ページ1に含まれる内容の要旨
OWNER’S MANUAL
PLEASE CAREFULLY READ THIS ENTIRE MANUAL BEFORE
OPERATING YOUR NEW TREADMILL!
ページ2に含まれる内容の要旨
Table of Contents Product Registration . 2 Important Safety Instructions 3 Important Electrical Information 4 Important Operation Instructions ..5 Assembly instructions .6 Folding & Transport Instructions .. .17 Operation of Your New Treadmill . 18 Programmable Features .21 Target Heart Rate 23 Using a Heart Rate Transmitter . 25 Heart Rate Control Operation 26 General Maintenance. .27 Service Checklist - Diagnosis Guide . 30 Manufacturer s Limited Warranty
ページ3に含まれる内容の要旨
CONGRATULATIONS ON YOUR NEW TREADMILL AND WELCOME TO THE SPIRIT FAMILY! Thank you for your purchase of this quality treadmill from Spirit Manufacturing, Inc. Your new treadmill was manufactured by one of the leading fitness manufacturers in the world and is backed by one of the most comprehensive warranties available. Through your dealer, Spirit will do all we can to make your ownership experience as pleasant as possible for many years to come. The local dealership where you purchased this tread
ページ4に含まれる内容の要旨
Important Safety Instructions WARNING - Read all instructions before using this appliance. DANGER - To reduce the risk of electric shock disconnect your Spirit treadmill from the electrical outlet prior to cleaning and/or service work. WARNING - To reduce the risk of burns, fire, electric shock, or injury to persons, install the treadmill on a flat level surface with access to a 120-volt, 20-amp grounded outlet. DO NOT USE AN EXTENSION CORD UNLESS IT IS A 14AWG OR BETTER, WITH ONLY ONE OUTLET ON
ページ5に含まれる内容の要旨
Important Electrical Information WARNING! NEVER use a ground fault circuit interrupt (GFCI) wall outlet with this treadmill. Large switching currents of the drive motor will trip GFCI type outlets, as any appliance with a large motor. Route the power cord away from any moving part of the treadmill including the elevation mechanism and transport wheels. NEVER remove any cover without first disconnecting AC power. If voltage varies by ten percent (10%) or more, the performance of your treadmill
ページ6に含まれる内容の要旨
NEVER operate this treadmill without reading and completely understanding the results of any operational change you request from the computer. Understand that changes in speed and incline do not occur immediately. Set your desired speed on the computer console and release the adjustment key. The computer will obey the command gradually. NEVER use your treadmill during an electrical storm. Surges may occur in your household power supply that could damage treadmill components. Use caution whil
ページ7に含まれる内容の要旨
Assembly Instructions (XT375 / XT475) XT375 / XT475 / XT675 6
ページ8に含まれる内容の要旨
Assembly Pack Check List (XT375 / XT475) Step 1 5/16 x 15m/m Button Head Socket Bolt (8 pcs) Step 2 5/16 x 2 Button Head 8 x 23 x 1.5T Socket Bolt (4pcs) Curved Washer (4pcs) Step 3 5/16 x 1-1/2 8 x 23 x 1.5T Button Head Socket Bolt (2pcs) Flat Washer (4pcs) 8mm Beveled 5/16 x 2-3/4 Washer (2pcs) Button Head Socket Bolt (2pcs) XT375 / XT475 / XT675 7
ページ9に含まれる内容の要旨
Step 4 3.5 x 40m/m Self Tapping Screw (6 pcs) Tools Deck / Belt Safety Key (1pc) Lubricant (1pc) Combination M5 Allen Wrench M6 Allen Wrench (1pc) & Phillips Head Screw Driver (1 pc) XT375 / XT475 / XT675 8
ページ10に含まれる内容の要旨
!!ATTENTION: IMPORTANT UNPACKING INSTRUCTIONS. PLEASE READ BEFORE UNPACKING YOUR FOLDING TREADMILL!! Serious injury could occur if this folding treadmill is not unpacked properly. There is a Velcro strap installed around the treadmill base that prevents the treadmill from unfolding accidentally during shipping. If this strap is not removed properly the treadmill could spring open unexpectedly and cause injury if someone is standing near the treadmill when the strap is removed. To ensure your per
