ページ1に含まれる内容の要旨
HANDBOOK CD62
Arcam CD62 Compact Disc player
ページ2に含まれる内容の要旨
Safety guidelines 9. Power sources Safety instructions Only connect the appliance to a power supply of the type This product is designed and manufactured to meet strict described in the operating instructions or as marked on the quality and safety standards. However, you should be aware of appliance. the following installation and operation precautions: 10. Power-cord protection 1. Take heed of warnings and instructions Power supply cords should be routed so that they are not likely You sho
ページ3に含まれる内容の要旨
Using this handbook This handbook has been designed to give you all the information you need to install, connect, set up and use the Contents Arcam CD62 compact disc player. The CR224 remote control Safety guidelines 2 handset supplied with this equipment is also described, as it Safety instructions 2 applies to operating the CD62. Safety compliance 2 Note that this product is not upgradeable to a CD72, CD92, or Using this handbook 3 any other model in the Arcam range. Safety 3 Models covere
ページ4に含まれる内容の要旨
Installation Positioning the unit Connecting to a power supply Always place the CD player on a level, fi rm surface. Placing Wrong plug? your player on a set of dedicated sorbothane isolation feet Check that the plug supplied with the unit fi ts your supply and will isolate the unit from its surroundings as well as absorbing that your mains supply voltage agrees with the voltage setting the vibrations created within the player itself. You will generally (120V or 230V) indicated on the rear p
ページ5に含まれる内容の要旨
Using your CD player COMPACT DISC PLAYER CD62 24 BIT DAC TRACK LOAD PLAY STOP PAUSE POWER 24 3 5 6 7 1 POWER SKIP TRACK 1 7 Press this button to switch the CD player on and off. When fi rst To start a CD with a track other than the fi rst, press or powered up with no CD installed the display shows: to locate the desired track. To select another track during play, press or . The track is played automatically after selection. Pressing once --NO DISC-- returns to the start of the current tra
ページ6に含まれる内容の要旨
Using the CR224 remote control PROG (Program) 0–9 keypad You can program a selection of up to 24 tracks from a disc This allows direct access to individual tracks on the disc. to play in any order. Select a track by using the and To select a track, press the corresponding keypad button. buttons, then press PROG to program the track into memory For tracks greater than 9, enter the digits in sequence. For (‘PROGRAM’ appears on the display to indicate that you have example, to play track 15, p
ページ7に含まれる内容の要旨
Technical specifi cation Digital to Analogue conversion Physical 24-bit multilevel Delta-Sigma DAC Dimensions W430 x D290 x H84mm Weight 4.6kg nett/6.1kg packe Laser pick-up 3 beam Power consumption 32VA maximum Laser wavelength 780nm Numerical aperture 0.45 Digital output connection 75Ω co-axial Dynamic range 106dB optical TOSLINK Signal to noise ratio (CCIR) >100dB Supplied accessories Harmonic distortion (0dB, 1kHz) <0.005% Frequency response (±0.5dB) 5Hz–20kHz Mains lead Output level (0
ページ8に含まれる内容の要旨
Guarantee Worldwide Guarantee It should be sent carriage prepaid by a reputable carrier -– This entitles you to have the unit repaired free of charge, during NOT by post. No responsibility can be accepted for the unit the fi rst two years after purchase, at any authorised Arcam whilst in transit to the dealer or distributor and customers are distributor provided that it was originally purchased from therefore advised to insure the unit against loss or damage an authorised Arcam dealer or dist
