ページ1に含まれる内容の要旨
AD-C Series
AD-C820/AD-C821/ AD-C1200 User Manual
AD-C820 – 203 mm (8") 2-way coax baffle assembly
AD-C800BB – Pre-install enclosure for AD-C820
AD-C821 – 203 mm (8") 2-way coax blind-mount
AD-C800 RAIL KIT – Split Ring and Tile Rails for AD-C821
AD-C800RG – Round Grille for 8" loudspeaker
AD-C800SG – Square Grille for 8" loudspeaker
AD-C1200 – 304 mm (12") 2-way coax baffle assembly
AD-C1200BB – Pre-install enclosure for AD-C1200
AD-C1200SG – Square Grille for 12" loudspeaker
TD-000296-
ページ2に含まれる内容の要旨
IMPORTANT SAFETY PRECAUTIONS AND EXPLANATION OF SYMBOLS WARNING! 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Clean only with a dry cloth. 6. Install in accordance with QSC Audio Product’s instructions and local building codes. The installation should be done by a licensed installation professional. 7. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) tha
ページ3に含まれる内容の要旨
Introduction Congratulations and thank you for your ceiling loudspeaker purchase. The AD-C820, AD-C821 and AD-C1200 models offer excellent acoustic performance in an easy-to-install and attractive package. Please review these instructions carefully and follow the recommendations. Installation should be done by a licensed installation professional and in accordance with these instructions and local building codes. The AD-C820 and AD-C821 models feature an 8" coaxial driver with a high-frequency
ページ4に含まれる内容の要旨
Features AD-C821 Loudspeaker System d c e b a – Figure 1 – f g h – Figure 2 – a. Pivoting connection cover b. Euro connectors c. Pivoting connection cover retaining screw d. Loudspeaker wiring hole e. Seismic mounting tab f. Mounting tabs g. Grille attachment magnets h. Tap switch (transformer included) 3 4
ページ5に含まれる内容の要旨
AD-C820 Loudspeaker Baffle a b c a. Mounting tabs – Figure 3 – b. Grille attachment magnets c. Tap Switch (transformer included in AD-C800BB) AD-C800BB Back Box Sold separately for use with AD-C820 Loudspeaker Baffle a a b a c e a d a – Figure 4 – a. Dual Knockouts (½" and ¾") (Qty: 5) b. Ceramic terminal block c. Transformer d. Mounting straps (Qty: 4) e. Ten-pin Mate-N-Lok™ 3 4
ページ6に含まれる内容の要旨
AD-C800 Rail Kit The AD-C800 RAIL KIT is sold separately for use with the AD-C821 loudspeaker system. – Figure 5 – – Figure 6 – Split Ring Suspended-ceiling Tile Rail AD-C800SG/RG Loudspeaker Grilles Sold separately for use with the AD-C820 and AD-C821 loudspeaker systems – Figure 7 – – Figure 8 – AD-C800RG AD-C800SG 5 6
ページ7に含まれる内容の要旨
AD-C1200 Loudspeaker Baffle a c b d – Figure 9 – a. Dual Euro connectors b. 150 W Transformer for 70/100 V distributed loudspeaker systems c. Crossover network d. Installation hook AD-C1200BB Back Box Sold separately for use with AD-C1200 Loudspeaker Baffle b a a a a c a – Figure 10 – a. Dual knockouts (½" and ¾") (Qty: 5) b. Mounting tabs (Qty: 4) c. Ceramic terminal block 5 6
ページ8に含まれる内容の要旨
AD-C1200SG Loudspeaker Grille – Figure 11 – AD-C821 Installation Options The AD-C821 Loudspeaker System is a blind-mount design made to mount into finished ceilings. The AD-C821 loudspeaker system can be mounted in suspended ceilings, as well as non-suspended ceiling types. We recommend that you consult an installation professional for safety assurance, quality installation, and optimum acoustic performance. Suspended Ceiling The Suspended-ceiling Tile Rails (Figure 6) must be used with the
ページ9に含まれる内容の要旨
AD-C821 Installation Tools and Parts Required for Installation 1. #2 Phillips head screwdriver 2. Torque driver 3. Wire stripping tool 4. Soldering equipment 5. Tool for cutting loudspeaker mounting hole in ceiling. Must be able to cut a circular hole through the ceiling without damaging the structural integrity of the ceiling. 6. Small flat-tip screwdriver for securing wires in Euro-style connector. 7. Wire Clamp Fitting to install in the cover plate loudspeaker wiring hole to protect and sta
ページ10に含まれる内容の要旨
15.16" 395 mm – Figure 12 – Install Split Ring and Suspended-ceiling Tile Rails 1. Skip this step if installing in a non-suspended ceiling. Pass the two Suspended-ceiling Tile Rails (Figure 6) through the hole and place on both sides of the mounting hole 15.16" (395 mm) apart, as shown in (Figure 12) and install onto the ceiling T-rails. Make sure the bottom part of the bracket (that is flat against the tile) is toward the mounting hole and the vertical rail of the support bracket (with the
ページ11に含まれる内容の要旨
Support and Wire the Loudspeaker System Important: Loudspeakers can potentially generate substantial vibration. In addition to ensuring all hardware is properly installed and secure, you must use the Seismic Support Bracket on the loudspeaker to secure the loudspeaker to an appropriate structural support. This minimizes the chance of the loudspeaker falling from the ceiling in the event the primary mount fails. Any cable or wire used as a secondary support line must be strong enough to suppor
