ページ1に含まれる内容の要旨
Owner's Manual & Assembly Instructions
WPOI
Model No. 697.68222
ARROW
CAUTION: SOME PARTS HAVE SHARP EDGES. CARE
MUST BE TAKEN WHEN HANDLING THEVARIOUS PIECES
715500109 TO AVOI D A MISHAP. FOR SAFETY SAKE, PLEASE READ
SAFETY INFORMATION PROVIDED IN THIS MANUAL
BEFORE BEGiNNiNG CONSTRUCTION.WEAR GLOVES
BUiLDiNG DiMENSiONS * Size rounded offtothe nearest foot o WHENHANDLING METALPARTS.
Exterior Dimensions interior Dimensions Door
•Approx. Foundation Storage Area (Roof Edge to Roof Edge) (Wail to W
ページ2に含まれる内容の要旨
BEFORE YOU BEGIN.... A2 Owner's Manual Before beginning construction, check local building codes regarding footings, location and other requirements. Study and understand this owner's manual. easier and more Important information and helpful tips will make your construction enjoyable. Assembly Instructions: Instructions are supplied in this manual and contain all appropriate information for your building model. Review all instructions before you begin, and during assembly, follow the step sequen
ページ3に含まれる内容の要旨
PLAN AHEAD.... A3 Watch the Weather: Be sure the day you select to install your building is dry and calm. Do not attempt to assemble your building on a windy day. Be careful on wet or muddy ground. Teamwork: Whenever possible, two or more people should work together to assemble your building. One person can position parts or panels while the other is able to handle the fasteners and the tools. Tools and Materials: These are some basic tools and materials you will need for the construction of you
ページ4に含まれる内容の要旨
SAFETY FIRST.... A4 Safety precautions are important to follow throughout the construction of your building. ,,Care must be taken when handling various ,,Practice caution with the tools being used in the pieces of your building since some contain assembly of this building. Be familiar with the sharp edges. Please wear work gloves, eye operation of all power tools. protection and long sleeves when assembling or performing any maintenance on your build- ing. safety_ L safetyedge ,,Keep children an
ページ5に含まれる内容の要旨
CARE & MAINTENANCE.... A5 Web Finish: For long lasting finish, periodically clean and wax the exterior surface. Touch- up scratches as soon as you notice them on your unit. Immediately clean the area with a wire brush; wash it and apply touch-up paint per manufacturer's recommendation. Roof: Keep roof clear of leaves and snow with long handled, soft-bristled broom. Heavy amounts of snow on roof can damage building making it unsafe to enter. In snow country, Roof Strengthening Kits are available
ページ6に含まれる内容の要旨
ACCESSORIES.... A6 WEB ROOF STRENGTHENING FLOOR FRAME KITS (heavy snow load) KITS Extra roof beams and gable braces designed for added protection against heavy snow accumulation. Increases the strength of your roof by 50%. ANCHOR KITS Model No. AK4 MODELS FB47410, FB5465, FB106-A FB109-A and FB1014-A Anchor Kit contains heavy-duty steel augers, 60' (18m) of steel cable and 4 cable A simple newfloorframe system made of heaw-duty, hot-dipped galvanized steel. Use as foundation for plywood, sand or
ページ7に含まれる内容の要旨
THIS PAGE WAS LEFT BLANK INTENTIONALLY 7
ページ8に含まれる内容の要旨
THIS PAGE WAS LEFT BLANK INTENTIONALLY 8
ページ9に含まれる内容の要旨
Foundation AQ09 OPTION 1: ARROW FLOOR FRAME KIT: No.FB1014-A or 68387-A) Arrow has the best base for your building in this simple kit. It keeps stored items above the ground. This kit should be used with one of the following: A. To support a plywood deck B. To be filled with sand. We recommend the combined use of 1. an ARROW FLOOR FRAME KIT and 2. an ARROW ANCHORING KIT as an effective method of securing the building to the ground. Allow I - 2 hours for construction. OPTION 2: Wood Platform If y
ページ10に含まれる内容の要旨
Anchoring AI0 It is important that the entire floor frame be anchored after the building is erected. Below are recommended ways of anchoring. Arrow Anchoring Kit: (Model No. AK4 or 60298) Anchoring into Wood/Post: Recommended for use with any suggested base. Use 1/4" Wood Screws. There are 1/4" (0,63cm) dis. Contains: 4 Anchors with Cable, Clamps and holes provided in the frames for proper anchoring. installation instruction. , & OVER THE BEAMS AND INTO THE GROUND Arrow Anchoring Kit: (Model No.
