ページ1に含まれる内容の要旨
CS-8050
HANDS-FREE KEYLESS ENTRY / IMMOBILIZER SYSTEM
INSTALLATION & OPERATING INSTRUCTIONS
INTRODUCTION
CONGRATULATIONS on your choice of a Hands-Free Keyless Entry & Immobilizer System by Crimestopper
Security Products Inc. This booklet contains the information necessary for installing, using, and maintaining
your alarm system. If any questions arise, contact your installation dealer or Crimestopper Security Products
Inc. at the Tech Support number below.
*IMPORTA
ページ2に含まれる内容の要旨
INSTALLATION PRECAUTIONS & WARNINGS BEFORE BEGINNING, check all vehicle manufacturer cautions and warnings regarding electrical service (AIR BAGS, ABS BRAKES, AND BATTERY). DO NOT ROUTE ANY WIRING THAT MAY BECOME ENTANGLED with brake, and gas pedals, steering column, or any other moving parts in the vehicle. COMPONENT MOUNTING Control Unit: DO NOT mount or wiring harness where they can become entangled with moving parts such as brake/gas/clutch pedals, or the steering column! The
ページ3に含まれる内容の要旨
WIRING WIRE #5: +12Volt Power Input: Connect to Battery Positive Terminal. WIRE #6: Immobilizer Circuit #1 Output: This is part of the immobilizer circuit (on-board relay). Cut the Ignition wire and connect ONE end to this wire. WIRE #7: Immobilizer #1 Input: This is part of the immobilizer circuit (on-board relay). Connect the other end of the Ignition wire to this wire. WIRE #8: (-) Horn Honk Output (Optional, may require relay): Connects to (-) Negative Horn activation circ
ページ4に含まれる内容の要旨
POWER DOOR LOCK WIRING NEGATIVE TRIGGER DOORLOCK WIRING POSITIVE TRIGGER DOORLOCK WIRING GREEN GREEN FUSED RED RED +12V BLUE + BLUE 85 86 85 86 87 87 30 87A 30 87A FACTORY FACTORY L L POWER POWER LOCKING LOCKING UL UL RELAYS RELAYS REVERSE POLARITY DOOR LOCK WIRING ACTUATOR DOOR LOCK WIRING GREEN GREEN FUSED FUSED RED RED +12V +12V BLUE + BLUE + 85 86 85 86 85 86 85 86 87 87 87 87 87A 30 87A 30 87A 30 87A 30 MASTER SWITCH + CUT L UL CUT
ページ5に含まれる内容の要旨
OPERATING INSTRUCTIONS How the System Works: (Hands-Free Mode) As you turn your Ignition OFF and leave your vehicle, the system will automatically arm. The tiny hands-free remote transmitter on your key chain emits a low power signal every few seconds. As you return to your vehicle (approximately within 15-30 feet), the immobilizer system will “pick up” the signal from the tiny remote and disarm/unlock your vehicle. To operate in hands-free mode, the remote transmitter must be turned
ページ6に含まれる内容の要旨
ORERATING INSTRUCTIONS Turning the Remote OFF (Stop sending signals): Press and hold the remote button for 5 seconds until LED on remote flashes twice (Ignore first single flash). The remote is now OFF and will not send signals. When you are going to be away from your vehicle for extended periods of time, it is advisable to turn the remote off to save its battery life. However before you return to your car, you must re-activate the remote or press the button using it manually. Remot
ページ7に含まれる内容の要旨
HANDS-FREE TRANSMITTER PROGRAMMING This system can code learn up to 4 different transmitters. All transmitters must be learned at one time. rd 1. Turn ignition switch on and off 3 times leaving it on the 3 time. (on/off, on/off, on) LED will Flash 3 times. 2. Push the Valet/Programming button for 5 seconds until the in-dash LED flashes 5 times. 3. Press the Button on the hands-free transmitter once – The dash LED will flash once to confirm programming. Repeat this step within 5 seconds
ページ8に含まれる内容の要旨
CS-8050 SYSTEM DIAGRAM IMMOBILIZER CIRCUIT #1 #1 (On Board Relay) #2 #3 GROUND Some systems may not include * IGNITION a large connector here, however #4 +12V the wiring diagram is identical. #5 - + BATTERY * IMMOBILIZER #6 CS-8050 CIRCUIT #2 #7 (On Board Relay) BLUE PLUG: VALET (-) NEGATIVE MAY REQUIRE RELAY #8 RED PLUG: LED HORN OUTPUT WHITE PLUG: DOOR LOCKS (-) NEG. DOME #9 OR OEM (-) NEGATIVE DISARM #10 ARMED OUTPUT BLUE ANTENNA RED VALET/ PROGRAM WHITE SWITCH LED (-) LOCK OUTPUT
