ページ1に含まれる内容の要旨
®
ELECTRIC FIREPLACE
OWNER’S OPERATION AND INSTALLATION MANUAL
MODELS VE32L, VE32LB, VE32LH, VE32LBH,
VE36L, VE36LB, VE36LH AND VE36LBH
PLEASE READ THIS MANUAL BEFORE INSTALLING
AND USING APPLIANCE.
WARNING: If the information in this manual is not fol-
lowed exactly, an electrical shock or fire may result caus-
ing property damage, personal injury or loss of life.
FOR YOUR SAFETY
— Do not store or use gasoline or other flammable va-
pors and liquids in the vicinity of this or any other
appli
ページ2に含まれる内容の要旨
TABLE OF CONTENTS Safety Information ............................................... 2 Maintenance ...................................................... 15 Product Specification ........................................... 3 Technical Service............................................... 22 Installation ........................................................... 3 Replacement Parts ............................................ 22 Features and Operation....................................... 7 Ac
ページ3に含まれる内容の要旨
PRODUCT SPECIFICATION 1 VE32 = 22 /4" 1 4 VE36 = 24 / " ELECTRICAL SPECIFICATIONS Voltage: 120 VAC, 60 Hz 1 4 VE32 = 16 / " TOP Total Amps: 12.5 Amps 5 5 VE32 = 15 /8" VE36 = 17 /8" Total Watts: 1500 Watts VE36 = 17" Heater Rating: 1100 Watts 7 8 1 / " Max. Bulb Rating: 100 Watts 5/8" Use only on 15 amp circuit 3 8 VE32 = 36 / " VE36 = 43" 3 8 1 VE32 = 29 / " 2 VE32 = 8" VE32 = 6 / " 1 1 VE36 = 35" 4 VE36 = 5 /4" VE36 = 5 / " VE32 = 7" VE36 = 8" 5 VE32 = 34 /8" LEFT SIDE RIGHT SIDE 1 4 VE36
ページ4に含まれる内容の要旨
IMPORTANT: To install perimeter trim kit, you INSTALLATION must install shoulder screws before installing Continued fireplace into cabinet mantel. See instructions INSTALLATION CLEARANCES included with trim kit. When installing a man- Minimum clearances to combustible construc- tel accessory, you must follow all clearance instructions (see Installation Clearances, tion are: column 1). • Top, Back and Sides of Recessed 1. Assemble cabinet mantel accessory and Cabinet . . . . . . . . . . .
ページ5に含まれる内容の要旨
IMPORTANT: If installing a perimeter trim kit, INSTALLATION you must install shoulder screws before insert- Continued ing fireplace into opening. See instructions 5. Snap assembled trim kit onto shoulder included with trim kit. If installing a mantel, screws around face to lock fireplace into you must follow clearance instructions (see mantel facing. Installation Clearances, page 4). 6. Attach mantel to base according to mantle A hearth extension is suggested for a more instructions. ple
ページ6に含まれる内容の要旨
9. Pull end of 3 wire Romex supply line INSTALLATION through universal strain relief bushing in Continued remaining cover. ELECTRICAL INSTALLATION 10. Strip back outer Romex to about 4” and connect black, white and green wires ac- WARNING: Any electrical re- cordingly using approved connectors. wiring of this appliance must be 11. Tuck tailing wires into junction box and done by a qualified electrician. replace cover using 2 remaining screws. 12. Tighten down strain adjustment on uni- Thi
ページ7に含まれる内容の要旨
INSTALLATION FEATURES AND Continued OPERATION This electronic fireplace series features a random flame effect, and a realistic log bed with glistening embers that can be adjusted for flame speed and light intensity. VE36/32LH models have a circulating heater, rated at Motor Mount 1100 Watts. Models VE36/32LB and VE36/ 32LBH include a hand detailed, textured, red-brick lining. Foam Access controls by pulling two handle tabs Shipping of upper louver until panel releases from Brace magnet
ページ8に含まれる内容の要旨
FEATURES AND OPERATION Continued ON/OFF Flame Speed Heater Switch Switch MAIN HEATER POWER HI- OFF LOW HI- OFF LOW FLAME SPEED FLAME BRIGHTNESS Flame Brightness Figure 14 - Control Panel ACCESSORy Spring Clip INSTALLATION Depress Spring Clip to Release OPTIONAL GLASS DOORS Pivot Pin Models VE36L and VE32L will accept bifold glass doors that are fully operable or a fixed Fold Bifold Door panel door that limits access to fireplace, (see After Releasing Accessories, page 23). Spring Clip to
ページ9に含まれる内容の要旨
OPTIONAL BRICk LINERS ACCESSORy Installing or Removing Brick Liner Kits INSTALLATION Brick liner kits are available for Models Continued VE36/32(L)(H) (see Accessories, page 23). Removing Bifold Glass Doors These brick panels may be installed anytime Bifold doors may be removed for replacing after fireplace installation is complete. or cleaning. Follow these steps to install left and right 1. Partially open each door and press up on brick panels: upper spring clip with a screw driver unti
ページ10に含まれる内容の要旨
Refractory ACCESSORy Refractory Retainer Bracket INSTALLATION Bracket Continued 5. Insert brick panel, beveled edge first, through firebox opening. Tilt and angle top edge into brick retainer until beveled edge contacts imager and panel is flat against firebox (see Figure 20). 6. Align hearth pan bracket over holes near lower edge of brick panel and secure with 2 pan screws provided. 7. Replace refractory bracket using 2 screws removed in step 4, page 9. 8. Repeat steps 5 through 7 for
