ページ1に含まれる内容の要旨
HEAT CONTROLLER, INC.
Wall Mounted
Mini - Split System
DMC24DB-1, DMH24DB-1
DMC36TB-1, DMH36TB-1
Dual-Zone, Tri-Zone
Air Conditioning / Heat Pump
Important Information
• Please read carefully and thoroughly this manual before operating this unit.
• Contact a qualified sevice technician for installation, repair and maintenance of this unit.
• The appliance is not intended for use by young children or those who require supervision.
• Young children should be supervised to ensure that they do not p
ページ2に含まれる内容の要旨
Room Air Conditioner Owner’s Manual TABLE OF CONTENTS FOR YOUR RECORDS Write the model and serial numbers here: Safety Precautions.................3 Model # Prior to Operation ..................8 Serial # You can find them on a label on the side of each unit. Operating Instructions...........9 Dealer's Name Remote Controller ..............9 Date Purchased Remote Control Staple your receipt to this page in the event you need it Operation...........................11 to prove date of purchase o
ページ3に含まれる内容の要旨
Safety Precautions Safety Precautions To prevent the injury of the user or other people and property damage, the following instructions must be followed. Incorrect operation due to ignoring instruction will cause harm or damage. The seriousness is classified by the following indications. This symbol indicates the possibility of death or serious injury. This symbol indicates the possibility of injury or damage to properties only. The meanings of the symbols used in this manual are as shown
ページ4に含まれる内容の要旨
Safety Precautions Be sure the installation area Install the indoor unit on the Do not handle the pipe by does not deteriorate with age. wall where the height from yourself(Costomer) the floors more than 8ft(2.4m) • If the base collapses, the air • There are sharp moving parts that • High-Pressure refrigent may cause conditioner could fall with it, could cause personal injury. personal injury. causing property damage, product failure, and personal injury. 8ft(2.4m) Operation Do not allow wa
ページ5に含まれる内容の要旨
Safety Precautions Stop operation and close any Do not open the inlet grill of When the product is soaked window in storm or hurricane the product during operation. (flooded or submerged), before the hurricane arrives. (Do not touch the contact an Authorized electrostatic filter, if the unit Service Center. is so equipped.) • There is risk of property damage, • There is risk of physical injury, • There is risk of electrical shock. failure of product, or electric electric shock, or product. sho
ページ6に含まれる内容の要旨
Safety Precautions Installation Always check for Install the drain hose to Keep level even when gas(refrigerant) leakage after ensure that water is drained installing the product. installation or repair of away properly. product. • Low refrigerant levels may cause • A bad connection may cause • To avoid vibration or water product failure. water leakage. leakage. 90° Do not install the product Use two or more people to lift Do not install the product where the noise or hot air and transport
ページ7に含まれる内容の要旨
Safety Precautions Use a soft cloth to clean. Do not touch the metal parts Do not step on or put Do not use harsh detergents, of the product when anything on the product. solvents, etc. removing the air filter. They (outdoor unit) are very sharp! • There is risk of fire, electric shock • There is risk of personal injury. • There is risk of personal injury and or damage to the plastic parts of failure of product. the product. Always insert the filter Do not drink the water Use a firm stool or l
ページ8に含まれる内容の要旨
Prior to operation Prior to operation Preparing for operation 1. Contact an installation specialist for installation. 2. Connect the power cable between indoor unit and outdoor unit properly. 3. Use a dedicated circuit. Usage 1. Being exposed to direct airflow for an extended period of time could be hazardous to your health. Do not expose occupants, pets, or plants to direct airflow for extended periods of time. 2. Do not use this air conditioner for non-specified special purposes (e.g. preservi
ページ9に含まれる内容の要旨
Operating Instructions Operating Instructions Remote Controller 1. Remove the battery cover by pulling it according to the arrow direction. 2. Insert new batteries making sure that the (+) and (-) of battery are installed correctly. 3. Reattach the cover by sliding it back into position. NOTICE Use 2 AAA(1.5volt) batteries. Do not use rechargeable batteries. Storage and Tips For Using the Remote Controller • The remote control may be stored mounted on a wall. • To operate the room air conditione
ページ10に含まれる内容の要旨
Operating Instructions Signal Receptor Receives the signals from the remote controller.(Signal receiving sound: two short beeps or one long beep.) Operation indicating lamps Operation Indication Lamps On/Off : Lights up during the system operation. Sleep Mode : Lights up during Sleep Mode Auto operation. Timer : Lights up during Timer operation. Defrost Mode : Lights up during Defrost Mode or Hot Start operation (Heat pump model only) OUT Outdoor unit : Lights up during outdoor unit operation
ページ11に含まれる内容の要旨
