ページ1に含まれる内容の要旨
Instructions-Parts
™
AirPro Pressure
Feed Airspray Gun
312414D
Conventional, HVLP, and compliant guns for specialty industrial applications.
100 psi (0.7 MPa, 7 bar) Maximum Air Inlet Pressure
300 psi (2.1 MPa, 21 bar) Maximum Fluid Inlet Pressure
Important Safety Instructions
Read all warnings and instructions in
this manual. Save these instructions.
See page 2 for model information.
ti1109
ll 2 G
ページ2に含まれる内容の要旨
Contents Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Pressure Relief Procedure . . . . . . . . . . . . . . . . . 9 General Metal with Stainless Steel Tip . . . . . . . . 3 Apply Fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Automotive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Volatile Organic Compounds (VOC) Regulation . 9 Stain . . . .
ページ3に含まれる内容の要旨
Models Models General Metal Spray Guns Conventional HVLP Compliant Max. Max. Max. Orifice HVLP/Compliant HVLP/Compliant HVLP/Compliant Size Air Pressure Air Pressure Air Pressure in. (mm) Model Series psi (MPa, bar) Model Series psi (MPa, bar) Model Series psi (MPa, bar) 0.020 (0.5) 288726 A N/A 288935 A 19 (0.13, 1.3) 288942 A 29 (0.2, 2.0) 0.030 (0.8) 288929 A N/A 288936 A 19 (0.13, 1.3) 288943 A 29 (0.2, 2.0) 0.042 (1.1) 288930 A N/A 288937 A 19 (0.13, 1.3) 288944 A 29 (0.2, 2.0) 0.055 (1.4
ページ4に含まれる内容の要旨
Models Stain Conventional HVLP Compliant Max. Max. Max. Orifice HVLP/Compliant HVLP/Compliant HVLP/Compliant Size Air Pressure Air Pressure Air Pressure in. (mm) Model Series psi (MPa, bar) Model Series psi (MPa, bar) Model Series psi (MPa, bar) 0.020 (0.5) 288958 A N/A 288960 A 22 (0.15, 1.5) 288962 A 29 (0.2, 2.0) 0.030 (0.8) 288959 A N/A 288961 A 22 (0.15, 1.5) 288963 A 29 (0.2, 2.0) 0.040 (1.0) 289109 A N/A 289110 A 22 (0.15, 1.5) 289111 A 29 (0.2, 2.0) Waterborne Conventional HVLP Compli
ページ5に含まれる内容の要旨
Warnings Warnings The following warnings are for the setup, use, grounding, maintenance, and repair of this equip- ment. The exclamation point symbol alerts you to a general warning and the hazard symbol refers to procedure-specific risk. Refer back to these warnings. Additional, product-specific warnings may be found throughout the body of this manual where applicable. WARNING FIRE AND EXPLOSION HAZARD Flammable fumes, such as solvent and paint fumes, in work area can ignite or explode. To h
ページ6に含まれる内容の要旨
Gun Selection WARNING PRESSURIZED EQUIPMENT HAZARD Fluid from the gun/dispense valve, leaks, or ruptured components can splash in the eyes or on skin and cause serious injury. �Follow Pressure Relief Procedure in this manual, when you stop spraying and before cleaning, checking, or servicing equipment. � Tighten all fluid connections before operating the equipment. � Check hoses, tubes, and couplings daily. Replace worn or damaged parts immedi- ately. TOXIC FLUID OR FUMES HAZARD Toxic fluids
ページ7に含まれる内容の要旨
Setup Setup 5. Connect a fluid hose to the fluid inlet fitting. See FIG. 1. At least one hose must provide a static ground to the gun. Connect Air and Fluid Lines 1. Shut off the air supply. 2. Install a shutoff valve (not supplied) down- fluid inlet air inlet stream of the air regulator to shut off gun air. FIG. 1 ti11094a 3. Install an inline air filter (not supplied) to 6. Connect other end of the fluid hose to a clean and dry the gun air supply. regulated fluid supply line. 4. Connect a
ページ8に含まれる内容の要旨
Setup 7. To reduce fluid flow, turn the fluid control Adjust Spray Pattern valve clockwise. 1. Rotate the air cap to achieve desired spray pattern. See FIG. 2. � If the fluid control valve is turned clock- wise all the way, the gun will emit only air. � If you cannot achieve the correct fluid flow with the fluid control valve, a differ- ent sized nozzle may be necessary. For smaller fluid flow, use the next size smaller nozzle. For a larger fluid flow, use the next size larger nozzle. ti
ページ9に含まれる内容の要旨
Operation Operation See Troubleshooting, page 12, if you experience an irregular pattern. Pressure Relief Procedure When using the HVLP spray gun, instead of a conventional airspray gun, you may need to use a slightly slower hand movement and make fewer passes with the gun to coat a part. Trapped air can cause the pump to cycle This is due to the reduced spray velocity pro- unexpectedly, which could result in serious duced by lower HVLP air pressures, along with injury from splashing or mo
ページ10に含まれる内容の要旨
Daily Gun Maintenance Flush Daily Gun Maintenance Flush before changing colors, before fluid can dry in the equipment, at the end of the day, before storing, and before repairing equip- ment. Flush at the lowest pressure possible. Follow Pressure Relief Procedure, page 9, Check connectors for leaks and tighten as nec- when you stop spraying and before cleaning, essary. Flush with a fluid that is compatible checking, servicing, or transporting equip- with the fluid being dispensed and the
