ページ1に含まれる内容の要旨
45603
Wireless Lighting Control
Fluorescent &
Appliance Module
™
GE SmartHome
®
Z-Wave Certified
Wireless Lighting Control
ページ2に含まれる内容の要旨
Introduction: ® Thank you for your purchase of a GE Z-Wave control device. Z-Wave technology is designed to automate lighting/home control and provide easy remote operation of all your Z-wave enabled devices. The GE Z-Wave product family includes a variety of devices to control lighting in your home. It is up to you whether you want to control one room or your entire house and whether you want to do it all now or start with one room and add more over time. This module is one compo
ページ3に含まれる内容の要旨
The device plugged into the Z-Wave controlled outlet on this module must not exceed 600 watts (Incandescent); 1800W (15A) Resistive or ½ HP Motor. Total load capacity for both outlets is 1800W (15A) Resistive. There are no user serviceable parts in this unit. Manual/Program button Standard AC outlet Z-wave outlet (other end) To reduce the risk of electric shock, this product has a grounding type plug that has a third (grounding) pin. This plug will only fit into a grounding type po
ページ4に含まれる内容の要旨
WARNING RISK OF FIRE RISK OF ELECTRICAL SHOCK RISK OF BURNS The Load-Sense feature on this Z-Wave product will turn the power to the connected device ON when a change in the load is detected. Z-Wave connected devices should always be unplugged before performing any service or maintenance of the devices. Controlling Appliances: Exercise extreme caution when using Z-Wave devices to control appliances. Operation of the Z-Wave device may be in a different room than the controlled appliance, a
ページ5に含まれる内容の要旨
Wireless Range This device complies with the Z-Wave standard of open- air, line of sight transmission distances of 65 feet. Actual performance in a home depends on the number of walls between the remote controller and the destination device, the type of construction and the number of Z-Wave enabled devices installed in the control network. GE Z-Wave Network Every Z-Wave enabled device acts as a signal repeater and multiple devices result in more possible transmission routes which helps
ページ6に含まれる内容の要旨
Effects of Home Construction on Wireless Range Between Z-Wave Enabled Devices. Note: The distances shown in the table below are typical examples. Actual performance in your home will vary. From the Remote (or repeating Z-Wave module) to destination device: Type of Construction Wood Frame Brick, Tile or w/Drywall Concrete Plastic Metal Plastic Metal J-Boxes* J-Boxes J-Boxes* J-Boxes ** 0 100’ 80’ 100’ 80’ Number 1 70’ 56’ 60’ 48’ of Walls or Obstacles 2 49’ 39’ 36’ 29’ 3 34’ 27’ 21’ 17’ *
ページ7に含まれる内容の要旨
Please Note: Z-Wave home control networks are designed to work properly alongside 802.11 wireless computer networks, Bluetooth and other 2.4GHz or 5.8GHz devices. Some baby cams, wireless video devices and older cordless phones using the 900MHz frequency range may cause interference and limit Z-Wave functionality. Many 900MHz products have a switch to select channel “A” or “B”. You may find that one of these channels will cause less interference than the other. Key Features 1. One Z-w
ページ8に含まれる内容の要旨
Basic Operation The connected light can be turned ON in three ways: 1. With a Z-Wave remote 2. Manually with the push button on the Z-Wave module 3. By the Load-Sensing feature. Normally, the Z-Wave module controls the ON/Off state of the connected light and power is either turned On or Off at the module (either manually or by the remote). If the switch on the connected light is used, the Z-Wave control circuitry automatically senses that the light is being turned On and activates the Z-w
ページ9に含まれる内容の要旨
control network with your primary controller. - Refer to the instructions for your primary controller to access the network setup function and include or exclude devices. - When prompted by your primary controller, tap the button. - The primary controller should indicate that the action was successful. If the controller indicates the action was unsuccessful, please repeat the procedure. -Once the module is part of the network, the same basic procedure is used to add the module to groups
ページ10に含まれる内容の要旨
Load Sensing Load sensing is disabled when shipped from the factory. This feature can be enabled if desired. Setting parameter 29 to a value of 1 will enable the Load Sense function. - Parameter No: 29 - Length: 1 Byte - Valid Values = 0 or 1 (default 0) Note: When replacing a burned-out light bulb, the load sensing feature (if enabled) will automatically turn the light ON when the new bulb is installed even if the Z-wave module was turned OFF. Restoring Factory Defaults All Configurat
ページ11に含まれる内容の要旨
devices using the lighting control classification. The 45601 deluxe remote with LCD readout can control other Z-Wave certified devices like thermostats as well as lighting. WARRANTY JASCO Products warrants this product to be free from manufacturing defects for a period of two years from the original date of consumer purchase. This warranty is limited to the repair or replacement of this product only and does not extend to consequential or incidental damage to other products that may be
ページ12に含まれる内容の要旨
FCC U2Z45602-3 The Federal Communication Commission Radio Frequency Interference Statement includes the following paragraph: The equipment has been tested and found to comply with the limits for a Class B Digital Device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment uses, generates and can radiate radio frequency energy and, if not installed and used in accordance
ページ13に含まれる内容の要旨
Important Note: To comply with the FCC RF exposure compliance requirements, no change to the antenna or the device is permitted. Any change to the antenna or the device could result in the device exceeding the RF exposure requirements and void user’s authority to operate the device. Compliance with IC Rules and Regulations IC: 6924A-45602A3 Jasco Products Company Model: 45603 This Class B digital device complies with Canadian ICES-003. SPECIFICATIONS Power 120VAC, 60Hz Signal (Frequency) 908
ページ14に含まれる内容の要旨
ページ15に含まれる内容の要旨
ページ16に含まれる内容の要旨
is a registered trademark of General Electric Company and is used under license to J asco Products Company LLC, 10 E Memorial Rd., Oklahoma ™ GE SmartHome City, Oklahoma 73114 Made in China Hecho en China All brand names shown are trademarks of their respective owners. Todas las marcas que aparecen aquí son marcas registradas de sus respectivos dueños.
