ページ1に含まれる内容の要旨
SD1411
Owner's Manual
AM/FM/CD/MP3/WMA Receiver
SD1411 MP3/WMA RECEIVER
MONO
TUNE
EQ
/
AUX IN
SCAN
MENU
(7)
ページ2に含まれる内容の要旨
SD1411 PREPARATION Getting Started make sure the kit works with your vehicle. If you need a kit but cannot locate one, call our Congratulations on your purchase of the Phase Disconnect Battery customer support line at 1-800-323-4815. Linear SD1411 Mobile AM/FM/CD/MP3/WMA Before you begin, disconnect the battery (U.S.A. and Canada only.) Receiver. It’s a good idea to read all of the negative terminal. instructions before beginning the installation. Tools and Supplies We recommend having y
ページ3に含まれる内容の要旨
/ MONO CD1211 CD RECEIVER TUNE EQ / SCAN AUX IN CD1211 CD RECEIVER MONO TUNE EQ SCAN AUX IN SD1411 INSTALLATION INSTRUCTIONS This unit is designed for installation in cars, Universal Installation Using trucks and vans with an existing radio opening. Mounting Sleeve In many cases, a special installation kit will be 1. Remove the detachable front panel, if it is required to mount the radio to the dashboard. attached to the chassis, by pushing the These kits are available at electronics supp
ページ4に含まれる内容の要旨
SD1411 9. Attach one end of the perforated support 2. Install the radio/mounting plate assembly Longer screws may damage components strap (supplied) to the screw stud on the to the sub-dashboard according to the inside the chassis. rear of the chassis using the hex nut instructions in the installation kit. provided. Fasten the other end of the 3. Attach the support strap to the radio and perforated strap to a secure part of the dashboard as described in the Universal dashboard, either above o
ページ5に含まれる内容の要旨
SD1411 Remove Radio To remove the radio after installation, remove the trim ring by lifting in the center and pulling it off from either side. Insert the removal keys straight back until they lock, and then pull the radio out. If removal keys are inserted at an angle, they will not lock properly to release the unit. Removal Key 5
ページ6に含まれる内容の要旨
15 SD1411 WIRING 1. Power Antenna (dark blue wire) - Connect to power antenna or amplifier. If not used, Yellow tape bare end of wire. 2. Accessory/Ignition (red wire) - Connect to existing radio wire or radio fuse. 3. Ground (black wire) - Connect to ground 5 terminal or clean, unpainted part of chassis. 4. Memory/Battery (yellow wire) - Connect to battery or 12 volt power source that is 11 Dark Blue always live. The radio will not work if this 1 wire is not connected. 5. Antenna Connec
ページ7に含まれる内容の要旨
SD1411 OPERATING INSTRUCTIONS Power Select clockwise or counter clockwise to adjust the bass from “-10” to “+10”. “00” represents a flat Press the power button (1) or any other button Press the AUDIO CONTROL button (4) to step response. The bass level is shown on the on the face of the receiver to turn the unit on through the menu of audio functions: volume display for five seconds or until another function when the ignition switch is on. Press the power (VOL), bass (BAS), treble (TRB), ba
ページ8に含まれる内容の要旨
T T T T C C C C L L L L E E E E E E E E S S S S H H H H S S S S PU PU PU PU SD1411 Balance X-BASS (BAND) Equalizer Selector (EQ) Press the AUDIO CONTROL button (4) four Press and hold the BAND button (5) for two The equalizer function applies preset sound times until “BAL” appears in the display. Within seconds to activate the X-BASS feature. When effects to the unit’s audio output signal. Press five seconds, turn the AUDIO CONTROL (3) listening to music at low volume levels, this EQ (20) t
ページ9に含まれる内容の要旨
SD1311 MP3/WMA RECEIVER MONO TUNE EQ / SCAN AUX IN MENU (7) SD1411 Display (D) Front Panel Release that it is correctly engaged, then lightly press the left side of the panel until the mechanism When the unit is off, the LCD displays the time The front panel release button (10) releases the locks it into place. of day. When the unit is on, the LCD mechanism that holds the front panel to the automatically shows the tuner or CD display, chassis. Reset Button depending on which mode of operati
ページ10に含まれる内容の要旨
SD1411 TUNER OPERATION AM/FM Band Selector (BAND) Scan Tuning (SCAN) Preset Stations Press BAND (5) during radio play to switch Press SCAN (15) to scan upwards through all Up to six stations on each band can be stored between three FM bands and one AM band. the strong channels in the current band. The as presets and can then be instantly recalled by “F1”, “F2”, “F3” or “AM” will appear in the unit will pause and play each station for five pressing the associated preset button on the display t
ページ11に含まれる内容の要旨
