ページ1に含まれる内容の要旨
Edition:2006/1/10
Air Conditioner
OPERRATION
ページ2に含まれる内容の要旨
Edition:2006/1/10 Air Conditioner Cautions Disposal of the old air conditioner Safety Instructions and Warnings Before disposing an old air conditioner that Before starting the air conditioner, read the hoes out of use, please make sure it's inop- information given in the User's Guide caref- erative and safe. Unplug the air conditioner ully. The User's Guide contains very impor- in order to avoid the risk of child entrapment. tant observations relating to the assembly, operation and maintenance
ページ3に含まれる内容の要旨
Edition:2006/1/10 Air Conditioner Cautions Do not obstruct or cover the ventilation 7. The appliance is not intended for use grille of the air conditoner.Do not put fingers by young children or infirm persons or any other things into the inlet/outlet and without supervision. swing louver. 8. Young children should be supervised to ensure that they do not play with Do not allow children to play with the air the applience. conditioner.In no case should children be allowed t
ページ4に含まれる内容の要旨
Edition:2006/1/10 Air Conditioner Cautions Safety Instruction Please read the following Safety Instructions carefully prior to use. The instructions are classified into two levels, WARNING and CAUTION according to the seriousness of possible risks and damages as follows. Compliance to the instructions are strictly required for safety use. Installation WARNING Please call Sales/Service Shop for the Installation. Do not attempt to install the air conditioner by yourself because improper works may
ページ5に含まれる内容の要旨
Edition:2006/1/10 Air Conditioner Cautions WARNING When abnormality such as burnt-small found, Use an exclusive power source with a immediately stop the operation button and circuit breaker contact sales shop. STRICT OFF ENFORCEMENT Connect power supply cord Use the proper voltage Do not use power supply cord to the outlet completely extended or connected in halfway STRICT STRICT PROHIBITION ENFORCEMENT ENFORCEMENT Take care not to damage Do not insert objects into the air Do not use power sup
ページ6に含まれる内容の要旨
Edition:2006/1/10 Air Conditioner Parts and Functions Indoor unit OPERATE COOL DRY HEAT TIMER HEALTH Display board RED GREEN GREEN GREEN YELLOW RED The conversion of pilot light's colors will be displayed as the figure under different operation models Display board Inlet Air filter (inside) Anion generator (inside) Inlet grille Vertical flap (Use remote controller to adjust up and down air flow. Don't adjust it manually) Horizontal louver (adjust left and right air flow) Outdoor unit 3 CONNECTIN
ページ7に含まれる内容の要旨
Edition:2006/1/10 Air Conditioner Parts and Functions 19 10. ON/OFF button Used for unit start and stop. 11. TIMER ON display 12. FAN SPEED display LOW HI MED AUTO 13. LOCK display 14. SWING UP/DOWN display 15. SLEEP display 28 16. HEALTH display POWER/SOFT 17. Operation mode display Operation mode AUTO COOL DRY FAN HEAT 30 Remote controller 18.Singal sending display 19. POWER/SOFT display 20. Left/right air flow display 21. TEMP display Remote controller: to display the TEMP. setting. 1.CODE
ページ8に含まれる内容の要旨
Edition:2006/1/10 Air Conditioner Parts and Functions Clock Set When unit is started for the first time and after replacing batteries in remote controller, clock should be adjusted as follows: 1. Press CLOCK button,"AM" or "PM" flashes. POWER/SOFT 2. Press or to set correct time. Each press will increase or decrease 1 min. If the button is kept depressed, time will change quickly. 3. After time setting is confirmed, press SET, "AM" or "PM" stop flashing, while clock starts working.
ページ9に含まれる内容の要旨
Edition:2006/1/10 Air Conditioner Operation HEALTH operation Remote controller 1.Unit start Press ON/OFF on the remote controller, unit starts. Health function includes health anion function, UV light degerming function. 2.Health anion function Press HEALTH button. For each press, is displayed. Air conditioner starts health anion function operation. For twice press, disappears,the operation stops. When indoor fan motor is running, it has healthy process function. (It's available un
ページ10に含まれる内容の要旨
Edition:2006/1/10 Air Conditioner Operation Auto Operation 1. Unit start Remote controller Press ON/OFF on the remote controller, unit starts. 2.Select operation mode Press MODE button. For each press, operation mode changes as follows: Remote controller: AUTO COOL DRY FAN HEAT Then Select Auto operation 3.Select temp.setting Press TEMP. button Every time the button is pressed, temp.setting increase 1oC,if kept depressed, it will increase rapidly POWER/SOFT Every time the button is pressed, tem
ページ11に含まれる内容の要旨
Edition:2006/1/10 Air Conditioner Operation Cool Operation 1. Unit start Remote controller Press ON/OFF on the remote controller, unit starts. 2.Select operation mode Press MODE button. For each press, operation mode changes as follows: Remote controller: AUTO COOL DRY FAN HEAT Then Select COOL operation 3.Select temp.setting Press TEMP. button Every time the button is pressed, temp.setting increase 1oC,if kept depressed, it will increase POWER/SOFT rapidly Every time the button is pressed, tem
ページ12に含まれる内容の要旨
Edition:2006/1/10 Air Conditioner Operation Dry Operation Remote controller 1. Unit start Press ON/OFF on the remote controller, unit starts. 2.Select operation mode Press MODE button. For each press, operation mode changes as follows: Remote controller: AUTO COOL DRY FAN HEAT Then Select DRY operation 3.Select temp.setting Press TEMP. button Every time the button is pressed, temp.setting increase 1oC,if kept depressed, it will increase POWER/SOFT rapidly Every time the button is pressed, temp.
