ページ1に含まれる内容の要旨
Installation/Operation Supplement
Washer-Extractors
Cabinet Freestanding
Coin Models
Keep These Instructions for Future Reference.
(If this machine changes ownership, this manual must accompany machine.)
Part No. 9002062R1EN
www.comlaundry.com December 2007
ページ2に含まれる内容の要旨
ページ3に含まれる内容の要旨
Installation/Operation/Supplement Introduction......................................................................................... 2 Table of Model Identification ............................................................................. 2 Safety Information.............................................................................. 3 Contents Explanation of Safety Messages........................................................... 3 Important Safety Instructions .....................
ページ4に含まれる内容の要旨
Installation/Operation Supplement Introduction Model Identification Information in this manual is applicable to these models: NX18BVPA6 NX18BVQA6 NX18BVXA6 NX30BVPA6 NX30BVQA6 NX30BVXA6 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 9002062 (EN) 2
ページ5に含まれる内容の要旨
Installation/Operation Supplement Safety Information Explanation of Safety Messages Important Safety Instructions Throughout this manual and on machine decals, you WARNING will find precautionary statements (“DANGER,” “WARNING,” and “CAUTION”) followed by specific To reduce the risk of fire, electric shock, instructions. These precautions are intended for the serious injury or death to persons when personal safety of the operator, user, servicer, and using your washer, follow these basic
ページ6に含まれる内容の要旨
Installation/Operation Supplement 9. Do not install or store the washer where it will be 19. Replace worn power cords and/or loose plugs. exposed to water and/or weather. 20. Be sure water connections have a shut-off valve 10. Do not tamper with the controls. and that fill hose connections are tight. CLOSE the shut-off valves at the end of each wash day. 11. Do not repair or replace any part of the washer, or attempt any servicing unless specifically 21. Loading door MUST BE CLOSED any time t
ページ7に含まれる内容の要旨
Installation/Operation Supplement Specifications and Dimensions General Specifications Model 18 30 Overall Dimensions 26 in. (660 mm) 30.7 in. (780 mm) Overall width 40.9 in. (1038 mm) 47.3 in. (1202 mm) Overall height 29.1 in. (739 mm) 33.1 in. (842 mm) Overall depth Weight and Shipping Information 465.2 lb. (211 kg) 716.5 lb. (325 kg) Net weight 513.7 lb. (233 kg) 782.6 lb. (355 kg) Shipping weight 3 3 3 3 22.5 ft (0.8 m ) 34.7 ft (1.3 m ) Shipping volume Wash Cylinder Information 20.9 in. (53
ページ8に含まれる内容の要旨
Installation/Operation Supplement General Specifications Model 18 30 Drive Train Information 11 Number of motors in drive train 1 HP (0.75 kW) 2 HP (1.5 kW) Drive motor power Cylinder Speeds 10-50 RPM 10-50 RPM Wash/reverse speed 85 RPM 85 RPM Distribution/drain speed 250-1000 RPM 250-1000 RPM Extract speed Centrifugal Force Data 0.03-0.74 Gs 0.04-0.91 Gs Wash/reverse centrifugal force 19-296 Gs 23-363 Gs Extract centrifugal force Balance Detection Standard Standard Vibration safety switch insta
ページ9に含まれる内容の要旨
Installation/Operation Supplement 8.7 in. (220 mm) H 40.9 in. (1038 mm) 39.8 in. (1011 mm) 14.4 in. (365 mm) 20.9 in. 2.6 in. 2.6 in. (530 mm) (65 mm) (65 mm) 26 in. 26.3 in. (670 mm) (660 mm) 2.7 in. 28.6 in. (727 mm) (69 mm) 9.1 in. 7.2 in. (231 mm) (184 mm) 6 in. (153 mm) 3 in. 1 5.5 in. (75 mm) (139 mm) 8 2 3 4 33.2 in. 5 (843 mm) 31.9 in. 7 (809 mm) 7 in. (180 mm) 27.7 in. (633 mm) 6 2.8 in. 26 in. (70 mm) (660 mm) CFD21N 18 MODEL CFD21N 1 Hot Water Connections .75 in. (19 mm) 5 Ventilation
ページ10に含まれる内容の要旨
Installation/Operation Supplement 8.7 in. (220 mm) 3.5 in. (88 mm) H 474 in. (1202 mm) 46.3 in. (1175 mm) 18.7 in. (475 mm) 2.6 in. 2.6 in. 25.5 in. (66 mm) (66 mm) (648 mm) 30.7 in. 29.9 in. (760 mm) (780 mm) 3.2 in. 32.1 in. (816 mm) 13.1 in. (82 mm) (332 mm) 10.5 in. (267 mm) 7.9 in. 8 in. (200 mm) (202 mm) 1 2 6.1 in. (155 mm) 8 3 4 7 5 36.4 in. (924 mm) 1.4 in. 38 in. (35 mm) (964 mm) 7.9 in. (200 mm) 33.5 in. (849 mm) 2.8 in. (70 mm) CFD23N 6 30 MODEL CFD23N 1 Hot Water Connections .75 in.
