ページ1に含まれる内容の要旨
OPERATOR’S MANUAL
18 VOLT CORDLESS WORKLIGHT
P700
BATTERIES
AND CHARGERS
SOLD SEPARATELY
Your cordless worklight has been engineered and manufactured to Ryobi’s high standards for dependability, ease of
operation, and operator safety. When properly cared for, it will give you years of rugged, trouble-free performance.
WARNING: To reduce the risk of injury, the user must read and understand the operator’s manual before using
this product.
Thank you for buying a Ryobi product.
SAVE THIS MANU
ページ2に含まれる内容の要旨
TABLE OF CONTENTS n Introduction......................................................................................................................................................................2 n General Safety Rules .......................................................................................................................................................3 n Specific Safety Rules.....................................................................................................
ページ3に含まれる内容の要旨
GENERAL SAFETY RULES n Use battery only with charger listed. WARNING! MODEL BATTERY PACK (P100) CHARGER (P110) READ AND UNDERSTAND ALL INSTRUCTIONS. Fail- P700 130255004 1423701, 140237023 ure to follow all instructions listed below, may result in or 130224028 or 140237021 electric shock, fire and/or serious personal injury. WORKLIGHT USE AND CARE n When battery pack is not in use, keep it away from SAVE THESE INSTRUCTIONS other metal objects like: paper clips, coins, keys, nails, WORK A
ページ4に含まれる内容の要旨
SPECIFIC SAFETY RULES n Do not permit children to use worklight unsupervised. n If wrapped or in contact with fabrics, the worklight It is not a toy. The temperature of the bulb will become lens can produce sufficient heat to melt some fabrics. hot after being on for only a short period of time. This To avoid serious personal injury, never allow the worklight hot temperature can cause burn injury if touched and can lens to come in contact with anything. create sufficient heat to melt some f
ページ5に含まれる内容の要旨
SYMBOLS Some of the following symbols may be used on this worklight. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the worklight better and safer. SYMBOL NAME DESIGNATION/EXPLANATION V Volts Voltage A Amperes Current Hz Hertz Frequency (cycles per second) W Watt Power min Minutes Time Alternating Current Type of current Direct Current Type or a characteristic of current n No Load Speed Rotational speed, at no load o Class II Construc
ページ6に含まれる内容の要旨
SYMBOLS The following signal words and meanings are intended to explain the levels of risk associated with this product. SYMBOL SIGNAL MEANING DANGER: Indicates an imminently hazardous situation, which, if not avoided, will result in death or serious injury. WARNING: Indicates a potentially hazardous situation, which, if not avoided, could result in death or serious injury. CAUTION: Indicates a potentially hazardous situation, which, if not avoided, may result in minor or moderate injury.
ページ7に含まれる内容の要旨
FEATURES PRODUCT SPECIFICATIONS Battery.....................................................................................................................................................................18 Volt DC Charger Input ........................................................................................................................................ 120 V, 60 Hz, AC only Charge Rate ....................................................................................................
ページ8に含まれる内容の要旨
ASSEMBLY UNPACKING WARNING: This product has been shipped completely assembled. If any parts are missing do not operate this worklight until n Carefully remove the worklight and any accessories from the missing parts are replaced. Failure to do so could the box. Make sure that all items listed in the packing list result in possible serious personal injury. are included. n Inspect the worklight carefully to make sure no breakage or damage occurred during shipping. WARNING: n Do not discard t
ページ9に含まれる内容の要旨
OPERATION NOTE: Batteries will not reach full charge the first time they WARNING: are charged. Allow several cycles (operation followed by recharging) for them to become fully charged. Do not allow familiarity with worklights to make you care- less. Remember that a careless fraction of a second is CHARGING A COOL BATTERY PACK sufficient to inflict serious injury. If battery pack is within normal temperature range, the red LED on charger will come on. WARNING: NOTE: If the charger does not
ページ10に含まれる内容の要旨
OPERATION n After normal usage, a minimum of 1 hour of charging time TO INSTALL BATTERY PACK is required to fully recharge battery pack. See Figure 4. n The battery pack will become slightly warm to the �n Begin with a fully charged battery pack. touch while charging. This is normal and does not n Orient battery pack so that raised rib on battery pack indicate a problem. aligns with groove inside worklight. Battery pack is de- n Do not place the charger and battery pack in an area of signed
ページ11に含まれる内容の要旨
OPERATION TO REMOVE BATTERY PACK 180° ROTATING HEAD See Figure 4. �n To remove battery pack, locate latches on end of bat- tery pack and depress to release battery pack from the worklight. CAUTION: Battery tools are always in operating condition. Use SWITCH caution when carrying to prevent depressing the switch trigger when light is not needed. SWITCH See Figure 5. To turn the worklight ON and OFF, depress the switch. 180º ROTATING HEAD See Figure 5. Rotate the head of worklight to change t
ページ12に含まれる内容の要旨
MAINTENANCE BULB REPLACEMENT WARNING: See Figure 6. When servicing, use only identical Ryobi replacement When purchasing replacement bulb, request recommended parts. Use of any other parts may create a hazard or part number 7817502. cause product damage. TO REPLACE BULB: n Allow bulb to cool. �n Remove battery pack by depressing side latches to re- WARNING: lease from worklight. Always wear safety goggles or safety glasses with side �n Remove lens cover by turning in a counterclockwise shie
ページ13に含まれる内容の要旨
MAINTENANCE BATTERIES BATTERY PACK REMOVAL AND PREPARATION FOR RECYCLING The battery pack for this worklight is equipped with nickel- cadmium rechargeable batteries. Length of service from To preserve natural resources, please each charging will depend on the type of work you are recycle or dispose of batteries doing. properly. This product contains nickel-cadmium The batteries in this worklight have been designed to pro- batteries. Local, state or federal laws vide maximum trouble-free li
ページ14に含まれる内容の要旨
OPERATOR’S MANUAL 18 VOLT CORDLESS WORKLIGHT P700 • SERVICE Now that you have purchased your worklight, should a need ever exist for repair parts or service, simply contact your nearest Ryobi Authorized Service Center. Be sure to provide all pertinent facts when you call or visit. Please call 1-800-525-2579 for your nearest Ryobi Authorized Service Center. You can also check our web site at www.ryobitools.com for a complete list of Authorized Service Centers. • MODEL NO. AND SERIAL NO. The
