ページ1に含まれる内容の要旨
ssem y a
Owner's Manua
O
'INSTRUCTIONAL
VIDEO
Hosted by _
Champion Barbecuer
Lloyd Davenport
ASSEMBLER / iNSTALLER:
Leave these instructions with the consumer.
Model 3600G Shown
CONSUMER / USER:
Read all of these instructions and keep them in a safe place for future reference.
FOR YOUR SAFETY FOR YOUR SAFETY
1. Do not store or use gasoline or other flammable vapors
if you smell gas:
1. Shut off gas to the appliance. and liquids in the vicinity of this or any other appliance.
2. Extinguish any op
ページ2に含まれる内容の要旨
Statement of Commitment Congratulations and thank you for your purchase of your new Great Outdoors smoker. We are pleased that you have recognized the value of the design, function, and quality of components used in this product. We believe it is among the finest on the market. If or for any reason we have failed to meet you're expectations, please allow us the opportunity to make it right by calling us toll-free: 1-800-668-5323 between the hours of 8:00 a.m. and 5:00 p.m. Eastern Standard time,
ページ3に含まれる内容の要旨
! E L! STRUCT! ! m YOUR SAFETY IS VERY IMPORTANT o FAILURE TO FOLLOW PROPER PROCEDURES AND SAFEGUARDS MAY RESULT IN SERIOUS PERSONAL INJURY OR PROPERTY DAMAGE. DO NOT use this smoker in a manner other than its intended purpose. It is NOT intended for commercial use. It is NOT intended to be installed or used in or on a recreational vehicle and/or boats. The smoker is not to be used as a heater. A Keep a fire extinguisher accessible at all times. A The use of alcohol, prescription or nonprescript
ページ4に含まれる内容の要旨
Use caution when opening the door of the smoker while in operation. Keep hands, face, and body safe from hot steam or flare-ups. Protect your nose and mouth from smoke inhalation. A DO NOT wear loose clothing while operating the smoker. Tie back long hair while operating the smoker. ALWAYS wear fully-covering shoes while operating the smoker. A Allow the smoker and its components to cool completely before conducting any routine cleaning or maintenance. A NEVER use glassware, plastic, or ceramic
ページ5に含まれる内容の要旨
Assembly Step 1 -Identifying the parts Check your package contents for these parts. If you are missing any parts, or if any parts are damaged, please call our toll-free customer service line to order parts. DO NOT RETURN YOUR SMOKER TO THE RETAILER- CALL US FIRST! 1.800.668.5323 Monday to Friday 9:00am to 5:00pro Eastern Standard Time Hardware Bags: X 1_ 1/4-20 x 3/8" Bolts (3) 1/4-20 3/8" Bolts (2) 1/4-20 Nuts (3) Handle Mounting Plate (1) part no: AZ001131 (Door Handle) InstructionalAZ001VideO
ページ6に含まれる内容の要旨
Identifying the parts - Continued Check your package contents for these parts. If you are missing any parts, or if any parts are damaged, please call our toll-free customer service line to order parts. DO NOT RETURN YOUR SMOKER TO THE RETAILER - CALL US FIRST! 1.800.668.5323 Monday to Friday 9:00am to 5:00pro Eastern Standard Time Burner Chamber Assembly Gas Control Panel Assembly AZ001120 AZ001137 Ignitor Knob NOTE: AZ001510 The knobs are not Ignitor Burner pre-assembled to the Electrode / Bras
ページ7に含まれる内容の要旨
Assem ly Step 2 m Burner Cabinet Chamber Phillips Head Screwdriver Assembly Assembly 1/4-20 x 3/8" Bolts 1/4-20 Nuts 3 Required 3 Required 1. With the cabinet in the upright position, begin by removing the door panel from the cabinet assembly by lifting it from the hinges. Set the door panel aside. This will make assembly much easier. 2. Set the cabinet assembly top side down. To prevent scratching or damaging your smoker, set the cabinet on a padded surface such as cardboard or carpet. The top
ページ8に含まれる内容の要旨
Assem ly Step 3 4 Legs Phillips Head Screwdriver HAROWAREOAG NOTE. Hardware Bag A includes 16 bolts - you will 1/4-20 x 5/8" Bolts need 14bolts forthis step. The 2 remaining bolts will 14 Req uired beused inthenext step. _!_!;:_i_;_i!_;_;_;:_;_;:_;_;:_;_;:_;_;:_;_;:_;_;:_;_;:_;_;:_;_;:_;_;:_;_;:_;_;:_;_;:_;_;:_;_;:_;_;:_;_;:_;_;:_;_;:_;_;:_;_;:_;_;:_;_;:_;_;:_;_;_i!;!_!i ¸i!i!!i!!!;!_i_;iiiiiii!;!i ¸I¸!ii!!iiiiiiiiiiiii_!!!_:i!iil ¸iii!;iiiii!! 1. Leave the cabinet upside down. DO NOT install th
