ページ1に含まれる内容の要旨
HBR300
Bench Receiving Scale
Instruction Manual
Model
ML-29116
701 S. RIDGE AVENUE
TROY, OHIO 45374
F-34220 Rev. A (2/99)
Accept
Net Gross
kg lb
Wt. Wt.
OFF
CAPACITY
300lb x 0.1 lb / 150 kg x 0.05 kg
ZERO
Over
TARE
Under
III
LEGAL FOR TRADE
ZERO
ON NET lb
FUNCTION TARE kg
GROSS
CLEAR
ページ2に含まれる内容の要旨
ページ3に含まれる内容の要旨
Bench Receiving Scale Table of Contents INTRODUCTION .........................................................................................................................1 FCC Note...............................................................................................................................1 Verify Correctness of Weight...................................................................................................1 Installation and Setup by An Authorized Hobart Technician
ページ4に含まれる内容の要旨
ページ5に含まれる内容の要旨
Bench Receiving Scale Hobart Bench Receiving Scale (HBR300) SAVE THESE INSTRUCTIONS The HBR300 Bench Receiving Scale features a digital display Introduction with a 6-button keypad which tilts to create the best viewing angle. The scale also has adjustable legs and a level indicator to insure proper weight balance is maintained. You can operate the scale in four modes using the 6-button keypad on the display. 1. One-Touch Tare 2. Batch Weighing 3. Preset Tare 4. Upper and Lower Weight Limit This
ページ6に含まれる内容の要旨
Bench Receiving Scale Before using your scale for the first time, an Authorized Installation and Setup Hobart Service Technician must install and set up your by an Authorized scale. This includes: Hobart Technician ¥ Mounting the display and display pole to the platform. ¥ Setting an automatic shut off time as an energy saver to extend battery life. ¥ Calibrating your scale. Manual Overview The following special instructions are used in the manual: * Note A note is information that you need to k
ページ7に含まれる内容の要旨
Bench Receiving Scale When you are ready to use you scale do the following: Using the Scale ¥ Supply power to your scale either by battery (4 D-cell) or a wall-mounted adapter plug. ¥ Level the scale to maintain proper scale balance. ¥ Adjust the Display Head for easy viewing. Display Head Platter Legs Guidelines for using your scale: DO ¥ Set the scale in an area free of vibration. ¥ Set the scale on a firm, level surface. ¥ Operate in temperatures between -5°C and 40°C (23°F and 104°F). ¥ Use
ページ8に含まれる内容の要旨
Bench Receiving Scale Power can be supplied to the scale through the AC adapter Supplying Power to or optional batteries. The scale uses four (4) D-cell batteries the Scale not supplied by Hobart. To insert batteries: 1. Open the front cover of the display by pulling the tab (located on the back right side of the display) toward you. Tab Mating Terminal 2. Insert batteries using the imprinted diagram inside the battery case located on the inside front cover of the display head. To use the power
ページ9に含まれる内容の要旨
Bench Receiving Scale There are four (4) leveling legs underneath the scale platter. Leveling the Scale You may need to adjust these legs if the scale is not seated properly. Proper adjustment of these legs helps you to maintain the proper scale balance. Level the scale by turning the leveling legs right or left until the bubble in the leveling indicator is centered. Leveling Indicator Leveling Leg To adjust display head: Adjusting the Display 1. Push and hold in button located on the back righ
ページ10に含まれる内容の要旨
Bench Receiving Scale The Display Head can be adjusted for easy viewing and Display Head includes the display, display indicators, and a 6-button keypad. Weight displays in lb (pounds) or kg (kilograms) and Display indicator arrows illuminate on the display. ZERO Over Accept TARE LOW Under kg lb Net Gross III Wt. Wt. LEGAL FOR TRADE Indicator Illuminated Arrow Indicates ZERO No weight is on platter. Tare value (weight of container) displays. TARE Stable Indicator. Scale is not in motion. kg Unit
ページ11に含まれる内容の要旨
Bench Receiving Scale You can use the 6-button keypad to perform functions in Keypad two modes: ¥ Operator Mode ¥ Setup Mode Operator Mode In Operator Mode you can do the following using the keypad: ¥ Weigh products ¥ Operate one-touch tare ¥ Weigh items in batches ¥ Toggle between net and gross weight ¥ Toggle between kg and lb ZERO NET ON TARE lb FUNCTION GROSS kg OFF CLEAR KEYPAD Key Function ON Turns the scale on or off. OFF ZERO Returns scale to zero when nothing is on the platter. CLEAR TA
ページ12に含まれる内容の要旨