ページ12に含まれる内容の要旨
AD-C800BB and AD-C820 Installation The AD-C800BB is designed to be pre-installed into the ceiling and wired. The AD-C820 Loudspeaker Baffle assembly is plugged into and secured to the back box at a later time. AD-C800BB Back Box Installation The AD-C800BB installation should be done by a licensed installation professional and wiring installed by a licensed electrician in accordance with local building codes. 1. There are 5 wiring ½" & ¾" knockout locations, shown as item a (Figure 16), avail
ページ13に含まれる内容の要旨
d c b – Figure 17 – a a. Facility’s loudspeaker signal wiring b. Ceramic terminal block c. Wiring to loudspeaker baffle d. Wire holding screws AD-C820 Installation 1. Connect the 10-pin Mate-N-Lok™ connector from the AD-C800BB to J1 on the transformer tap switch PCB. 2. Connect the 3 Faston connectors to the crossover points J2, J3, and J4 on the larger PCB. Note: J2, J3, and J4 are labeled for the proper wire color. If the wire colors on the harness are different than the labels, one connecto
ページ14に含まれる内容の要旨
70V Mount the AD-C820 or AD-C821 Loudspeaker System Note: The Mounting Clamps are part of the assembly and allow for mounting surfaces (ceiling) up to 2.75" in thickness. Do not install the grille until clamps have been tightened and any adjustments made. 1. Before inserting the loudspeaker into the mounting hole or AD-C-800BB back box, adjust the Mounting Clamps counterclockwise, using a Phillips screwdriver, so they are folded in against the loudspeaker backcan and provide enough space for
ページ15に含まれる内容の要旨
2. Make sure all tests and adjustments are complete before installing the grille. 3. Locate the loudspeaker grille. 4. The loudspeaker system and grille both have a Grille-retaining Safety Tether. Using the clip on the grille’s tether, attach the grille’s safety tether to the loudspeaker’s safety tether. Refer to (Figure 22) for details regarding the clip. a b – Figure 21 – – Figure 22 – a. Loudspeaker tether b. Grille tether a b b c a – Figure 23 – a. Holes for mounting grille with screws (4
ページ16に含まれる内容の要旨
AD-C1200 and AD-C1200BB Installation The AD-C1200BB back box is designed to be pre-installed into the ceiling and wired. The AD-C1200 Loudspeaker Baffle assembly is plugged into and secured to the back box at a later time. AD-C1200BB Installation The AD-C1200BB installation should be done by a licensed installation professional and wiring installed by a licensed electrician in accordance with local building codes. 1. There are 5 wiring ½" & ¾" knockout locations available on the AD-C1200BB
ページ17に含まれる内容の要旨
d c b a – Figure 24 – a. Facility's loudspeaker signal wiring b. Ceramic terminal block c. Wiring to loudspeaker d. Wire holding screws AD-C1200 Installation Note: AD-C1200 comes pre-wired, from the factory, for transformer tap applications. To bypass the transformer see “Remove Transformer from the AD-C1200 Circuitry” in this section. 1. Locate and remove the five-pin Euro-style connector plug included with the loudspeaker baffle assembly. Typically it is plugged into its mate (J2) on the
ページ18に含まれる内容の要旨
– Figure 25 – 1. Tighten the M3 wire retaining screws. 2. Reconnect the five-pin Euro-style connector plug into its mate on the PCB. Make sure all connections are secure. Caution: The AD-C1200 Loudspeaker Baffle assembly weighs 25 lbs (11.3 kg.) Be sure to use proper safety precautions. 3. Lift the loudspeaker baffle assembly into back box enclosure. There are arrows (b) on the baffle assembly indicating which edge is inserted first and the location of the installation hook. (a) Use the install
ページ19に含まれる内容の要旨
a b a a a a a c – Figure 27 – a. Baffle mounting holes — 6 places b. Grille mounting holes — 4 places c. Extra mounting holes — 4 places 5. Locate the loudspeaker’s grille. 6. Using a #2 Phillips head screwdriver, install the grille with the M4 screws provided. ® Note: The use of LOCTITE is recommended to prevent grille screws from loosening during use. Note: The extra mounting holes, shown as item c (Figure 27), are to be used with previously installed enclosures from other manufacturer
ページ20に含まれる内容の要旨
Disconnect Transformer from the AD-C1200 Circuitry If you are connecting the loudspeaker to a 16 ohm system, you must disconnect the transformer. 1. Unplug the two-pin Euro-style plug (J1) on the PCB (Figure 25). 2. Loosen the two M3 wire securing screws using a #1 Phillips head screwdriver and remove the wires. 3. Secure and insulate all the wires you removed using a tie-wrap or similar device. This is to prevent rattling during loudspeaker operation. 4. Insert the wires from the back box cera