ページ11に含まれる内容の要旨
Daily Gun Maintenance 6. Trigger the gun while you install the fluid Clean Gun nozzle with the gun tool. Tighten the nozzle securely to 155-165 in-lb (17.5-18.6 N�m) CAUTION to obtain a good seal. � Do not submerge gun in solvent. Solvent dissolves lubricant, dries out packings, and 7. Install the retaining ring (14) and clogs air passages. air cap (13b). � Do not use metal tools to clean air cap holes as this may scratch them and distort 8. Dampen a soft cloth with solvent and wring th
ページ12に含まれる内容の要旨
Troubleshooting Troubleshooting Problem Cause Solution Spray Pattern Normal pattern. No action necessary. Right Spray Pattern Dirty or damaged air cap or Rotate air cap (13) 180°. fluid nozzle. If pattern follows air cap, prob- lem is in air cap. Clean and inspect. If pattern is not cor- rected, replace air cap. Wrong If pattern does not follow the air Heavy top cap, the problem is with the or bottom fluid nozzle (11). Clean and inspect the nozzle. If the pat- tern is not corrected, repla
ページ13に含まれる内容の要旨
Troubleshooting Problem Cause Solution Gun spitting. Air getting into paint stream. Check if fluid source is empty and fill. Tighten fluid nozzle (11). Check and tighten needle packing nut (9a). Check fluid nozzle (11) for damage. Will not spray. Fluid control valve (8) turned Adjust fluid control valve (8) too far clockwise. counterclockwise. Fluid source empty. Refill. Excessive air blowing back. Loose fluid nozzle (11). Tighten fluid nozzle (11). Damaged fluid nozzle seal Replace seal (19
ページ14に含まれる内容の要旨
Repair Repair Follow Pressure Relief Procedure, page 9. See Parts, page 16, for callout references. Disassembly 1. Unscrew retaining ring (14) to remove air 6. Remove trigger nut (22), trigger pin (21), cap (13b). Check o-rings (13a and 13c) wave washer (18), and trigger (10). and replace if necessary. 7. Unscrew needle packing nut (17) and 2. Trigger gun while unscrewing nozzle (11) to remove u-cup packing (16) and prevent needle damage. spreader (15). 3. Check o-ring (19) and replace if ne
ページ15に含まれる内容の要旨
Repair Reassembly 1. Install air control valve assembly (5) with 4. Install wave washer (18) with cupped side valve turned fully counterclockwise to out- toward the gun body. Lubricate and apply ermost position. Torque to 85-90 in-lb thread retainer to trigger pin (10). Install (9.6-10.2 N�m). trigger (10), trigger pin (21), and trigger nut (22). Torque to 15-20 in-lb 2. Install air inlet valve assembly (27) with (1.7-2.3 N�m). valve turned fully counterclockwise to out- ermost position. T
ページ16に含まれる内容の要旨
Parts Parts 3 10 8 20 3 28 3 5 6 6 20 3 7 8 1 18 3 21 3 4 19 11 9 1 13b 13c 3 26 9a 9b 4 9c 22 3 4 7 17 12 2 16 3 15 3 2 13a 14 11 23 11 10 27 6 10 36 11 ti11194a 1 Pull trigger before installing nozzle (11). 2 Insert spreader (15) with tapered end facing rear of gun. Insert u-cup (16) with open end facing front of gun. 3 Apply lubricant. 4 Apply low strength thread retainer. 5 Apply thread sealant. 6 Torque to 85-90 in-lbs (9.6-10.2 N�m). 7 Torque to 15-20 in-lbs (1.7-2.2 N�m). 8 Torque to 17
ページ17に含まれる内容の要旨
Parts --- 21✖ PIN, pivot 1 Ref. Part Description Qty. --- 22✖ PIN, pivot, nut 1 1❖ 289016 BODY, gun 1 23 289451 FITTING, air inlet 1 5 289796 VALVE, air control 1 --- 26* SPRING, compression 1 assembly 27 289142 VALVE, assembly, 1 6★* 289038 VALVE, air, assembly 1 air inlet 7* 289052 NUT, air valve, u-cup 1 --- 28* SPRING, compression 1 assembly 29 289794 TOOL, gun 1 8 289097 VALVE, fluid control 1 --- 9see NEEDLE, assembly 1 33★* TOOL, installation, 1 seal p. 20-22 (includes 9a-9c) --- 9a NUT,
ページ18に含まれる内容の要旨
Parts 18 312414D
ページ19に含まれる内容の要旨
Accessories Accessories Repair Kits Cleaning Kits Part No. Description Part No. Description 289455 Needle Packing Repair Kit 105749 Cleaning Brush 289399 Gun Repair Kit 111265 Gun Lubricant 289791 Air Cap Seal Kit 15C161 Ultimate Gun Cleaning Kit 289143 Trigger Repair Kit Test Gauges 289407 Air Valve Repair Kit 289079 Retaining Ring Kit Part No. Description 289016 Gun Handle Replacement Kit 289803 HVLP Automotive Verification 288986 Gun without needle, nozzle, or air 289563 HVLP General Metal 0
ページ20に含まれる内容の要旨
Repair Kits Repair Kits General Metal Spray Guns Nozzle Needle Needle/ Needle Tip Nozzle Size Air Cap Kit Kit Assembly Kit Nozzle Kit Kit Model Spray Type in. (mm) (13a-13c) (11, 19) (9a-9c) (9a-9c, 11, 19) (9c, 5-pack) 288726 Conventional 0.020 (0.5) 289773 289061 289270 289458 289350 288929 Conventional 0.030 (0.8) 289773 289062 289271 289459 288183 288930 Conventional 0.042 (1.1) 289773 289063 289785 289460 288184 288931 Conventional 0.055 (1.4) 289773 289064 289799 289462 288185 288932 Con
