ページ1に含まれる内容の要旨
ページ2に含まれる内容の要旨
DECLARATION OF CONFORMITY Warning Manufacturer’s Name: DigiTech For your protection, please read the following: Manufacturer’s Address: 8760 S. Sandy Parkway Sandy, Utah 84070, USA Important Safety Instructions declares that the product: 1. Read these instructions. 2. Keep these instructions. Product name: HardWire CM-2 3. Heed all warnings. 4. Do not use this apparatus near water. Product option: All (requires Class II power 5. Clean only with dry cloth. adapter that conforms to t
ページ3に含まれる内容の要旨
WARRANTY: We at DigiTech are proud of our products and back-up each one with the following warranty: The warranty registration card must be mailed within ten days after purchase date to validate this warranty. DigiTech warrants this product, when used solely within the U.S., to be free from defects in materials and workmanship under normal use and service. DigiTech liability under this warranty is limited to repairing or replacing defective materials that show evidence of defect, provided th
ページ4に含まれる内容の要旨
ページ5に含まれる内容の要旨
Introduction ™ More than a remarkable achievement, HardWire represents a collection of significant improvements in effects pedals for guitar. HardWire pedals pro- vide a suite of well-known effects, each with superior tone and control. But these pedals go above and beyond their peers to provide such distinguishing features as true bypass and high voltage operation, making them essential additions to the signal chain of players who know about sound quality and demand the utmost in performanc
ページ6に含まれる内容の要旨
1 2 3 4 5 6 11 7 8 8 9 10 2
ページ7に含まれる内容の要旨
What Does This Do? 1. Level Knob - Controls the overdrive output level. Turn the knob clockwise to increase and counter-clockwise to decrease the output level. 2. DC Adapter Jack - Connect (an optional) Harman PS200R power supply to this jack. Use the proper supply for your area’s mains line voltage. 3. Low Knob - Controls the level of low frequency (bass) boost/cut. Turn the knob clockwise to increase and counter-clockwise to decrease bass level. 4. High Knob - Controls the level of hig
ページ8に含まれる内容の要旨
6. Voicing Switch - This switches between the Overdrive’s two voic- ings. Classic voicing provides the kind of gain you need for amaz- ingly crunchy rhythms. Modified voicing pushes your amp to the limits with just the extra gain you need for hot solos. 7. Input - Connect your instrument or the output of another pedal to this jack. This jack enables battery power to the pedal when con- nected. To prolong battery life, disconnect the cable from the Input jack when not in use. If the optional
ページ9に含まれる内容の要旨
10. Foot Switch - Turns the effect on and off. 11. Output - Connect this output to the input of your amplifier or the input of another pedal. Note: Use unbalanced mono instrument cables only. 5
ページ10に含まれる内容の要旨
Amplifier Setup PS200R (optional) or
ページ11に含まれる内容の要旨
Battery Operation In the event that battery power is completely depleted, HardWire pedals automatically switch into bypass. This eliminates the need to remove the pedal from your pedal chain if the battery is dead. To replace the battery, do the following: . Using the tip of a /” guitar cable, push in one of the Release Pins in on either side of the Foot Switch, and remove it from the pedal chassis. 2. Remove the battery from the battery compartment and disconnect the battery cable. .
ページ12に含まれる内容の要旨
Switch is properly fastened, both Release Pins are flush with the outer side of the pedal. Foot Switch Pedal Switch Arm 9VDC Battery Foot Switch Release Pin Battery Compartment Foot Switch Spring Release Pin Pedal Chassis
ページ13に含まれる内容の要旨
HardWire Performance Accessories The performance accessories make integrating a HardWire pedal into any pedal board a snap. The following accessories are included: • Hook-and-loop Pedalboard Pad (designed to attach to the surfaces found on most commercial pedal boards) • Foot Switch Glow Sticker (easily visible on dark stages) ™ • StompLock (keeps your settings where you want them)
ページ14に含まれる内容の要旨
Hook-and-loop Pedalboard Pad To attach the Pedalboard Pad, do the following: . Peel off the existing rubber skid pad from the bottom of the pedal. 2. Peel the adhesive protector from the back of the Pedalboard Pad. . Apply the Pedalboard Pad to the bottom of the pedal. 0
ページ15に含まれる内容の要旨
Foot Switch Glow Sticker To attach the Foot Switch Glow Sticker, do the following: . Peel the adhesive backing from the Foot Switch Glow Sticker. 2. Apply the Glow Sticker to the top of the Foot Switch.
ページ16に含まれる内容の要旨
StompLock To place the StompLock over the pedal knobs, do the following: . Set the knobs to your preferred setting. 2. Gently push the StompLock over the top of the knobs. . To remove the StompLock, gently lift one side and then the other. 2
ページ17に含まれる内容の要旨
Specifications Controls - Level, Low, High, Gain, Voice Switch, On/Off Pedal Jacks - Input, Output Input Impedance - >500 k Ω - effect on Output Impedance - k Ω - effect on Input Impedance - true hardwire bypass - effect off Output Impedance - true hardwire bypass - effect off Power Supply - V Alkaline Dry Battery or Harman PS200R V DC power supply Current Draw - 20 mA (typical at V DC) Power Consumption - 0 mW (typical w/optional PS200R power supply) Dimensions - 5.25”(L) x .
ページ18に含まれる内容の要旨
ページ19に含まれる内容の要旨
ページ20に含まれる内容の要旨
8760 South Sandy Parkway Sandy, Utah 84070 PH (801) 566-8800 FAX (801) 566-7005 HardWire and DigiTech are trademarks of the Harman Music Group Inc. Copyright - Harman Music Group Manufactured in the USA HardWire CM-2 Owners Manual 18-0665-A Please visit us on the World Wide Web at: www.digitech.com
