ページ1に含まれる内容の要旨
SPLIT TYPE ROOM AIR CONDITIONER
OPERATION MANUAL
HSM09HS03/R2(DB)
HSM09HS03/R2(DB)
2HUM18H03/R2(DB)
HSM09HS03/R2(DB)
HSM12HS03/R2(DB)
2HUM18H03/R2(DB)
Please read this operation manual before using the air conditioner
No.0010557181
ページ2に含まれる内容の要旨
Cautions Disposal of the old air conditioner Safety Instructions and Warnings Before disposing an old air conditioner that Before starting the air conditioner, read the goes out of use, please make sure it's inop- information given in the User's Guide caref- erative and safe. Unplug the air conditioner ully. The User's Guide contains very impor- in order to avoid the risk of child entrapment. tant observations relating to the assembly, operation and maintenance of the air conditioner. It must be
ページ3に含まれる内容の要旨
Cautions 7. The appliance is not intended for use Do not obstruct or cover the ventilation by young children or infirm persons grille of the air conditoner.Do not put fingers without supervision. or any other things into the inlet/outlet and swing louver. 8. Young children should be supervised to ensure that they do not play with Do not allow children to play with the air the applience. conditioner.In no case should children be allowed to sit on the outdoor unit. 9.Ple
ページ4に含まれる内容の要旨
Cautions Safety Instruction Please read the following Safety Instructions carefully prior to use. The instructions are classified into two levels, WARNING and CAUTION according to the seriousness of possible risks and damages as follows. Compliance to the instructions are strictly required for safety use. Installation WARNING Please call Sales/Service Shop for the Installation. Do not attempt to install the air conditioner by yourself because improper works may cause electric shock, fire, water
ページ5に含まれる内容の要旨
Cautions Safety Instruction Please read the following Safety Instructions carefully prior to use. The instructions are classified into two levels, WARNING and CAUTION according to the seriousness of possible risks and damages as follows. Compliance to the instructions are strictly required for safety use. Installation WARNING Please call Sales/Service Shop for the Installation. Do not attempt to install the air conditioner by yourself because improper works may cause electric shock, fire, water
ページ6に含まれる内容の要旨
Parts and Functions Indoor unit OPERATE COOL DRY HEAT TIMER HEALTH Display board RED GREEN GREEN GREEN YELLOW RED The conversion of pilot light's colors will be displayed as the figure under different operation models Display board Inlet Air filter (inside) Anion generator (inside) Inlet grille Vertical flap (Use remote controller to adjust up and down air flow. Don't adjust it manually) Horizontal louver (adjust left and right air flow) For multi-split type, the power plug is on the outdoor uni
ページ7に含まれる内容の要旨
Parts and Functions 19 9. HEALTH button Used to set healthy operation. 10. ON/OFF button Used for unit start and stop. 11. TIMER ON display 12. FAN SPEED display LOW HI MED AUTO 13. LOCK display 28 FRESH 14. SWING UP/DOWN display 15. SLEEP display 16. HEALTH display POWER/SOFT 17.FRESH AIR display 18. Operation mode display Operation mode AUTO COOL DRY HEAT FAN 33 Remote controller 19.Singal sending display 20. POWER/SOFT display 21. Left/right air flow display 22. TEMP display Remote control
ページ8に含まれる内容の要旨
Parts and Functions Clock Set When unit is started for the first time and after replacing batteries in FRESH remote controller, clock should be adjusted as follows: 1. Press CLOCK button,"AM" or "PM" flashes. POWER/SOFT 2. Press or to set correct time. Each press will increase or decrease 1 min. If the button is kept depressed, time will change quickly. 3. After time setting is confirmed, press SET, "AM" or "PM" stop flashing, while clock starts working. Remote controller's operati
ページ9に含まれる内容の要旨
Operation HEALTH operation Remote controller 1.Unit start Press ON/OFF on the remote controller, unit starts. 2.Health anion function Press HEALTH button. For each press, is displayed. Air conditioner starts health anion function operation. For twice press, disappears,the operation stops. When indoor fan motor is running, it has healthy process function. (It's available under any mode) FRESH When the fan in the indoor unit does not work, the health lamp lights up, but the anion gen
ページ10に含まれる内容の要旨
Operation Auto Operation 1. Unit start Remote controller Press ON/OFF on the remote controller, unit starts. 2.Select operation mode Press MODE button. For each press, operation mode changes as follows: Remote controller: AUTO COOL DRY FAN HEAT Then Select Auto operation 3.Select temp.setting Press TEMP. button Every time the button is pressed, temp.setting FRESH increase 1 C,if kept depressed, it will increase rapidly POWER/SOFT Every time the button is pressed, temp.setting decrease 1 C,if ke
ページ11に含まれる内容の要旨
