ページ1に含まれる内容の要旨
®
MaxxBass
ページ2に含まれる内容の要旨
TABLE OF CONTENTS Congratulations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Caution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 ® Why Use MaxxBass . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 ® Why is MaxxBass Better . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 ® What is MaxxB
ページ3に含まれる内容の要旨
CONGRATULATIONS Thank you for choosing Orion audio equipment. At Orion we proudly design, engineer and manufacture audio products for aftermarket car audio. Our award winning engineering team utilizes innovative technology to consistently deliver Absolutely State of the Art performance, sound quality, reliability, and value. This Orion product reflects our commitment to offer you unparalleled versatility and quality for years of dependable service and listening enjoyment. SERVICE Do not attempt
ページ4に含まれる内容の要旨
recommended in two configurations. (Please see Wiring Configurations for more details.) 1) Front Stereo Configuration ® One MaxxBass Processor is used between the front channel source and front speaker amplifier to increase the bass response on only the front speakers. This is recommended to improve bass imaging in high performance systems with rear mounted subwoofers. 2) Dual Stereo Configurations For systems without rear subwoofers, the user may prefer to use two ® MaxxBass Processors, one for
ページ5に含まれる内容の要旨
This is accomplished using the science of psychoacoustics on how we perceive sound. By building audio systems optimized for how we hear sound, significant performance improvements can be obtained. This is analogous to designing and building televisions that only display red, green and blue dots. When we view these displays our visual perception combines these dots to make a full color spectrum without needing to reproduce all the necessary color frequencies. ® Unlike other bass technologies Maxx
ページ6に含まれる内容の要旨
® MAXXBASS SIGNAL FLOW Cross- Input HPF HPF Output Over + 60/80 Hz LPF LPF + Input Signal Example Harmonics ® HPF MAXXBASS 60/80 Hz Harmonics Processed Signal Example FEATURES ® Selectable MaxxBass Frequency Setting of 60Hz and 80Hz Green LED clip/Red LED power indicator signal Gold 2 Channel in/2 channel buffered full-range out RCA connectors 4-pin locking power plug ® Input connector for outboard MaxxBass Intensity controller Remote and on-box intensity controls Intensity adjustmen
ページ7に含まれる内容の要旨
SPECIFICATIONS Frequency 20hz-20kHz Signal-to-Noise Ratio >85dB Separation 65dB @ 1kHz Crossover Slope 24dB/octave Input Impedance 20,000 Ohms Input Sensitivity variable, 300mV to 3V peak to peak Output Level variable, 300mV to 5V peak to peak Supply Voltage 9 to 16 VDC INSTALLATION/MOUNTING NOTE: As an option, before beginning, disconnect the negative (-) terminal of the battery to prevent an electrical short to ground. Reconnect the negative terminal only after all connections have been made.
ページ8に含まれる内容の要旨
® MAXXBASS OUTLINE AND DIMENSIONS 5.90 in (15 cm) 5.51 in (14 cm) INTENSITY OUTPUT INPUT POWER CLIP MINMAX MINMAX MINMAX 4.53 in 2.48 in (11.5 cm) (6.3 cm) 80Hz ON 60Hz OFF FREQUENCY CROSS OVER GND REM +12V REM OUT 1.18 in (3 cm) INPUT OUTPUT POWER REMOTE 7
ページ9に含まれる内容の要旨
WIRING CONFIGURATIONS ® The MaxxBass Processor is recommended in two different configurations. 1. Front Stereo Configuration The figure below illustrates the wiring for a front stereo configuration. One ® MaxxBass Processor is used between the front channel source and front speaker amplifier to increase the bass response only on the front speakers. ® Implementing MaxxBass on the front speakers will increase the perceived bass response of these speakers down to 30-40Hz providing a Virtual Subwoof
ページ10に含まれる内容の要旨
2. Dual Stereo Configurations For systems without rear subwoofers, the user may prefer to use two ® MaxxBass Processors, one for the front speakers and one for the rear speakers. The units should be wired between the in-dash CD Receiver and the power amplifiers as shown below. Front speakers In-dash with Virtual CD Receiver LF RF TM Subwoofer Front Rear Rear speakers Maxx Maxx with Virtual ® ® RF RR Bass Bass TM Subwoofer Power Amplifiers NOTE: As an option, before beginning, disconnect the nega
ページ11に含まれる内容の要旨
The ground wire should be of the same gauge wire as the power wire. As a rule of thumb, use as short length of wire as possible. Find a location near the ® MaxxBass Processor that is metal ( the floor is ideal) and clean an area about the size of a quarter to bare metal. Drill a pilot hole in the middle of this area. Terminate the wire with a ring connector and attach it to the bare metal using a #8 sheet metal screw and washer (not supplied). We suggest crimping and/or soldering this connection
ページ12に含まれる内容の要旨
INPUT To use Speaker Level Inputs (common ground head units only), connect RCA plugs to the front or rear speaker leads as shown. NOTE: It is important to connect an input signal to both RCA input jacks if a stereo amplifier is used, otherwise the connected channel receives full range and the disconnected channel will receive only the harmonics. Use a RCA female to dual male “Y” cord if mono input is used. Front speakers In-dash with Virtual LF RF TM CD Receiver Subwoofer Front Rear Maxx LR RR ®
ページ13に含まれる内容の要旨
® MAXXBASS PROCESSOR SETTINGS To achieve proper performance it is important to set or tune the settings on ® the MaxxBass Processor to the final system. This section recommends initial settings and the users can then further adjust these for optimal listening. 1. CROSSOVER: The CROSSOVER control implements a -24dB/octave low pass filter on the input. Set the CROSSOVER control to OFF if the amplifier ® and speakers after the MaxxBass Processor are full range speakers or if passive crossovers are
ページ14に含まれる内容の要旨
TROUBLESHOOTING NO SOUND Is the POWER LED lit? YES NO Check Input cables for signal by Check power and remote Connecting them straight to the turn-on wire for voltage. Subwoofer amplifier. Make sure the ground wire is Secure. ANY SOUND NOW? YES NO Problem is in the Crossover. Problem is elsewhere in the See your local Authorized system. Check head Unit and Orion Dealer. amplifiers. SOUND IN ONE CHANNEL ONLY Reverse left and right RCA outputs for one band (i.e.-subwoofers) SOUND IS NOW IN OP
ページ15に含まれる内容の要旨
OPPOSITE CHANNEL SAME CHANNEL Reverse RCAs to head unit Problem is in the Crossover. (Check Balance Control) See your local Authorized Orion dealer. SOUND IS NOW IN OPPOSITE CHANNEL SAME CHANNEL Problem is in the head unit. Problem is in the RCA cables. LOW OUTPUT FROM ONE BAND Check crossover frequencies and check gain control on the effected amplifier(s). STILL LOW OUTPUT - See your local Authorized Orion dealer. 14
ページ16に含まれる内容の要旨
15
ページ17に含まれる内容の要旨
Warranty LIMITED TWO YEAR CONSUMER WARRANTY: Directed Electronics, Inc. promises to the original purchaser, to replace this product should it prove to be defective in workmanship or material under normal use, for a period of two years from the date of purchase by the dealer as indicated by the date code marking of the product PROVIDED the product was installed by an authorized Directed dealer. During this two year period, there will be no charge for this replacement PROVIDED the unit is returned
