ページ1に含まれる内容の要旨
Platinum Series Platinum Series
Platinum Series Platinum Series Platinum Series
2000 2000
2000 2000 2000
ADJUSTABLE BED
WITH WALLHUGGER® ACTION
MODEL NO
P-2000
• Introduction
• Installation
• Operation
• Trouble Shooting
• Warranty
RETAIN FOR FUTURE
REFERENCE
Manual Part Number:
99300487
SERIAL NO:
1-04
ページ2に含まれる内容の要旨
WARNINGS WARNING! IMPORTANT SAFETY INSTRUCTIONS PLEASE READ THESE INSTRUCTIONS THOROUGHLY BEFORE USING THIS PRODUCT. Your Adjustable Bed has been totally engineered to provide you with reliability of operation and the strength you deserve. The manufacturer has given each bed a thorough inspection and testing prior to shipment. The utmost in comfort and safety has been provided for you. This bed is for HOME use only. It is NOT designed for hospital use and was not designed to meet hospital sta
ページ3に含まれる内容の要旨
WARNINGS For best performance, consumers should enter and exit the adjustable bed with the bed in the flat or down position. A note to consumers with pacemakers: As with any product that produces a vibrating motion, it is possible that some pacemakers may interpret this motion as a false sense of movement and/or exercise. This may or may not affect your pacemaker. If you have any concerns, please consult your physician. WEIGHT RESTRICTIONS: The recommended weight restrictions on our adjustable
ページ4に含まれる内容の要旨
INSTALLATION STEP 1 Remove and discard the packing materials from the bottom of the base unit. You will see the mattress retainer bracket and headboard brackets attached to the side rail of the bed. Remove these items and set aside for the moment. Remove bagged parts and the power cord from the underside of the bed. MATTRESS RETAINER BRACKET HEADBOARD BRACKET STEP 2 Insert casters into the caster sockets at the bottom of each leg. If necessary, strike the center of the caster lightly with a
ページ5に含まれる内容の要旨
INSTALLATION FIGURE 1 STEP 3 Lift the base unit from the carton and, keeping the unit top-side-down, place it on a raised surface such as the mattress. Remove the four bolts at the foot end of the bed and attach the mattress retainer.. See Figure 1. The mattress retainer must be used or the mattress will slide off the end of the bed when the head is raised. If this product is not going to be attached to a headboard, omit Step 4 and Step 6. STEP 4 Attach the headboard brackets per
ページ6に含まれる内容の要旨
INSTALLATION HEADBOARD BRACKET ASSEMBLY INSTRUCTIONS Assemble headboard brackets for full or queen size bedding as shown in Detail A. Headboard brackets for twin size bedding do not require assembly. DETAIL A QUEEN SIZE FULL SIZE Slide headboard bracket assembly between the metal frame and the wood trim panel. Position brackets to allow a one inch space between the mattress and the headboard. Attach brackets to the frame as indicated in Detail B. DETAIL B 5
ページ7に含まれる内容の要旨
OPERATION P-2000 OPERATING INSTRUCTIONS Transmission Indicator Light: Position Buttons: (see note below) Verifies a button is being pressed. Automatically moves bed to the preset position from any other setting. To stop Massage Set Button: the bed while in motion, press and hold Once desired settings of the any button until the bed stops. massagers and wave have been activated, press this button to save Foot Up/Down Rocker Switch: those settings for the Favorite Adjusts foot section of the bed
ページ8に含まれる内容の要旨
TROUBLE SHOOTING ELECTRICAL If the bed does not operate: • Check the power cord to see that it is securely plugged into the electrical outlet. • Check the outlet by plugging in a lamp or another electrical device. • Replace batteries in the remote hand control. • Perform the Auto Learn Feature outlined on your Remote Operation page. • If bed still does not work, contact: Leggett & Platt Warranty Service Department P.O. Box 140 Linwood, NC 27299 1-800-888-3078 FOR BEST RESULTS, YOUR BED SHOULD
ページ9に含まれる内容の要旨
WARRANTY LEGGETT & PLATT 20-YEAR LIMITED WARRANTY Leggett & Platt, Incorporated (“L&P”) warrants this P-2000 Bed to the consumer who is the original purchaser (the “Purchaser”), subject t o the terms and conditions set forth herein. This warranty begins on the “warranty commencement date” which is the date of purchase for new, unused beds and the date of manufacture for beds that have been used as floor or display models. [Thus, on a floor model bed, the warranty is a portion of the limited
ページ10に含まれる内容の要旨
WARRANTY, Continued Repairs to or replacement of a P-2000 bed or its components under the terms of this Limited Warranty will apply to the original warranty period and will not serve to extend such period. The decision to repair or to replace defective parts under this warranty shall be made, or cause to be made, by L&P at its option and in its sole discretion. REPAIR OR REPLACEMENT SHALL BE THE SOLE REMEDY OF THE PURCHASER. THERE SHALL BE NO LIABILITY ON THE PART OF L&P FOR ANY SPECIAL, INDI
ページ11に含まれる内容の要旨
Platinum Series Platinum Series Platinum Series Platinum Series Platinum Series 2000 2000 2000 2000 2000 ADJUSTABLE BED WITH WALLHUGGER® ACTION MODEL NO: This model number will be found on the decal which is attached to the main frame rail under the headboard. Always mention the model number when requesting repair parts. P-2000 WHEN ORDERING PARTS OR REQUESTING SERVICE ASSISTANCE, PLEASE HAVE THE FOLLOWING INFORMATION READY: • THE PART DESCRIPTION • THE MODEL NUMBER - LAB 6 • THE NAME OF THE