Operation Cool Operation 1. Unit start Remote controller Press ON/OFF on the remote controller, unit starts. 2.Select operation mode Press MODE button. For each press, operation mode changes as follows: Remote controller: AUTO COOL DRY FAN HEAT Then Select COOL operation 3.Select temp.setting Press TEMP. button FRESH Every time the button is pressed, temp.setting increase 1oC,if kept depressed, it will increase POWER/SOFT rapidly Every time the button is pressed, temp.setting decrease 1oC,if ke
ページ12に含まれる内容の要旨
Operation Dry Operation Remote controller 1. Unit start Press ON/OFF on the remote controller, unit starts. 2.Select operation mode Press MODE button. For each press, operation mode changes as follows: Remote controller: AUTO COOL DRY FAN HEAT Then Select DRY operation 3.Select temp.setting Press TEMP. button FRESH Every time the button is pressed, temp.setting increase 1oC,if kept depressed, it will increase POWER/SOFT rapidly Every time the button is pressed, temp.setting decrease 1oC,if kept
ページ13に含まれる内容の要旨
Operation Fan Operation 1. Unit start Remote controller Press ON/OFF on the remote controller, unit starts. 2.Select operation mode Press MODE button. For each press, operation mode changes as follows: Remote controller: AUTO COOL DRY FAN HEAT Then Select FAN operation 3.Fan speed selection Press FAN button. For each press, fan speed changes as follows: FRESH Remote controller: LOW POWER/SOFT MED HI 4.Unit stop Press ON/OFF button, the unit stops. About FAN operation In FAN operation mode, the
ページ14に含まれる内容の要旨
Operation Heat Operation 1. Unit start Remote controller Press ON/OFF on the remote controller, unit starts. 2.Select operation mode Press MODE button. For each press, operation mode changes as follows: Remote controller: AUTO COOL DRY FAN HEAT Then Select HEAT operation 3.Select temp.setting Press TEMP. button Every time the button is pressed, temp.setting FRESH increase 1oC,if kept depressed, it will increase rapidly POWER/SOFT Every time the button is pressed, temp.setting decrease 1oC,if ke
ページ15に含まれる内容の要旨
Operation Air Flow Direction Adjustment 1.Status display of air sending Vertical flap Horizontal louvers Pos.1 Pos.1 Pos.2 Pos.2 Pos.3 Pos.3 FRESH Pos.4 Pos.4 POWER/SOFT Pos.5 Pos.5 Pos.6 Pos.6 (Auto swing) Pos.7 Pos.8 2.Up and down air flow direction For each press of button, air flow direction on remote controller displays as follows according to different operation modes: COOL/DRY/FAN remote controller: Pos.1 Pos.2 Pos.3 Pos.4 Pos.6 : HEAT: remote controller: Pos.5 Pos.4 Pos.3 Pos.2 P
ページ16に含まれる内容の要旨
Operation Sleep Operation Before going to bed, you can simply press the SLEEP button and unit will operate in SLEEP mode and bring you a sound sleep. SLEEP operation starts SLEEP operation stops Use of SLEEP function Approx.6hrs After the unit starts, set the operation status, then press SLEEP button before which the Rises 1OC 1 hr clock must be adjusted and time being set. Operation Mode Rises 1OC 1 hr 1. In COOL,DRY mode 1 hours after SLEEP mode starts, temp. will Unit stop Temp.setting be
ページ17に含まれる内容の要旨
Operation Timer On/Off Operation Set clock correctly before starting TIMER operation. 1. After unit starts, select your desired operation mode Remote Controller Operation mode will be displayed on LCD. 2. Timer mode selection Press TIMER button to change TIMER mode. Every time the button is pressed, display changes as follows: Remote controller: BLANK TIMER ON TIMER OFF TIMER ON-OFF Then select your desired TIMER mode (TIMER ON or TIMER OFF). " "or " "will flash. 3.T
ページ18に含まれる内容の要旨
Operation Timer On-Off Operation Set clock correctly before starting TIMER operation. Remote Controller 1. After unit starts, select your desired operation mode Operation mode will be displayed on LCD. 2. Timer mode selection Press TIMER button to change TIMER mode. Every time the button is pressed, display changes as follows: Remote controller: BLANK TIMER ON TIMER OFF TIMER ON-OFF Then select your desired TIMER mode (TIMER ON - OFF). " "will flash. 3.Time setting Press H
ページ19に含まれる内容の要旨
Operation POWER/SOFT Operation POWER Operation When you need rapid heating or cooling, you can use this function. Selecting of POWER operation Press POWER/SOFT button. Every time the button is pressed,display changes as follows: BLANK POWER SOFT Stop the display at In POWER operation status: In HEAT or COOL mode, fan speed automatically runs in HI mode for 15 min then returns to original status setting. To cancel POWER operation Press POWER/SOFT button twice ,POWER/SOFT disappears. FRESH SOFT Op
ページ20に含まれる内容の要旨
Operation Health airflow Operation 1.Press ON/OFF to starting Remote controller The liquid crystal will display the working state of last time (Except timer, sleeping, power/soft and health airflow). Setting the comfort work conditions. 2.The setting of health airflow function 1).Press the button of health airflow, appears on the display. The nether inlet and outlet grills of the air condit- ioner are closed and the airflow is blown horizontally from the above inlet and outlet grills. Avo
