ページ1に含まれる内容の要旨
B UILT-I N R EFRIGERATION
INSTALLATION INSTRUCTIONS
ページ2に含まれる内容の要旨
CONTENTS Installation Recommendations 3 Installation Specifications 4 Installation Instructions 8 Framed Panel Installation 12 Overlay Panel Installation 16 Completing the Installation 20 Service Information 23 Specifications are subject to change without notice. Check our website, subzero.com, for the most up-to-date specifications. As you follow these instructions, you will notice WARNING and CAUTION symbols. This blocked information is important for the safe and efficient installation of Sub
ページ3に含まれる内容の要旨
BUILT-IN INSTALLATION RECOMMENDATIONS INSTALLATION RECOMMENDATIONS The importance of the installation of the TOOLS AND MATERIALS REQUIRED Sub-Zero Built-In unit cannot be overempha- The following is a list of tools and materials sized. Installation should be done by a that should be available for proper installation. qualified installer. Before you begin the installation process, it Phillips screwdriver set is recommended that you read this entire Installation Instructions book. There are key Sl
ページ4に含まれる内容の要旨
BUILT-IN INSTALLATION SPECIFICATIONS INSTALLATION SPECIFICATIONS Make sure that the actual equipment that was SITE PREPARATION shipped to you matches the design you are Make sure that the finished rough opening expecting to install. The Sub-Zero Built-In line where the Built-In unit is to be installed is offers the following design alternatives— properly prepared. Refer to the Overall Dimen- framed, overlay and stainless steel models. sions and Installation Specifications for your Each of these
ページ5に含まれる内容の要旨
BUILT-IN INSTALLATION SPECIFICATIONS OVERALL DIMENSIONS All Refrigerator | All Freezer Models ALL REFRIGERATOR 73" 73" 73" ALL FREEZER (1854) (1854) (1854) Model 601R All Refrigerator Model 601RG All Refrigerator with Glass Door 36" 36" 36" 24" Model 601F (914) (914) (914) (610) All Freezer Model 601R Model 601RG Model 601F All Refrigerator All Refrigerator All Freezer with Glass Door Width 36" (914) Width 36" (914) Width 36" (914) Height 73" (1854) Height 73" (1854) Height 73" (1854) Depth 24"
ページ6に含まれる内容の要旨
BUILT-IN INSTALLATION SPECIFICATIONS OVERALL DIMENSIONS Over-and-Under Models OVER-AND- UNDER 84" 84" 84" 84" (2134) (2134) (2134) (2134) Model 611 Model 611G with Glass Door Model 650 Model 650G with Glass Door 30" 30" 36" 36" 24" (762) (762) (914) (914) (610) Model 611 Model 611G Model 650 Model 650G with Glass Door with Glass Door Width 30" (762) Width 30" (762) Width 36" (914) Width 36" (914) Height 84" (2138) Height 84" (2138) Height 84" (2138) Height 84" (2138) Depth 24" (610) Depth 24" (6
ページ7に含まれる内容の要旨
BUILT-IN INSTALLATION SPECIFICATIONS OVERALL DIMENSIONS Side-by-Side Models 84" (2134) 36" 42" 42" 48" 48" 24" (914) (1067) (1067) (1219) (1219) (610) Model 661 Model 642 Model 685 Model 632 Model 695 Ice | Water Dispensing Ice | Water Dispensing Width 36" (914) Width 42" (1067) Width 42" (1067) Width 48" (1219) Width 48" (1219) Height 84" (2138) Height 84" (2138) Height 84" (2138) Height 84" (2138) Height 84" (2138) Depth 24" (610) Depth 24" (610) Depth 24" (610) Depth 24" (610) Depth 24" (610)
ページ8に含まれる内容の要旨
BUILT-IN INSTALLATION INSTRUCTIONS ELECTRICAL REQUIREMENTS PLUMBING REQUIREMENTS A 115 V AC, 60 Hz, 15 amp circuit breaker and For Built-In models with an automatic ice electrical supply are required. A separate maker, rough in the water supply line. Connect 1 circuit, servicing only this appliance, is a /4" OD copper line to the house supply. Use required. an easily accessible shut-off valve between the water supply and the unit. This valve is usually All Sub-Zero Built-In models are equipped w
ページ9に含まれる内容の要旨
BUILT-IN INSTALLATION INSTRUCTIONS UNPACK THE UNIT GRILLE REMOVAL Uncrate the unit, remove its wood base and In order to prevent damage to the grille and to discard the shipping bolts that hold the wood access the power cord, the top grille assembly base to the bottom of the unit. Remove all should be removed prior to moving the unit. packing materials and tape. Models 611, 611G, 650, 650G, 661, 642, 685, IMPORTANT NOTE: Do not discard the 632 and 695—framed and stainless steel: kickplate, anti
ページ10に含まれる内容の要旨
BUILT-IN INSTALLATION INSTRUCTIONS ANTI-TIP BLOCKING KIT POSITION THE UNIT To prevent the unit from tipping forward Protect any finished flooring before and provide a stable installation, the unit moving the unit into place. All Built-In must be secured in place with an anti-tip models are equipped with rollers, so you blocking device. can easily move the unit into place. If there is a solid soffit above the unit with Shut off power to the wall outlet. Plug the clearance between the unit and the
ページ11に含まれる内容の要旨