ページ11に含まれる内容の要旨
14. Connect black heater wire to terminal ACCESSORy marked 'N-1' on heater power switch (see INSTALLATION Figure 26, page 12). Note: On alternate Continued style heaters white and black wires are connected common to terminal 'N-1' (see 7. Remove blower/heater assembly with 4 Figure 27, page 12). screws from packaging. Blower is pre- wired for convenience. Heater/ 8. Align blower assembly over hole pattern on Blower Assembly blower mount and attach with 4 pan head screws provided (see Fi
ページ12に含まれる内容の要旨
GRN Terminal Block ACCESSORy Heater/ White INSTALLATION Blower (A-B) Continued 15. Connect red heater wire to terminal marked 'L-4' on heater power switch (see Figure 26 or 27. Rocker 16. Connect one end of black jumper lead, Switch provided in kit, to power connection Red (L-4) Black (N-1) marked 'D' on terminal block and other Figure 26 - Connecting Heater Wires end to switch terminal marked 'L-5' (see Figure 26). Terminal Block Heater/ 17. Replace 2 hex screws on rear flanges of White
ページ13に含まれる内容の要旨
TROUBLESHOOTINg Note: Before troubleshooting system, make sure power to circuit from breaker or fuse panel is turned ON. The three most common causes of a malfunctioning electric fireplace are: 1. Tripped circuit breaker or blown fuse. 2. Loose or burned out light bulb. 3. Obstructed or clogged fan blower. OBSERvED PROBLEM POSSIBLE CAUSE REMEDY No operation or indicator light 1. No power to fireplace 1. Check circuit breaker or fuse at power/heater switch 2. Defective switch lamp 2. Replace def
ページ14に含まれる内容の要旨
WIRINg DIA gRAM MOTOR CUTOUT HEATER ASSEMBLY - ELECTRICAL DIAGRAM CIRCUIT WHT SPLICE CONNECTION WHT MALE CONNECTION FEMALE CONNECTION RED CAUTION: DISCONNECT FIREPLACE FROM THE ELECTRICAL SUPPLY BLK BEFORE REMOVING THIS COVER HEATER CAUTION: USE SUPPLY WIRES SUITABLE FOR 105°C OR EQUIVALENT COIL RED BLK CONTROL PANEL - ELECTRICAL DIAGRAM HEATER BLK 4 LN 1 4 LN 1 MAIN POWER POWER 5 L 5 L SUPPLY WHT - ALTERNATE CONNECTION WHT BLACK BLK HARNESS 4" BLK HARNESS 4" BLK HARNESS
ページ15に含まれる内容の要旨
5. Return power to circuit and turn main power MAINTENANCE switch and lamp power on to check opera- tion of bulbs before replacing log set. WARNING: Disconnect 6. If all bulbs are working properly, replace power before attempting any the log bed over the center opening in maintenance or cleaning to re- between rear screen and front grate. duce the risk of fire, electrical shock or personal injury. CAUTION: Make sure power is turned off at supply prior to disassembling this unit. WARNI
ページ16に含まれる内容の要旨
9. Angle control panel out through opening MAINTENANCE (see Figure 32). Continued 10. Follow these instructions in reverse order 5. Rotate control door up into control com- to reassemble control panel assembly. partment and slide on end into side of Note: Be certain that all wires, harnesses and compartment. bushings are returned to their normal position 6. Tilt out one end first then pull remaining and free of damage before reconnecting sup- door assembly through opening. ply power to the
ページ17に含まれる内容の要旨
7. Remove 4 Phillips screws on base cover MAINTENANCE and lift cover off cabinet base. See Figure Continued 36, page 18. ACCESSING IMAGING UNIT Note: Only VE32 series models have Face The imaging unit can be accessed from inside Extensions that require removal to access fireplace for servicing as follows: Imaging Unit. Model VE36 series has inner Face Panels that also require removal to ac- 1. Remove glass doors (if equipped). See Optional Glass Doors, on page 8. cess Imaging Unit. 2. Rem
ページ18に含まれる内容の要旨
5. Lift entire fan assembly off of mounts and MAINTENANCE tilt out of unit. Continued 6. Remove screws with washers and hex nuts from fan housing. 7. Mount new fan to blower mount in reverse order. 8. Slide blower assembly with spacers over mounting lugs and replace washer and Base nut at each lug. Do not over tighten. Cover 9. Attach blade connectors to posts on motor mount. Note: Wire connectors for fan motor are non-polarized and may be connected to either terminal for proper opera
ページ19に含まれる内容の要旨
MAINTENANCE Continued Note: Flame pennant should not be twisted or tangled and should hang slightly loose to allow free movement. If cord is too short or pennant is torn you must obtain a replacement flame assembly (see Replacement Parts, on page 22). 4. After connecting and adjusting flame cords, soak each knot with a drop of white wood glue or clear nail polish to prevent unraveling. Flame Cord Hook Flame Pennant Flame Spacer Figure 38 - Locating Flame Pennants 115121-01B www.desatech.com
ページ20に含まれる内容の要旨
Note: There should be no exposed bare MAINTENANCE wire at any connection. Wiring should be Continued secured with wire ties, as short as possible, REPLACING LAMP FIxTURES and kept away from fan blades. If additional Lamp fixtures may be replaced as follows: parts are required, see Replacement Parts, on page 22. 1. Turn off all power to fireplace at circuit 7. Replace each light bulb with proper color, breaker or fuse. (see Replacing Light Bulbs, page 14). 2. Locate any of 3 defective lam