SD1411 Repeat for the remaining five presets on the Mono/Stereo Selector (MONO) current band and for all presets on the other Press MONO (18) during FM radio operation to three bands. select stereo reception of the broadcast signal. Under normal reception, the unit should be left Automatically Store / Preset in the stereo mode as indicated by the “ST” Scan (AS/PS) designation and the associated signal strength Automatically Store indicator that appear on the display panel when Select six
ページ12に含まれる内容の要旨
SD1411 CD PLAYER OPERATION Insert CD During either function, the elapsed time will Disc Scan (SCN) appear on the display. Release the button to With the label surface facing up, gently insert During disc play, press SCN (24) to play the resume CD play. the disc into the CD slot (21) until the soft- first 10 seconds of each track on the disc. “S-- loading mechanism engages and pulls the disc SCN” will appear in the display. When the Play/Pause in. Disc play begins, “CDP PLAY” will appear in de
ページ13に含まれる内容の要旨
SD1411 Disc Repeat (RPT) CD Player Error Codes Press RPT (25) during disc play to continuously If a problem should develop while operating the repeat the selected track. “S--RPT” will appear CD player, an error code (ER-1, ER-2, etc.) in the display. Press RPT again to stop may appear on the display panel. This can repeating. “S--RPT” will disappear from the indicate a number of problems with the unit, display, and regular play will resume. The including a mechanical error or an error in the
ページ14に含まれる内容の要旨
SD1411 MP3/WMA OPERATION MP3 and WMA (Windows Media Audio) music Acceptable Medium Formats MP3/WMA Encoder and CD files are digital audio files that are compressed Writer Settings The following formats are available for the to allow more files on a single CD. This unit can media used in this unit. The maximum number Use the following settings when compressing play MP3/WMA directly from files contained on of characters used for file name including the audio data in MP3 data with the MP3 e
ページ15に含まれる内容の要旨
28 27 SD1411 Entering ID3 Tag Writing Files into a Medium Electronic Shock Protection • 10 seconds for CDDA (CDA) This unit supports ID3 tag versions 1.0 and 1.1. When a medium containing MP3/WMA data is For the character codes, refer to the table loaded, the unit checks all data. If the medium • 100 seconds for MP3/WMA recorded at contains many folders or non-MP3/WMA files, below. 44.1kHz, 128kbps MP3/WMA play will be delayed, it may take Bit Rates time for the unit to move to the next fil
ページ16に含まれる内容の要旨
SD1411 beginning with play sequence numbers such as Track Select Direct File Number Search "01" to "99". Press the AS/PS button (17) to enter Direct Press the Up Tuning (14) or Down Tuning (13) For example, a medium with the following Track Search mode. The LCD will display "MP3 button for less than one second to advance to folder/file hierarchy is subject to Folder Search, T" followed by a blinking asterisk. Refer to the the next track on the disc, or press and hold to File Search or Fol
ページ17に含まれる内容の要旨
SD1411 You can also turn the rotary to access and file LCD will display the first folder or file name • Select the folder icon to return to the numbers sequentially. After locating the desired in the root directory. previous file level and select a file, press the BAND/ENTER button (5) or 5. Turn the AUDIO CONTROL (3) to browse different directory or file. AUDIO CONTROL button (4) to begin all available folder or files in the root Display Information playback. directory. Press the D button (
ページ18に含まれる内容の要旨
SD1411 USING A USB DEVICE OR SD CARD Loading a USB Device your SD Card as illustrated below and then reinstall the front panel. USB devices can be played through the USB connector on the front panel. To access files on a USB device, insert the USB device as indicated below: RESET SD1411 MP3/WMA RECEIVER MONO TUNE EQ / AUX IN SCAN (7) MENU After inserting an SD card containing MP3 or WMA files, “SD Play” appears on the display and the unit will automatically scan the card for music files
ページ19に含まれる内容の要旨
SD1411 REMOTE CONTROL The remote control will allow you to control the basic functions of the SD1411. The remote control sensor is located on the left side of the front panel to the right of the MONO button (18). S AMS = AS/PS VOL PEQ = EQ MOD = MODE VOL LOC = Local/Distant BND = BAND D U LOUD TR. UP TR. DN SCN = Scan, AM, FM BND SCN MOD MUT = MO = MONO LOC AMS PEQ DISP = Clock/Frequency MO MUT DISP PAU SCN RPT 12 3 5 4 6 SHUF DN UP 19
ページ20に含まれる内容の要旨
SD1411 CARE AND MAINTENANCE CD Player Compact Discs CDs, as they can irreparably damage the disc’s surface. CD-R and CD-RW Capability The following guidelines will help you extend 3. Discs should be kept in their storage the life of your CD player: Depending on media type and method of cases when not in use. "recording/burning", some CD-R/RWs may be 1. When cleaning the vehicle interior, do not 4. Do not expose discs to direct sunlight, incompatible with this unit. After "recording/ get w
