTIONS 13
ページ14に含まれる内容の要旨
TROUBLE SHOOTING NO SOUND Is the LED lit? NO YES Check Power and Remote turn-on wire for voltage. Make sure Ground wire is secure. STILL NO SOUND See your Authorize Sound Stream Dealer. SOUND IN ONE CHANNEL ONLY Reverse left and right speakers by unplugging the speaker connector. turning it over and plugging it back in. SOUND IS NOW IN SAME CHANNEL OPPOSITE CHANNEL Reverse RCA inputs Problem is in the speaker of speaker wire of the silent channel SOUND IS NOW IN OPPOSITE CHANNEL SAME CHANNEL
ページ15に含まれる内容の要旨
Caution: Please do not plug in or unplug RCA Plugs to the amplifier inputs while the amplifier is turned on. Doing so is potentially harmful to the amplifier by allowing RF(radio frequencies) into the amplifier, causing instability, during the brief period while the RCA shield is not connected, and the hot is connected. Only plug in or unplug RCA plugs with the amplifier off as Standard practice with all audio equipment.