ページ11に含まれる内容の要旨
Hardware WP 11 Remove from bag of screws and save for the last step 65900A #10Bx1/2" (13mm) 65923 65004 65103 Black Screw (8) #8-32x3/8" (10mm) #8Ax5/16" (8mm) #8-32 He× Nut (236) (Packed with Screws) Bolt (236) Screw (416) 66646 65109 67468 66045 Washer (491) #8-32 Acorn Nut (4) Peak Cap (6) Handle (2) (13 sheets of 40) (Packed with Screws) (Arrow Logo) / 66183 66769 66382 Roof Trim Cap 6228 Door Slide (4) Lower Door Guide (4) (2 right & 2 left) Track Support (2) 67545 21' 67293 10' Weather Str
ページ12に含まれる内容の要旨
Parts List WPI2 Assembly Part Part Quantity Check Key No. Number Description In Carton List 1 3719 Door Handle Brace 2 2 9373 FrontWall Panel 2 3 6514 Corner Panel 4 4 6108 2 Large Right Gable 5 6109 2 Large Left Gable 6 6114 2 Small Right Gable 7 6115 Small Left Gable 2 2 8 10510 Right Roof Panel Left Roof Panel 2 9 10511 10 10497 Horizontal Door Brace 4 11 6278 Vertical Door Brace 2 12 6515 Wall Panel 10 13 6538 Roof Panel 6 14 10475 1 Right Door 15 10475 Left Door 1 16 9369 DoorJamb 2 17 6752
ページ13に含まれる内容の要旨
Assembly by Key No. WP13 13
ページ14に含まれる内容の要旨
• 8934 Ramp (1) ® Parts Needed For ® • 9367 Front Floor Frame (2) • 8936 Rear Floor Frame (2) Step 1 Floor Frame Assemblies • 10392 Side Floor Frame (4) SV14 The front floor frame is made up of three pieces. The side floor frames and the rear floor frame are made up of two pieces. The holes in these 8934 . . pieces will align when the pieces are positioned with correct amount of overlap. The illustrations below show 9367 the proper overall length for the sides, rear and front. Proceed as follows
ページ15に含まれる内容の要旨
• 5986 Rear Wail Angle (2) k._l,p_+e- Z.,_It ® Parts Needed For ® + 103+9 RearWallChannel(2) Frame Assemblies ® 10390 Side Wall Channel (4) Q 10394 Side Wall Angle (4) SR15 The main frame pieces reinforce the •, I ILl RearWall Channel walls. These pieces will later be in- 10389 L 118 1/8" 300,0cm stalled in the center and at the top edge of the side walls and the rear wall. Proceed as follows: 10389 1 Overlap the rear wall channel & pieces as shown in the figure and ill fasten the two pieces tog
ページ16に含まれる内容の要旨
® Parts Needed For ® @ 10397 Roof Beam (8) Step 3 Roof Beam Assemblies SV16 The roof beams join the two gables and support the roof panels. The main roof beam is made up of four pieces overlapped back to back at the cen- ter. The left and right roof beam as- semblies are made up of two pieces. Hint: These pieces are force-fitted, 10397 so you may have to press hard to join them together. 1 Place one end of a roof beam inside another roof beam so that the 142 3/8" 361,6cm six holes in each piece
ページ17に含まれる内容の要旨
• Parts Needed For ® • 6403 Door Track Splice (1) • 9366 Door Track (2) Step 4 Door Track Assembly A17 NOTE: Door Track Splice (painted part) The door track assembly supports the sliding doors and reinforces the front wall. It is made up ofthree pieces. 6403 1 Using the door track splice, (painted), join the door track (galvanized) pieces end-to-end as shown. 9366 :2 Insert four screws from the under- 9366 side only. 66769 Long Leg Hint: The holes in the top side of the door track assembly are f
ページ18に含まれる内容の要旨
• Front Floor Assembly (1) ® Parts Needed For • • Side Floor Assembly (2) Step 5 Floor Frame • Rear Floor Assembly (1) SWI8 RIGHT, REAR 1 Place the floor frame pieces that 8936 you assembled earlier on the foun- dation. Assemble the fourcorners of the floor frame using two screws at each corner as shown. At the front corners fasten bolts through from the bottom with nuts on top. 9367 L 2 Measure the floor frame diago- When Diagonal Measurements nally. When the diagonal measure- are Equal the Flo
ページ19に含まれる内容の要旨
• 6515 Wail Panel (2) ® Parts Needed For ® • 9373 Front Wall Panel (2) Corners Step 6 • 6514 Corner Panel (4) SRI9 NOTE The remainder of the building assembly requires many hours and more than one person. Do not continue beyond this point Wide Side if you do not have enough time to com- plete the assembly today, A partially REAR assembled building can be severely 6514 damaged by light winds, Each screw and bolt in the wall re- quires a washer. TOP VIEW SIDE SIDE 1 Position a corner panel at the
ページ20に含まれる内容の要旨
• Door Track Assembly (1) ® Parts Needed For • • Rear Wall Angle Assembly (1) Step 7 • Side Wall Angle Assembly (2) Top Frames WP20 The top frame pieces give rigidity to the walls and provide a surface for attaching the gables which support the roof. I Fasten the rearwall angle across the inside top of the rear wall using so rews. 2 Fasten the sidewall angles across the inside top of the side panels us- ing screws. Side wall angles must overlap rear wall angle in corners. Must Face LongLeg 3 Fas
