ページ1に含まれる内容の要旨
S SB B- -P P- -C CY YN NNE NE/ /1 10W 0W6 6v v2 2/ /B BK K_ _IIN NS ST TR R_ _S SKU KU# #0 01 11 123 231 1
INSTALLATION
DIFFICULT Y:
If you choose to perform the installation yourself, it is absolutely vital that
®
OUT
the Stealthbox be properly mounted to the vehicle according to these
OF
instructions. Failure to mount the enclosure properly presents two problems:
INSTALL ATION GUIDE
for the 1) The sub-bass performance will suffer due to the movement of the enclosure
35
caused by the f
ページ2に含まれる内容の要旨
S SB B- -P P- -C CY YN NNE NE/ /1 10W 0W6 6v v2 2/ /B BK K_ _IIN NS ST TR R_ _S SKU KU# #0 01 11 123 231 1 STEP 4 STEP 8 Remove the bottom sill plate. Remove the upper d-pillar trim. STEP 5 STEP 9 Remove the lower d-pillar trim. With a T-30 socket, remove the bolt and metal bracket that is located between the two rear seats. STEP 6 STEP 10 Remove the top sill plate. Grab a hold of the back of the driver’s side rear seat as in the picture. Lift the right side of the seat up and out of the hi
ページ3に含まれる内容の要旨
S SB B- -P P- -C CY YN NNE NE/ /1 10W 0W6 6v v2 2/ /B BK K_ _IIN NS ST TR R_ _S SKU KU# #0 01 11 123 231 1 STEP 1 2 STEP 16 Remove the plastic collar that is around the hinge pin. Pull the SRS plastic badge from the upper c-pillar trim. With a T-25 socket, remove the bolt that has been exposed. STEP 1 3 STEP 17 Remove the trim panel. An airbag is located behind the c-pillar trim. Use caution while removing this panel. All wiring/connections should be protected. As in the illustration, r
ページ4に含まれる内容の要旨
S SB B- -P P- -C CY YN NNE NE/ /1 10W 0W6 6v v2 2/ /B BK K_ _IIN NS ST TR R_ _S SKU KU# #0 01 11 123 231 1 STEP 24 STEP 2 0 Found in the rearmost driver’s side floor corner, remove With a T-25 socket, remove three bolts that secures this the rubber grommet in the cargo area. rear side trim panel. Unsecure the wire harness from the wheel well. *Make sure the ignition is not turned on* Loosen the bolt that secures the brown wires to the flooring of the vehicle. Once loose, turn this wire a
ページ5に含まれる内容の要旨
S SB B- -P P- -C CY YN NNE NE/ /1 10W 0W6 6v v2 2/ /B BK K_ _IIN NS ST TR R_ _S SKU KU# #0 01 11 123 231 1 STEP 2 8 STEP 32 Fully thread the supplied coupler to the first socket cup set With a 9/16-inch socket and the remaining supplied pair of screw from STEP 27. bolt assemblies, secure the L-bracket to the Stealthbox®. Thread the second supplied socket cup set screw into the coupler. STEP 2 9 STEP 33 Place the Stealthbox® into position by guiding the socket From under the vehicle, place
ページ6に含まれる内容の要旨
S SB B- -P P- -C CY YN NNE NE/ /1 10W 0W6 6v v2 2/ /B BK K_ _IIN NS ST TR R_ _S SKU KU# #0 01 11 123 231 1 STEP 3 6 STEP 40 With a T-25 socket, secure the rear of the side trim panel With a T-25 socket, secure the top c-pillar trim to the to the d-pillar, from STEP 20. c-pillar, from STEPS 16 & 17. STEP 3 7 STEP 41 With a T-25 socket, secure the front of the side trim panel Secure the upper d-pillar trim to the d-pillar, secure the trim to the c-pillar, from STEP 18. with the mounting scre
ページ7に含まれる内容の要旨
S SB B- -P P- -C CY YN NNE NE/ /1 10W 0W6 6v v2 2/ /B BK K_ _IIN NS ST TR R_ _S SKU KU# #0 01 11 123 231 1 STEP 4 4 INC L UDED H A RD W A RE Replace the cargo door sill plate, from STEP 4. (2) (2) 3 3/ /8 8- -in inch - ch -1 16 x 2 1 6 x 2 1/ /4 4- -iin nch S ch So ocket C cket Cu up S p Se et S t Sc crew rews s (7) (7) 3/8 3/8- -iin nc ch h Fl Fla at t Wa Was sh he er r ( (1 1) ) 3 3/ /8 8- -in inch - ch -1 16 S 6 So ocket C cket Cu up S p Se et S t Sc crew C rew Co oup uplle er r (5) (5