ページ11に含まれる内容の要旨
STEP 2 1. Mount the L&R Handle bars onto Handle bar mounting plates at the top of the upright tubes with four 5/16 x 2 Button Head Socket Bolts and four curved washers. NOTE: The L&R handlebars are different. The Right handle bar has two wires and the switches on the handle bar say “Fast and Slow” while the Left handle bar switch says “Up and Down”. STEP 3 1. Install the L & R inside console end caps onto the ends of the 1-1/4 X 2-3/8 console mounting tube. Ensure the end caps are oriented cor
ページ12に含まれる内容の要旨
Assembly Instructions (XT675) XT375 / XT475 / XT675 11
ページ13に含まれる内容の要旨
Assembly Pack Check List (XT675) Step 1 3/8" x 2.0T 10m/m Split Washer (2pcs) Beveled Washer (2pcs) 5/16 x 15m/m 3/8 x 2 Button Head Socket Bolt (6pcs) Button Head Socket Bolt (2pcs) Step 2 8m/m 8 x 23 x 1.5T Beveled Washer (2pcs) Flat Washer (4pcs) 5/16 x 1-1/2 8 x 23 x 1.5T Button Head Socket Bolt (2pcs) Curved Washer (4pcs) 5/16 x 2 5/16 x 2-3/4 Button Head Socket Bolt (4pcs) Hex Head Bolt (2pcs) XT375 / XT475 / XT675 12
ページ14に含まれる内容の要旨
Step 3 8 x 23 x 1.5T #102. 5/16 x 15m/m Curved Washer (4pcs) Button Head Socket Bolt (4pcs) 5/16 x 1-3/4 Button Head Socket Bolt (4pcs) Step 4 5 x 16m/m M5 Tapping Screw (2 pcs) Speed Nut (4 pcs) 5 x 16m/m 3.5 x 40m/m Screw (6 pcs) Self Tapping Screw (6 pcs) XT375 / XT475 / XT675 13
ページ15に含まれる内容の要旨
Tools Deck / Belt Safety Key (1pc) Lubricant (1pc) Combination M5 Allen Wrench M6 Allen Wrench (1pc) & Screwdriver (1 pc) 12m/m Wrench (1 pc) XT375 / XT475 / XT675 14
ページ16に含まれる内容の要旨
!!ATTENTION: IMPORTANT UNPACKING INSTRUCTIONS. PLEASE READ BEFORE UNPACKING YOUR FOLDING TREADMILL!! Serious injury could occur if this folding treadmill is not unpacked properly. There is a Velcro strap installed around the treadmill base that prevents the treadmill from unfolding accidentally during shipping. If this strap is not removed properly the treadmill could spring open unexpectedly and cause injury if someone is standing near the treadmill when the strap is removed. To ensure your per
ページ17に含まれる内容の要旨
STEP 2 1. Install the L & R inside console end caps onto the ends of the 1-1/4 X 2-3/8 console mounting tube. Ensure the end caps are oriented correctly and facing the correct direction (see diagram). Also ensure that the wiring is fed through the end caps. 2. Place the console onto the L & R mounting brackets at the top of the upright tubes. Then install and hand tighten the two 5/16 x 2-3/4 Hex Head bolts and flat washers through the holes in the top and front of the 1-1/4 X 2-3/8 console
ページ18に含まれる内容の要旨
XT375 / XT475 Folding Instructions Do not attempt to move the unit unless it is in the folded and locked position. Be sure the power cord is secured to avoid possible damage. Use both handrails to maneuver the unit to the desired position. To Fold The Treadmill: Make certain the treadmill is at minimum incline. Lift the treadmill running deck until it is secured by the locking telescoping tube assembly in center back of base. To Unfold The Treadmill: Apply slight forward pressure* on the tread
ページ19に含まれる内容の要旨
Operation of Your Treadmill Getting familiar with the control panel XT375 Console XT475 / XT675 Console XT375 / XT475 / XT675 18
ページ20に含まれる内容の要旨
Getting started: Power the treadmill on by plugging it into an appropriate wall outlet, then turn on the power switch located at the front of the treadmill below the motor hood. Ensure that the safety key is installed, as the treadmill will not power on without it. When the power is turned on, all the lights on the display will light for a short time. Then the Time and Distance windows will display Odometer readings for a short time. The Time window will show how many hours the treadmill has bee
