ページ1に含まれる内容の要旨
Gas Dryer
,., .......... ,...... _,;;;_ I..A°C_ 0
Secadora a Gas
Models/Modelos 110.9656:_,9657:_
= colornumber/nOmerode color
W10034920 Sears Roebuck and Co., Hoffman Estates, IL 60179 U.S.A. www.sears.com
ページ2に含まれる内容の要旨
TABLE OF CONTENTS KENMORE APPLIANCE AND OPTIONAL PEDESTAL WARRANTY ..................................................................................... 2 DRYER SAFETY .............................................................................. 3 WARRANTY INSTALLATION INSTRUCTIONS .................................................. 5 Tools and Parts ............................................................................ 5 ONE YEAR LIMITED WARRANTY Options ..................................
ページ3に含まれる内容の要旨
PRODUCT RECORD PEDESTAL PRODUCT RECORD In the space below, record your complete model number, serial In the space below, record your complete model number, serial number, and purchase date. You can find this information on the number, and purchase date. You can find this information on the model and serial number label located on the product. model and serial number label located on the product. Have this information available to help you obtain assistance or Have this information available to h
ページ4に含まれる内容の要旨
In the State of Massachusetts, the following installation instructions apply: [] Installations and repairs must be performed by a qualified or licensed contractor, plumber, or gasfitter qualified or licensed by the State of Massachusetts. [] If using a ball valve, it shall be a T-handle type. [] A flexible gas connector, when used, must not exceed 3 feet. IMPORTANT SAFETY INSTRUCTIONS WARNING: To reduce the risk of fire, electric shock, or injury to persons when using the dryer, follow basic pre
ページ5に含まれる内容の要旨
INSTALLATION INSTRUCTIONS Gather the required tools and parts before starting installation. Pedestal Read and follow the safety instructions provided with any tools listed here. Are you placing the dryer on a pedestal? You can purchase a • Level 8" or 10" pipe wrench pedestal separately for this dryer. This pedestal will add about 10" (25.4 cm) to the height of your unit for a total height of 8" or 10" adjustable • Vent clamps approximately 46" (116.8 cm). wrench (for gas • Knife connections) Fo
ページ6に含まれる内容の要旨
Alevel floorwithamaximum slope of1"(2.5 cm)under entire Custom undercounter installation - Dryer only dryer. (Ifslope isgreater than1"[2.5cm],install Extended Dryer FeetKit,PartNo.279810.) Clothes maynottumble 2" • _ properly andautomatic sensor cycles may notoperate correctly ifdryerisnotlevel. 36" rnin • Foragarage installation, youwillneed toplace thedryer at least 18"(46cm)above thefloor. Ifusing apedestal, youwill '%1I IJ need 18"(46cm)tothebottom ofthedryer. 1"* _ _ 27"---tb-_-- 1"* Donoto
ページ7に含まれる内容の要旨
Mobile home - additional installation requirements Minimum installation spacing for cabinet installation This dryer is suitable for mobile home installations. The installation must conform to the Manufactured Home [] The dimensions shown are for the minimum spacing allowed. Construction and Safety Standard, Title 24 CFR, Part 3280 (formerly the Federal Standard for Mobile Home Construction [] For cabinet installation, with a door, minimum ventilation and Safety, Title 24, HUD Part 280). openings
ページ8に含まれる内容の要旨
• Must include y8"NPT minimum plugged tapping accessible for test gauge connection, immediately upstream of the gas connection to the dryer (see illustration). • Must include a shutoff valve: An individual shutoff valve must be installed within 6 feet (1.8 m) of the dryer in accordance with the National Fuel Gas Code, ANSI Z223.1. The location should be easy to reach for opening and closing. Explosion Hazard A C E Use a new CSA International approved gas supply line. ilill i Install a shut-off v
ページ9に含まれる内容の要旨
Dryer gas pipe Burner input requirements • The gas pipe that comes out through the rear of your dryer has a %" male pipe thread. Elevations up to 10,000 ft (3,048 m): • The design of this dryer is certified by CSA International for use at altitudes up to 10,000 ft (3,048 m) above sea level at *6¼" the B.T.U. rating indicated on the model/serial number plate. (15.9 cm) Burner input adjustments are not required when the dryer is operated up to this elevation. Elevations above 10,000 ft (3,048 m):
ページ10に含まれる内容の要旨
Elbows 45 °elbows provide better airflow than90 °elbows. Choose your exhaust installation type Recommended exhaust installations Typical installations vent the dryer from the rear of the dryer. Other installations are possible. B Good Better Clamps Use clamps to seal all joints. ......................... F Exhaust vent must not be connected or secured with screws i ..................................... i G or other fastening devices that extend into the interior of the duct. Do not use duct tape
ページ11に含まれる内容の要旨
