ページ1に含まれる内容の要旨
Complete GaraGe air Kit
66747
Set up and operatinG inStruCtionS
®
distributed exclusively by Harbor Freight t ools .
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our website at: http://www.harborfreight.com
read this material before using this product.
Failure to do so can result in serious injury.
SaVe tHiS manual.
© ®
Copyright 2009 by Harbor Freight Tools . All rights reserved. No portion of this manual or any artwork
contained herein may be reproduced in any shape or form w
ページ2に含まれる内容の要旨
Caution, used SaVe tHiS manual with the safety Keep this manual for the safety alert symbol, warnings and precautions, assembly, indicates a hazardous operating, inspection, maintenance and situation which, if not cleaning procedures. Write the product’s avoided, could result in minor serial number in the back of the manual or moderate injury. near the assembly diagram (or month notiCe is used to and year of purchase if product has no address practices number). Keep this manua
ページ3に含まれる内容の要旨
b. do not operate air compressor in ranges and refrigerators. There is explosive atmospheres, such as in an increased risk of electric shock if the presence of flammable liquids, your body is grounded. gases, or dust. The air compressor f. explore the work piece to avoid is able to create sparks resulting in contact with hidden wiring. the ignition of the dust or fumes. Thoroughly investigate the work c. Keep bystanders, children, and piece for possible hidden wiring visitors away while
ページ4に含まれる内容の要旨
persons. Any tool is dangerous in the tool. Always verify prior to using the hands of untrained users. the tool that the air source has been adjusted to the rated air pressure or f. maintain any tool with care. Keep within the rated air-pressure range. a cutting tool sharp and clean. A properly maintained tool, with sharp b. Never use oxygen, carbon dioxide, cutting edges reduces the risk of combustible gases or any bottled binding and is easier to control. gas as an air source for the to
ページ5に含まれる内容の要旨
Symbol Definitions Symbol property or statement WARNING marking concerning Risk of Hearing Loss. Wear hearing protection. WARNING marking concerning Risk of Respiratory Injury. Wear NIOSH- approved dust mask/respirator. WARNING marking concerning Risk of Explosion. Specific Safety Instructions 1. The warnings and precautions discussed in this manual cannot cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and caution
ページ6に含まれる内容の要旨
The Water Drain Valve can be opened or FunCtional deSCription closed to exhaust water from the Outlet Blocks. Turn the handle 90° parallel to valve Specifications to open, turn the handle 90° across to valve to close. Maximum Air Pressure 150 PSI Manifold Block Inlet 3/8” NPT Manifold Block Outlet 3/8” NPT initial air Kit Set up/ Ball Valve 3/8” NPT aSSemBl Y Components and Controls read the entire important SaFetY inFormation section at the beginning of this manual including all text un
ページ7に含まれる内容の要旨
area with enough extra length to allow free movement while working. air Supply 3. There must not be hazardous objects (such as utility lines or foreign t o preVent objects) nearby that will present a exploSion: hazard while working. use only clean, dry, regulated, compressed air to power this air kit. do not air Kit assembly use oxygen, carbon dioxide, note: When installing any metal combustible gases, or any connector, first wrap the threads with other bottled gas as a power thre
ページ8に含まれる内容の要旨
2. To remove the Nylon Hose (10) from 3. For surface mounting, the Nylon any compression fitting in this kit, Hose runs on the surface of the push in evenly on the release ring, drywall, and the opening in the back and pull the Hose out of the fitting. of the Manifold and Outlet Block are plugged. 3. To reattach the Hose, trim the end of the Hose above the previous crimp, installing the air Kit before attempting to reconnect to the fitting. prepare the Compressor manifold Block (8) to in
ページ9に含まれる内容の要旨
prepare outlet Block (1) problems are found, do not use air kit until repaired. 1. Attach Straight Union connector (2) to each Outlet Block (1) as needed. t o preVent Install Water Drain Valve (4) in SeriouS injur Y bottom opening of Outlet Block. Insert From a Brass Plug (7) into any unused aCCidental operation: openings in the Outlet Block. t urn off the tool, detach the air supply, safely discharge 2. Optionally, attach a 1/4” NPT quick any residual air pressure in release coupling
ページ10に含まれる内容の要旨
3. If the tool requires more force to t o preVent accomplish the task, verify that the SeriouS injur Y tool receives sufficient, unobstructed From airflow (CFM) and increase the aCCidental operation: pressure (PSI) output of the regulator t urn off any tool, detach the up to the maximum air pressure air supply, safely discharge rating of this tool. any residual air pressure in Caution! t o preVent tool the tool, and release the and aCCeSSor Y Failure, throttle and/or turn the switch r
ページ11に含まれる内容の要旨
aSSemBl Y diaGram 10 1 11 6 5 7 2 4 3 9 8 partS liSt part description Qt’y # 1 outlet Block 2 2 Straight union (1/2” x 3/8” npt) 6 3 elbow union (1/2”) 4 4 Ball Valve 2 5 Brass nipple (1/4” npt) 2 6 Brass 45° elbow (1/4” npt) 2 7 Brass plug (3/8” npt) 3 8 Compressor manifold Block 1 9 t ee Fitting (1/2”) 2 10 nylon Hose (100’ x 1/2”) 1 11 Cutting t ool (blade included) 1 REV 09g SKU 66747 For technical questions, please call 1-800-444-3353. Page 11
ページ12に含まれる内容の要旨
limited 90 da Y WarrantY Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper installat