ページ13に含まれる内容の要旨
Edition:2006/1/10 Air Conditioner Operation Fan Operation 1. Unit start Remote controller Press ON/OFF on the remote controller, unit starts. 2.Select operation mode Press MODE button. For each press, operation mode changes as follows: Remote controller: AUTO COOL DRY FAN HEAT Then Select FAN operation 3.Fan speed selection Press FAN button. For each press, fan speed changes as follows: Remote controller: LOW POWER/SOFT MED HI 4.Unit stop Press ON/OFF button, the unit stops. About FAN operation
ページ14に含まれる内容の要旨
Edition:2006/1/10 Air Conditioner Operation Heat Operation 1. Unit start Press ON/OFF on the remote controller, unit starts. Remote controller 2.Select operation mode Press MODE button. For each press, operation mode changes as follows: Remote controller: AUTO COOL DRY FAN HEAT Then Select HEAT operation 3.Select temp.setting Press TEMP. button Every time the button is pressed, temp.setting increase 1oC,if kept depressed, it will increase rapidly Every time the button is pressed, temp.setting P
ページ15に含まれる内容の要旨
Edition:2006/1/10 Air Conditioner Operation Air Flow Direction Adjustment 1.Status display of air sending Vertical flap Pos.1 Pos.2 Pos.3 Pos.4 POWER/SOFT Pos.5 Pos.6 (Auto swing) 2.Up and down air flow direction For each press of button, air flow direction on remote controller displays as follows according to different operation modes: COOL/DRY/FAN remote controller: Pos.1 Pos.2 Pos.3 Pos.4 Pos.6 : HEAT: remote controller: Pos.5 Pos.4 Pos.3 Pos.2 Pos.1 Pos.6 AUTO: Pos.1 Pos.2 Pos.3 Pos.
ページ16に含まれる内容の要旨
Edition:2006/1/10 Air Conditioner Operation Sleep Operation SLEEP operation starts SLEEP operation stops Approx.6hrs Before going to bed, you can simply press the SLEEP button and unit will operate in SLEEP Rises 1OC 1 hr mode and bring you a sound sleep. Use of SLEEP function Rises 1OC 1 hr After the unit starts, set the operation status, then press SLEEP button before which the Unit stop Temp.setting clock must be adjusted and time being set. In COOL, DRY mode Operation Mode 1. In COOL,DRY mod
ページ17に含まれる内容の要旨
Edition:2006/1/10 Air Conditioner Operation Timer On/Off Operation Set clock correctly before starting TIMER operation. 1. After unit starts, select your desired operation mode. Remote Controller 2. Timer mode selection Press TIMER button to change TIMER mode. Every time the button is pressed, display changes as follows: Remote controller: BLANK TIMER ON TIMER OFF TIMER ON-OFF Then select your desired TIMER mode (TIMER ON or TIMER OFF). " "or " "will flash. 3.Time settin
ページ18に含まれる内容の要旨
Edition:2006/1/10 Air Conditioner Operation Timer On-Off Operation Set clock correctly before starting TIMER operation. Remote Controller 1. After unit starts, select your desired operation mode 2. Timer mode selection Press TIMER button to change TIMER mode. Every time the button is pressed, display changes as follows: Remote controller: BLANK TIMER ON TIMER OFF TIMER ON-OFF Then select your desired TIMER mode (TIMER ON - OFF). " "will flash. 3.Time setting Press HOUR
ページ19に含まれる内容の要旨
Edition:2006/1/10 Air Conditioner Operation POWER/SOFT Operation POWER Operation When you need rapid heating or cooling, you can use this function. Remote controller Selecting of POWER operation Press POWER/SOFT button. Every time the button is pressed,display changes as follows: BLANK POWER SOFT Stop the display at In POWER operation status: In COOL mode, wind speed automatically takes high wind of AUTO wind mode. In HEAT mode, wind speed automatically takes medial wind of AUTO wind mode. To ca
ページ20に含まれる内容の要旨
Edition:2006/1/10 Air Conditioner Operation Health airflow Operation 1.Press ON/OFF to starting Remote controller The liquid crystal will display the working state of last time (Except timer, sleeping, power/soft and health airflow). Setting the comfort work conditions. 2.The setting of health airflow function 1).Press the button of health airflow, appears on the display. The nether inlet and outlet grills of the air condit- ioner are closed and the airflow is blown horizontally from the