Bench Receiving Scale Setup Mode Setup Mode is used to program the scale with specific settings before weighing the product. In Setup Mode you can set, clear, or change: ¥ Preset tare ¥ Upper and lower weight limits ZERO NET ON TARE lb FUNCTION GROSS kg OFF CLEAR KEYPAD Key Function ON Turns the scale on or off. OFF ZERO Clears values in upper and lower weight limit and preset tare modes. CLEAR Used to enter and exit Setup Mode. FUNCTION Programs preset tare. TARE -- OR -- Allows you to move lef
ページ13に含まれる内容の要旨
Bench Receiving Scale Refer to the specific section for a further explanation of each Operating the Scale step. To operate the scale: ON OFF 1. PRESS to turn the scale on. 2. Access Setup Mode to preset tare and set upper and lower limits if desired. 3. Access Operator Mode to operate one-touch tare, weigh products, and weigh items in batches. REFER to page 14. 4. Access Setup Mode to clear or change preset tare or upper and lower weight limits if desired. ON OFF 5. PRESS to turn the scale off
ページ14に含まれる内容の要旨
Bench Receiving Scale * Note When setting the tare value, only the flashing digit can be changed. lb kg 2. PRESS to increase flashing digit by one. --OR-- NET GROSS PRESS to decrease the flashing digit by one. TARE 3. PRESS to move left one digit. The digit to the left flashes and you can increase or decrease the digit value. 4. Repeat step 3 until your tare value is set. FUNCTION 5. PRESS to return to Operator Mode. Your preset tare value displays. EXAMPLE: Mixer Bowl Tare = 8.7 lb TARE FUN
ページ15に含まれる内容の要旨
Bench Receiving Scale Clearing a Preset Tare To clear a preset tare: 1. Remove product and container from scale platter. The preset tare weight displays. TARE FUNCTION 2. HOLD DOWN and PRESS . The tare indicator and last digit flashes. ZERO CLEAR 3. PRESS . The set tare value clears, 0.0 displays, and the tare indicator and last digit flashes. FUNCTION 4. PRESS to return to Operator Mode. Setting Upper and Lower If you want the product to weigh a certain amount, you can Weight Limits set upper
ページ16に含まれる内容の要旨
Bench Receiving Scale lb kg 2. PRESS to increase flashing digit by one. --OR-- NET GROSS PRESS to decrease the flashing digit by one. TARE 3. PRESS to move left one digit. The digit to the left flashes and you can increase or decrease the digit value. 4. Repeat step 3 until your limit value is set. FUNCTION 5. PRESS . You are now in the upper limit setting mode. The Over indicator and the last digit on the display flashes. * Note FUNCTION If you want to set the lower limit only, PRESS again
ページ17に含まれる内容の要旨
Bench Receiving Scale TARE lb kg 4. PRESS 1 time, then PRESS 1 time. ZERO Over TARE Accept Under kg lb Net Gross III Wt. Wt. LEGAL FOR TRADE FUNCTION 5. PRESS . ZERO Over Accept TARE Under kg lb Net Gross III Wt. Wt. LEGAL FOR TRADE TARE lb kg 6. PRESS 2 times, then PRESS 2 times. ZERO Over TARE Accept Under kg lb Net Gross III Wt. Wt. LEGAL FOR TRADE FUNCTION 7. PRESS . ZERO Over Accept TARE Under kg lb Net Gross III Wt. Wt. LEGAL FOR TRADE Clearing Upper and Lower To clear weight limits: W
ページ18に含まれる内容の要旨
Bench Receiving Scale Access Operator Mode to operate one-touch tare, weigh Operating in Operator products, and weigh items in batches. Mode Weighing a Product Using If you do not know the package weight (tare value), use One-Touch Tare one-touch tare. To operate one-touch tare: 1. Place the container on the platter. The weight of the container displays. TARE 2. PRESS . The display changes to 0.0 and the tare indicator is lit. 3. Place the product in the container on the platter. The display wil
ページ19に含まれる内容の要旨
Bench Receiving Scale Weighing in Batches Weighing in batches allows you to add ingredients and return the weight back to zero repeatedly by pressing Tare to control the weight of each added ingredient type. To batch: 1. Place the container on the scale platter. The container weight displays. TARE 2. PRESS to make the display show 0.0. 3. Add the ingredient until the desired portion displays as the weight. 4. Repeat steps 2 and 3 for each ingredient you wish to add. 5. When done, remove the con
ページ20に含まれる内容の要旨
Bench Receiving Scale Sanitizing Do Don’t DO use 5% Chlorine Bleach (5.25% DONÕT exceed chemical Sodium Hypochlorite). manufacturerÕs recommended concentrations for sanitizer. Ratio Bleach Water Concentration 1 : 250 1 tsp. 1 gal. 200 ppm 1 : 500 1/2 tsp. 1 gal. 100 ppm DONÕT use solutions of greater than 1 : 1000 1/4 tsp. 1 gal. 50 ppm 200 ppm concentration of chlorine 1 : 2000 1/8 tsp. 1 gal. 25 ppm cleaners. * Note FDA Code of Regulations Vol. 21 require solutions containing chlorine to be of