BUILT-IN INSTALLATION INSTRUCTIONS WATER LINE CONNECTION LEVEL THE UNIT To connect the ice maker water line, remove Once the unit is in position, extend the front 1 the /4" compression fitting from its plastic bag leveling legs down by turning the legs counter- and join the water supply line to the solenoid clockwise and adjust the height. The rear height valve. Refer to illustration 7 below. NOTE: adjustment can be made from the front of the 5 The water valve can be removed from the base. Turn
ページ12に含まれる内容の要旨
FRAMED PANEL INSTALLATION PANEL INSTALLATION FRAMED PANELS Before you begin installing panels, refer to the If your customer has chosen a framed design Panel Specifications for framed or overlay application, make sure that the panels you are models and be sure you are working with the about to install match dimensions listed in the panel design called for in your installation. If Framed Panel Specifications on pages 14–15. your customer has chosen the stainless steel If the thickness of the cust
ページ13に含まれる内容の要旨
FRAMED PANEL INSTALLATION MODELS 685 AND 695 FRAMED KITS With a Phillips screwdriver, remove the PARTIAL FRAMED ACCESSORY KIT handles from the freezer and refrigerator If you choose not to use custom wood panels doors. Slide the panel into the frame on the above or below the glasswell for the Model door. With the panel in position, replace the 685 or 695 framed application, a stainless steel handles. Be sure the panel is inserted insert panel will be provided with the partial PANEL completely in
ページ14に含まれる内容の要旨
FRAMED PANEL SPECIFICATIONS FRAMED DOOR PANELS FRAMED DOOR PANELS All Refrigerator | All Freezer Framed (F) Models Over-and-Under Framed (F) Models Model 601R W H Model 611 W H 1 15 1 1 Refrigerator Framed Panel 34 /8" (867) 58 /16" (1497) Refrigerator Framed Panel 28 /8" (714) 48 /16" (1221) 1 3 Freezer Framed Panel 28 /8" (714) 18 /8" (467) Raised Panel Handle Recess Location – 15 Refrigerator Panel A) 29 /32" (749) Raised Panel Handle Recess Location – 1 Refrigerator Panel A) 24 /32" (610) 1
ページ15に含まれる内容の要旨
FRAMED PANEL SPECIFICATIONS FRAMED DOOR PANELS PARTIAL FRAMED DOOR PANELS Side-by-Side Framed (F) Models Ice | Water Dispensing Framed (F) Models Model 661 W H Model 685 W H 1 11 5 11 Refrigerator Framed Panel 19 /8" (486) 67 /16" (1719) Refrigerator Partial Framed Panel 15 /8" (397) 67 /16" (1719) 5 11 5 11 Freezer Framed Panel 14 /8" (371) 67 /16" (1719) Freezer Partial Framed Panel 15 /8" (397) 67 /16" (1719) Raised Panel Handle Recess Location – Model 695 W H 5 Refrigerator | Freezer Panel A
ページ16に含まれる内容の要旨
OVERLAY PANEL INSTALLATION OVERLAY PANELS If your customer has chosen an overlay design IMPORTANT NOTE: The weight of each panel application, make sure that the panels you are assembly cannot exceed 50 lbs (23 kg). about to install match dimensions listed in the Illustration 12 below is a cross section view of Overlay Panel Specifications on pages 18–19. the three panel assembly showing placement IMPORTANT NOTE: The size of the overlay of the door/drawer/grille trim. Illustration 13 OVERLAY pane
ページ17に含まれる内容の要旨
OVERLAY PANEL INSTALLATION MODELS 685 AND 695 GLASSWELL OVERLAY GRILLE PANELS The dispenser area of Models 685 and 695 has Models 611, 611G, 650, 650G, 661, 642, 685, been engineered to enable the use of the 632 and 695: Remove the inner grille panel overlay panel application. Installing overlay assembly as described in Grille Removal, panels for these models is the same procedure page 9. Remove the top two corner screws and as for other Built-In models. The refrigerator pull away the top frame.
ページ18に含まれる内容の要旨
OVERLAY PANEL SPECIFICATIONS OVERLAY DOOR PANELS OVERLAY DOOR PANELS All Refrigerator | All Freezer Overlay (O) Models Over-and-Under Overlay (O) Models Model 601R W H Model 611 W H 7 1 7 7 Refrigerator Overlay Panel 34 /16" (875) 59 /4" (1505) Refrigerator Overlay Panel 28 /16" (722) 48 /8" (1241) 1 5 1 7 Refrigerator Spacer Panel 33 /2" (851) 58 /16" (1481) Refrigerator Spacer Panel 27 /2" (699) 47 /16" (1205) 1 15 1 1 Refrigerator Backer Panel 34 /8" (867) 58 /16" (1497) Refrigerator Backer P
ページ19に含まれる内容の要旨
OVERLAY PANEL SPECIFICATIONS OVERLAY DOOR PANELS OVERLAY GRILLE PANELS Overlay (O) Models Side-by-Side Overlay (O) Models Width Dimensions Model 661 W H Models 611 and 611G W 7 7 Refrigerator Overlay Panel 19 /16" (494) 68" (1727) Overlay Panel Width 28 /16" (722) 1 1 1 R 1 /2" /1 " efrigerator Spacer Panel 8 (470) 67 6 (1703) Spacer Panel Width 27 /2" (699) 1 11 1 Refrigerator Backer Panel 19 /8" (486) 67 /16" (1719) Backer Panel Width 28 /8" (714) 15 Freezer Overlay Panel 14 /16" (379) 68" (17
ページ20に含まれる内容の要旨
COMPLETING THE INSTALLATION SIDE PANEL INSTALLATION If you’re installing a Built-In model with side SIDE PANEL INSTALLATION OPTIONS panels, check with your installer or use one of the following Side Panel Installation Options. 1/4" (6) THICK SIDE PANEL FITTED IN TO UNIT FRAME Drill three holes equidistant in a vertical DOOR PAN HEAD SCREW 1/8" (3) THICK BATTENS section of the aluminum frame, and install pan head screws. Do not drill through model and SIDE OF SUB-ZERO UNIT serial number plate
