ページ1に含まれる内容の要旨
ページ2に含まれる内容の要旨
A. INTRODUCTION Welcome to the Krell family of audio components. You have joined a select group of discriminating listeners who enjoy the finest in music reproduction. Krell Digital is dedicated to the development of techno- logically advanced components for the reproduction of digitally recorded music. These designs continue the Krell tradition of uncompromising performance through leading-edge technology. This Owner’s Reference is divided into several sections, each designed to perform a diffe
ページ3に含まれる内容の要旨
B. TABLE OF CONTENTS 3 FCC COMPLIANCE STATEMENT 4 UNPACKING AND ASSEMBLY 5 BASIC INSTALLATION AND OPERATION 6 OPERATION OF THE CD TRANSPORT 7 REMOTE CONTROL 9 QUESTIONS AND ANSWERS 12 SPECIFICATIONS 14 WARRANTY AND SERVICE INFORMATION 2
ページ4に含まれる内容の要旨
C. FCC COMPLIANCE STATEMENT WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compli- ance could void the user’s authority to operate the equip- ment. Note: This equipment has been tested and found to com- ply with the fimlts for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interfer- ence in a residentiaf installation. This equipment gener- ates, uses, an
ページ5に含まれる内容の要旨
D. UNPACKING AND ASSEMBLY 1. Open the box and remove the top layer of protective foam. The following items will now be visibIe: 1 CD-1 integrated CD player 1 ’ AC power cord 1 CD- 1RC RemOte Control 3 AAA batteries for CD-1RC packet containing the Owners Reference and 1 warranty card NOTE: If any of these items are not included please contact your authorized dealer immediately f6r assis- tance. 2. Remove the contents from the second layer of foam and set them aside for later use. Carefully remov
ページ6に含まれる内容の要旨
E. BASIC INSTALLATION AND AND CONNECTIONS 1. Place the unit on a clean level surface away from excessive heat, moist.ure or light. Ideally, the CD-1 should be placed on the top of an audio component stacl~, on top of a cabinet, or any rigid open-air platform. 2. Connect the AC power cord to the back of the unit. Once the power cord is secured plug the cord into an AC outlet. When the CD-1 is connected to the AC outlet you will hear a soft clicking sound. The display on the front panel may illumi
ページ7に含まれる内容の要旨
Care should be taken in selecting the type of cable used to link the CD- 1 to your processor. If coaxial cable is to be used it should be 75o1~m, non-capacitive, with a band- width in excess of 10MHz to prevent dropout errors. CAUTION: The CD-1 digital output is not designed to connect directly to any preamp or analog signal proces- sor. F. OPERATION OF THE CD TRANSPORT . Turn t_he CD transport On by pressing t.he POWER ~ utton, l-’ress the Open/Close button and the transport drawer will open. S
ページ8に含まれる内容の要旨
G. REMOTE CONTROL 1. Operating functions of the Remote Control are de- scribed below: The PLAY button will start playing the disc from track 1. The STOP/CM button will stop the disc from playing and clear all program memory. The NEXT button will move forward one track. The PREV button will move backward one track. The PAUSE button will temporarily stop the music or a track selection program; Press the PAUSE button again to resume play from the same point. The >> button will scan forward within a
ページ9に含まれる内容の要旨
c. Once you have finished your programming, push the PROGR button again. The mactiine will review the tracks you have selected. - d. Press the PLAY button and the program will begin. Press STOP to defeat the Program function. e. Press the REPEAT button and the machine will pla.y your selected tracks continuously in the same order they were programmed. BATTERY INSTALLATION 1. Turn the remote control over onto its front and slide the battery cover to the left until it is free from the con- trol. 2
ページ10に含まれる内容の要旨
H. QUESTIONS AND ANSWERS Q. I have installed the CD-1 but the "Error" signal flashes when I press PLAY. What should I do? A. 1. Check to see if you removed the transport screws from the bottom of the unit as stated in the UNPACKING AND ASSEMBLY section of this manual. 2. Make sure the CD is centered in the drawer, free to move and not wedged into the drawer. 3. Make sure there is nothing in the transport receptacle with the CD. 4. Try another CD CAUTION: Should none of the above be the cause of
ページ11に含まれる内容の要旨
Q. How do I gain access to a specific index with in a track? A. Start the disc playing and press the Scan Forward button until the next sequential index number appears in the display under the index column. Q. I own many CD’s which have CD Rings on them. Am I able to use these dises with the CD-1 ? A. Yes, the CD-1 will accept discs with "CD Rings". Due to their very low mass they will not damage the , CD-1 transport. While we can neither affirm or deny tlae benefits derived from the use of CD R
ページ12に含まれる内容の要旨
I. SPECIFICATIONS TRANSPORT Philips CDM-1 MK II with Hall effect motor; swing-arm design in a unicast frame. LASER Single beam with glas~: lens. DAC Single Bit with 20 Bit resolution DIGITAL OUTPUTS 1 Fibre Optic via standard interface 1 Coaxial via RCA connector. 1 AT&T Fibre Optic via ST connector (optional) ANALOG OUTPUTS 1 Single-ended output via RCA connectors 1 Balanced output via XLR connectors Balanced XLR output pin configuration p!n 1 Ground (shield) p!n 2 0 degrees (non-inverting) pin
ページ13に含まれる内容の要旨
¯ l. WARRANTY AND SERVICE INFORMATION There are no user-serviceable parts inside the CD-1. The CD-1 has a limited w, arra.nty of t~h.ree years parts and " labor on transport-relatecl parts, five years parts and labor on electronic parts, in~!udIng return freight. The wanl.anty per!od, begins on_the d~ite of purchase and is activated with the return ot the enclosed Warranty Card and a copy of the Sales receipt. Please return the completed warranty card immediately after successful installation an
ページ14に含まれる内容の要旨
0 / 0 / 0 I 0 I DIGITAL INC. 0 / KRELL DIGITAL INC. 35 HIGGINS DRIVE MILFORD CT 06460 SALES 203-874-3139 FAX 203-878-8373 COPYRIGHT 1991 KRELL DIGITAL INC. (CD19110)