ページ11に含まれる内容の要旨
Installation/Operation Supplement Installation Dimensional Clearances Machine Foundation Table 1 shows recommended minimum clearances on Thoroughness of detail must be stressed with all all sides of the washer-extractor. foundation work to ensure a stable unit installation, eliminating possibilities of excessive vibration during extract. Recommended Minimum Clearances Model 18 30 CAUTION 24 in. 24 in. Minimum rear clearance Ensure that the machine is installed on a (600 mm) (600 mm) level fl
ページ12に含まれる内容の要旨
Installation/Operation Supplement After the concrete has cured and the anchors are Mounting Bolt Installation installed, proceed as follows: (If Required) 1. Place the washer-extractor adjacent to the foundation. Do not attempt to move it by pushing 1 on the sides. Always insert a pry bar or other device under the bottom of the frame of the 2 washer-extractor to move it. 3 2. Place the washer-extractor carefully over the anchors. 3. Put bolts through the machine in the anchors and faste
ページ13に含まれる内容の要旨
Installation/Operation Supplement IMPORTANT: Do NOT remove panel braces. Removing the Transport Block Refer to Figure 5. WARNING The machine must never be activated before removing the transport block. W618 To prevent damage during transportation, machine has been equipped with a transport block. To remove, proceed as follows: 1. Place machine on level ground. 2. Remove service panels and back panel. 3. At rear of machine, lift at bottom of motor and remove transport block. Refer to Figure
ページ14に含まれる内容の要旨
kW 2 AWG/mm Circuit Breaker Full Load Amps kW 2 AWG/mm Circuit Breaker Full Load Amps Wire Phase Cycle Voltage Code Model Installation/Operation Supplement Electrical Specifications Voltage Designation Standard Electric Heat P 380-415 50/60 3+N 3+N+PE Not available 9 16 12/4.0 9 Q 200-240 50/60 3 3+PE Not available 17 25 10/6.0 9 18 X 200-240 50/60 1/3 2/3+PE 6 16 14/2.5 0.75 Not available P 380-415 50/60 3+N 3+N+PE Not available 28 50 8/10.0 18 30 Q 200-240 50/60 3 3+PE Not available 13 32 8/10
ページ15に含まれる内容の要旨
< Installation/Operation Supplement Operation Control Panel 12 2 1 2 1 12 5 5 NORMAL PERM PRESS 95C 95C 6 6 WASH HOT WARM ADD NORMAL PERM PRESS BLEACH 60C 60C 7 7 RINSE WARM COLD SPIN QUICK WH AS QUICK WASH 40C 40C START DOOR 8 8 HOT WARM HEAVY SOIL DELICATE 30C 9 9 HOT COLD 11 CHM488R CHM482R 11 3 4 10 3 4 10 DOMESTIC MODELS INTERNATIONAL MODELS CHM482R CHM488R 1 Cycle 1 7 Cycle 7 2 Cycle 2 8 Cycle 8 3 Cycle 3 9 Down Edit/Change keypad 4 Cycle 4 10 Up Edit/Change keypad 5 Cycle 5 11 Start/Enter
ページ16に含まれる内容の要旨
< Installation/Operation Supplement 4. Close door by pushing door handle towards Operating Instructions machine. Refer to Figure 9. 1. Turn on main power source (circuit breaker). 2. Push black button and pull door handle away from machine to open door. Refer to Figure 7. CFD25N CFD25N Figure 9 CFD20N CFD20N 5. The default wash cycle will display. Figure 7 NOTE: Perm Press Cold (60°C) is the default cycle for coin models if none is selected. 3. Load to capacity whenever possible. DO NOT
ページ17に含まれる内容の要旨
Installation/Operation Supplement 6. If desired, select a different cycle at this point 8. Add coins to machine. As each coin is added, the before satisfying vend. The LED indicator for vend counts down to the amount remaining. that cycle will light. Refer to Figure 11. 7. Add liquid and/or powder supplies to supply 9. When applicable, add bleach to compartment 2 dispenser. Refer to Figure 11. when the ADD BLEACH LED is lit. a. Add detergent to compartment 1. 10. Press the desired wash cycle
ページ18に含まれる内容の要旨
Installation/Operation Supplement Disposal of Unit This appliance is marked according to the European directive 2002/96/EC on Waste Electrical and Electronic Equipment (WEEE). This symbol on the product or on its packaging indicates that this product shall not be treated as household waste. Refer to Figure 12. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. Ensuring this product is disposed of correctly will help
