ページ1に含まれる内容の要旨
JMD200
AM/FM/CD AUDIO SYSTEM
Installation and Operation Manual
INT
PUSH POWER
ページ2に含まれる内容の要旨
JMD200 CONTENTS System Features ................................................................................................. 1 Safety Information .............................................................................................. 2 Installation........................................................................................................... 3 Basic Operation .................................................................................................. 6 Tuner Operati
ページ3に含まれる内容の要旨
JMD200 SYSTEM FEATURES Features of the Jensen JMD200 mobile audio system include: • AM/FM Tuner with 30 Presets (12 AM, 18 FM) • Single In-Dash CD Player •Mute • Electronic Bass, Treble, Balance and Fader Controls •Clock Content List • Jensen Main Chassis • Hardware Kit • Wiring Harnesses (4-pin and 9-pin) • Installation Manual Hardware Kit 1AMP FLANGE NUTS 10 AMP MOUNTING STRAP DIN SLEEVE REMOVAL TOOL MOUNTING SCREW MOUNTING BUSHING 1
ページ4に含まれる内容の要旨
JMD200 SAFETY INFORMATION When Driving Disc Maintenance Keep the volume level Iow enough to be aware of the road and traffic conditions. • A dirty or defective disc may cause sound dropouts while playing. Before playing, wipe When Washing your Vehicle the disc using a clean cloth, working from the center hole towards the outside edge. Never use benzene, thinners, cleaning fluids, anti-static liquids or any other solvent. Do not expose the product to water or excessive moisture. Moisture can ca
ページ5に含まれる内容の要旨
INT JMD200 INSTALLATION to a secure part of the dashboard, either above or below the radio using the screw and Before You Begin flange nut provided. Bend the strap to position it as necessary. 1. Disconnect Battery Before you begin, always disconnect the battery negative terminal. CAUTION: The rear of the radio must be supported with either the perforated strap or 2. Remove Transport Screws the rubber mounting bushing to prevent damage to the dashboard from the weight of the radio or imprope
ページ6に含まれる内容の要旨
JMD200 Wiring Diagram 4
ページ7に含まれる内容の要旨
JMD200 Reconnecting the Battery When wiring is complete, reconnect the battery negative terminal. Removing the Unit To remove the radio after installation, insert the removal keys straight back until they click, and then pull the radio out. If removal keys are inserted at an angle, they will not lock properly to release the unit. 5
ページ8に含まれる内容の要旨
JMD200 BASIC OPERATION NOTE: CD mode will be skipped if no CD is inserted. Reset Use a ball point pen or thin metal object to press the RESET button (11). The reset button should be activated for the following reasons: • initial installation of the unit when all wiring is completed INT LOUD • function buttons do not operate • error symbol on the display PUSH POWER Audio Menu With the radio on, press the SEL button/rotary encoder (1) on the control panel to access the audio menu. You can naviga
ページ9に含まれる内容の要旨
JMD200 Time/Frequency Display Selector (T/F) Displaying the Clock Press the T/F button (10) to display the time of the incorporated quartz clock for 5 seconds. Setting the Clock 1. To set the clock, first turn the vehicle ignition and radio on. 2. Press and hold the T/F button (10). 3. Press the TUNE/TRK |<< and >>| buttons (4) to adjust the hours. “AM” or “PM” will appear on the display to indicate AM or PM. 4. Press the T/F button again to move the cursor to the minutes position, and then
ページ10に含まれる内容の要旨
JMD200 TUNER OPERATION Select a Band Automatically Store / Preset Scan (A/PS) Press the BND button (3) to change between three FM bands and two AM bands. Automatically Store • During FM operation, when the station is broadcasting in stereo, the stereo icon ( ) Select an AM or FM band. Press and hold the A/PS button (5) for more than 2 seconds to appears on the display. automatically select six strong stations and store them in the current band. The new stations • During AM operation, no indica
ページ11に含まれる内容の要旨
JMD200 CD PLAYER OPERATION Inserting and Ejecting a Disc Controlling Disc Playback Insert a disc, label-side up, into the disc slot (7). The unit will automatically draw the disc in and Selecting Tracks play the first track on the disc, whether the power was turned on or not. Press the TUNE/TRK >>| or |<< button (4) to advance to the next track on the disc. The selected track number will appear on the display. Press the eject button (9) to stop disc play and eject the disc. The unit will rev
ページ12に含まれる内容の要旨
JMD200 CARE AND MAINTENANCE TROUBLESHOOTING • Keep the product dry. If it does get wet, wipe it dry immediately. Liquids might contain minerals that can corrode the electronic circuits. Symptom Cause Solution • Keep the product away from dust and dirt, which can cause premature wear of parts. No power The vehicle’s accessory If the power supply is properly • Handle the product gently and carefully. Dropping it can damage circuit boards and switch is not on connected to the vehicle’s acces- ca
ページ13に含まれる内容の要旨
JMD200 SPECIFICATIONS CD Signal to Noise Ratio. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . > 55 dB Channel Separation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .: More than 50 dB Frequency Response . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . : 20 Hz - 20 kHz FM Radio Frequency Coverage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ページ14に含まれる内容の要旨
ASA Electronics Corporation www.asaelectronics.com © 2007 ASA Electronics Corporation v.080207