Operating Instructions Remote Control Operation Controls 1. START/STOP BUTTON Operation starts when this button is pressed Signal transmitter and stops when the button is pressed again. 2. OPERATION MODE SELECTION BUTTON (Cooling Only) (Heat Pump) Used to select the operation mode. 3. ROOM TEMPERATURE SETTING BUTTONS Used to select the room temperature. 4. INDOOR FAN SPEED SELECTOR Used to select fan speed in four steps 5 1 low, medium, high and CHAOS. 6 5. JET COOL 3 Used to start or stop the
ページ12に含まれる内容の要旨
Operating Instructions Cooling Operation Press the Start/Stop button. The unit will respond with beep sound. 1 Open the door on the Remote Controller. To select Cooling Operation, press the Operation Mode Selection button. 2 Each time the button is pressed, the operation mode is shifted in the direction of the arrow. Cooling Auto Healthy Heating Dehumidification (Heat pump model only) (Cooling Only (Heat Pump model) model) Set the temperature lower than the room temperature. The temperature c
ページ13に含まれる内容の要旨
Operating Instructions Auto Operation Press the Start/Stop button. The unit will respond with beep 1 sound. Open the door on the Remote Controller. To select Auto Operation, press the Operation Mode Selection button. 2 Each time the button is pressed, the operation mode is shifted in the direction of the arrow. Cooling Auto Healthy Heating Dehumidification (Heat pump model only) (Cooling Only (Heat Pump model) model) The temperature and fan speed are automatically set by the ON electronic cont
ページ14に含まれる内容の要旨
Operating Instructions Healthy Dehumidification Operation Press the Start/Stop button. The unit will respond with beep 1 sound. Open the door on the Remote Controller. To select Healthy Dehumidification Operation, press the Operation Mode 2 Selection button. Each time the button is pressed, the operation mode is shifted in the direction of the arrow. Cooling Auto Healthy Heating Dehumidification (Heat pump model only) (Cooling Only (Heat Pump model) model) Set the fan speed. You can select the
ページ15に含まれる内容の要旨
Operating Instructions Heating Operation(Heat pump model only) Press the Start/Stop button. The unit will respond with 1 beep sound. Open the door on the Remote Controller. To select Heating Operation, press the Operation Mode Selection button. 2 Each time the button is pressed, the operation mode is shifted in the direction of the arrow. Cooling Auto Healthy Heating Dehumidification (Heat pump model only) Set the temperature higher than the room temperature. The temperature can be set within
ページ16に含まれる内容の要旨
Operating Instructions Jet Cool Press the Start/Stop button. 1 The unit will respond with beep sound. Press the Jet Cool button to operate the 2 speed cooling/heating mode and the unit will operate in super high fan speed on cooling/heating mode for 30/60 minutes. To cancel the Jet Cool mode, press the Jet Cool button or the fan button or the room temperature setting button again 3 and the unit will operate in high fan speed in cooling/heating mode or or NOTICE ❏ Jet Cool function in heating mo
ページ17に含まれる内容の要旨
Operating Instructions 2nd F Operation Press the Start/Stop button. The unit will respond with 1 beep sound. nd Open the door of the Remote Controller and press the 2 F button to operate functions printed in blue at bottom of 2 buttons. nd (Check the indication of 2 function on Remote Controller display.) These buttons operate the timer setting as follows: CANCEL ON OFF SET AUTO CLEAN CANCEL ON OFF SET AUTO CLEAN nd 2 function goes off in a short time automatically or when the button is pressed
ページ18に含まれる内容の要旨
Additional features Additional features Sleep Mode 1. Press the Sleep Mode Auto button to set the time To cancel the Sleep Mode, press the sleep you want the unit to turn off automatically. Mode Auto button several times until the star ( ) disappears from the operation display. 2. The Timer is programmed in one-hour increments by pressing the Sleep Mode Auto button 1 to 7 NOTICE The Sleep Mode will be operated at times. low fan speed (cooling) or medium fan speed The sleep mode is available
ページ19に含まれる内容の要旨
Additional features Vertical Airflow Direction Control The up/down airflow (Vertical Airflow) can be adjusted NOTICE by using the remote control. ❏ If you press the CHAOS swing button, the horizontal airflow direction is changed automatically based on the CHAOS algorithm to distribute the air in the room evenly and at the same time to make the human body feel most comfortable, as if enjoying a natural breeze. ❏ Always use the remote control to adjust the up/down airflow direction. Manually movin
ページ20に含まれる内容の要旨
Additional features Auto clean 1. Whenever you press the AUTO CLEAN button, Auto Clean Function will be selected or cancelled. AUTO CLEAN 2. Auto Clean function works before and after cooling or dehumidification mode. For details, refer to the below points. 3. When the unit is started after selecting Auto Clean ,the Cool Start function operates and indoor Fan is started after 20 seconds. 4. When you press Start/Stop button to turn off the unit after the you have selected Auto Clean function, the