Alternate installations for close clearances Determine vent length and elbows needed for best Venting systems come in many varieties. Select the type best for drying performance your installation. Two close-clearance installations are shown. Refer to the manufacturer's instructions. • Use the Vent system chart below to determine type of vent material and hood combinations acceptable to use, • NOTE: Do not use vent runs longer than those specified in the Vent system chart. Exhaust systems longer
ページ12に含まれる内容の要旨
1= Remove the red cap from the gas pipe. 2. Using a wrench to tighten, connect the gas supply to the dryer. Use pipe joint compound on the threads of all non- flared male fittings. If flexible metal tubing is used, be sure Excessive Weight Hazard there are no kinks. Use two or more people to move and install dryer. Failure to do so can result in back or other injury. 1. To protect the floor, use a large flat piece of cardboard from the dryer carton. Place cardboard under the entire back edge of
ページ13に含まれる内容の要旨
Remove the 6 Phillips head screws to release the outer door assembly from the inner door assembly, as indicated below. See illustration. It is important that you remove only the 1. Using a 4" (10.2 cm) clamp, connect vent to exhaust outlet in 6 indicated screws. dryer. If connecting to existing vent, make sure the vent is clean. The dryer vent must fit over the dryer exhaust outlet and inside the exhaust hood. Make sure the vent is secured to exhaust hood with a 4" (10.2 cm) clamp. 2. Move dryer
ページ14に含まれる内容の要旨
5. Place the inner door assembly inside the outer door 2. Check for fingerprints on the glass. Clean glass if necessary. assembly. To fit correctly, the inner door assembly edge fits 3. Close door and check that it latches securely. completely inside the outer door assembly edge. 6. Reassemble the inner and outer door assemblies with the 6 screws. 1. Check that all parts are now installed. If there is an extra part, go back through the steps to see which step was skipped. 2. Check that you have
ページ15に含まれる内容の要旨
DRYER USE STATUS AUTO MODIFIERS & OPTIONS Power CYCLES Delicate _r,E 7L_4_. Wet ? @ TIMED Damp _ Casual CYCLES i[ Medium High Cool Down _ Normal Timed _cle Ad'ust I Medium igh Wrinkle Clothes Guard DW1 O_ _ Normal More Jeans Dry Express Dry O Less I Extra Low Low Wrinkle Guard Controls Locked _ Touch Up %J Check Lint Screen 6 Air Only Dryness Level ATO r_{ ES Orq¥ 0 Cycle Signal Temperature tOC_/Uf_L_K CONY_O{_ loJus_sTIM_CYC_!S ONtv Explosion Hazard Fire Hazard Keep flammable materials and vapo
ページ16に含まれる内容の要旨
To use a Timed Cycle Select a Timed Cycle. Properly loading your dryer can lower your utility bill and prolong Press MORE TIME or LESS TIME until the desired drying the life of your garments. time is displayed. Tap MORE TIME or LESS TIME and the time will change by 1-minute intervals. Press and hold Loading suggestions MORE TIME or LESS TIME, and the time will change by • Load the dryer by the amount of space items take up, not by 5-minute intervals. their weight. NOTE: The Timed Cycle Adjust fe
ページ17に含まれる内容の要旨
Cycle tips Clothes Dry • Dry most loads using the preset cycle settings. The Clothes Dry light illuminates when the drying cycle is finished. This indicator stays on during WRINKLE GUARD ®. • Refer to the Auto Cycles or Timed Cycles Preset Settings chart (in the "Cycles" section) for a guide to drying various WRINKLE GUARD ® loads. The WRINKLE GUARD ®light illuminates when this option is • Drying temperature and Dryness Level are preset when selected. This indicator stays on with Clothes Dry. yo
ページ18に含まれる内容の要旨
Auto Cycles Preset Settings Use Modifiers to select temperatures for the Timed Cycles only. Auto Cycles Load Type Temperature Time* Press Temp Adjust until the desired temperature setting (Minutes) illuminates. Temperature modifiers cannot be used with the Auto Cycles. HEAVY DUTY High 45 Heavyweight, towels i High Medium High JEANS Medium High 55 Denim pants, jackets Medium NORMAL Medium 40 Low Business clothes, corduroys, sturdy work Extra Low clothes Air 0nly CASUAL Low 35 Permanent press, 0 s
ページ19に含まれる内容の要旨
You can customize your cycles by selecting options. The dryer rack is shipped in place in your dryer. Remove and discard any packing material before use. Use the TUMBLE FREF M Non-Heated Dryer Rack for items that O WrinkleGuard you do not want to tumble dry, such as sweaters. To use the dryer rack Do not remove the lint screen. 1. Open dryer door. @LDTO CycleSignal LOCKJUNLOCKCON JR0½ WRIN KLE GUARD _ WRINKLE GUARD _ prevents wrinkles that form when you cannot unload the dryer promptly at the en
ページ20に含まれる内容の要旨
This chart shows examples of items that can be rack dried and the suggested cycle, temperature setting and drying time. Actual drying time will depend on the amount of moisture items hold. Every load cleaning Rack Dry Setting Temp. Time* The lint screen is located in the door opening of the dryer. The control panel has an indicator light to remind you to clean the lint Wool Sweaters Timed Low 60 screen before each load. A screen blocked by lint can increase Block to shape and lay flat on Cycles