ページ9に含まれる内容の要旨
Assem ly Step 4 iiiiiii Ignitor Knob Control Knob Control Panel Assembly Screwdriver i! 1. Leave the cabinet upside down. 2. Attach the Ignitor Knob and the Control Knob to the control panel as shown. Make sure the Control Knob properly seats on the keyed shaft. 3. Line up the control panel as shown. 4. The HVR stem must be inserted into the venturi as shown in Figure 1 on the following page. 5. When sliding the control panel into place, make sure the tabs capture the legs as shown in Figure 2 o
ページ10に含まれる内容の要旨
Assem y Step 4 - Continued NOTE: Instructions are repeated from the previous page. Figure 1 HVR stem The HVR stem must be inserted into the venturi as shown. Insert the 2 remaining bolts from Hardware Bag A through the tabs on the Control Panel and thread them into the mounting holes. Be sure the control panel mounting tabs are on top of the legs as shown. Remaining 2 iMPORTANT: The HVR stem must Mounting Bolts seat properly into the venturi. improper installation may cause fire outside the smok
ページ11に含まれる内容の要旨
Assem ly Step 5 3 Damper Plates Phillips Head Screwdriver HAROWARE 0AG 3/8" 10-24 Nuts 10-24 Lock Washers 10-24 x 5/8" Bolts Wrench 3 Required 3 Required 3 Required 1. Set one damper plate on top of the cabinet and line it up with the corresponding "butterfly" holes. 2. Insert a bolt from the top through the center hole. 3. From the bottom side, place a lock washer and nut on the bolt as shown, 4. Thread the nut just tight enough to keep the damper plate snug. It should be able to rotate with li
ページ12に含まれる内容の要旨
Assem ly Step Phillips Head 2 Carry Screwdriver Handles HAROWAREOAG 1/2" 5/16-18 Nuts 5/16 Lock Washers 5/16-18 x 3/4" Bolts Wrench 8 Required 8 Required 8 Required 1. Line up the carry handle with the corresponding holes on the side of the cabinet as shown. The handles must be positioned upright with the bolt holes on the bottom as shown. 2. Insert the bolts from the outside and thread the lock washers and nuts from the inside of the cabinet. 3. Firmly tighten the nuts. 4. Complete steps for bo
ページ13に含まれる内容の要旨
Assembly Step 7 ..... ;_i_@_!i_@_i_!_!ii_ii_ii_ii_iiii_ii_i_iiiii_i{_ii_!_i!_!i}_i!_i_i_!_i!_i!_!!_!i_i@_i_@_i_i_iiii_i_i_i_ ...... ii!iiiiiiii{{{{{;iii_!i_ _, i{iiiiiiii{{iiiii!!!;;ii!!_,_,s_!:iiii!i!iiiiiii!!i{ii_iii!_i_i_i_iiii!i!!i_:_ _@_i!_ii!!i!ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_iiiiiiiiiiiii_iiiiiiiii!i!!!!!i_!i!i!i!i!iiiiiiiiiiiiiiiiiiiiiiii_i_i_i_i_ii!_! !!ii_i!!i!i_!_i_ii_i_i_ii_B_iii_ii_ii_ii_ii!ii_i!!ii!i!!ii!i!_i!_iiiii_ii_i_i_i_iiii_i: Wood Chip Wood Chip Box Lid Box Stand Wood Chip Box
ページ14に含まれる内容の要旨
Assembly Step Water Bowl No tools or hardware are required for this step. 1. Slide the water bowl into the lowest rack position as shown. 2.Insert the cooking grids into any of the remaining rack positions as desired. Do not insert a grid directly over the water bowl - the bowl will restrict heat distribution. For best results, the grid wires should run front to back as shown. 3. Re-mount the door panel by sliding the door's hinge pins into the cabinet's hinge seats. 12
ページ15に含まれる内容の要旨
Assem ly Step HARDWARE BAG _ Door Handle Kit 1/4-20 x 3/8" Bolts and 1/4-20 Lock Washers (2 ea) Phillips Head Handle Spring, Screwdriver Handle Washer, Mounting Plate 1. Slide the handle washer onto the end of the door handle, followed by the handle spring as shown. 2. Feed the door handle into the hole through the front of the door panel. 3. From the back side of the door panel, insert the mounting plate over the end of the handle as shown. 4. With lock washers placed on the bolts, insert the b
ページ16に含まれる内容の要旨
Assem ly Step I • . _i_iL¸ .... _,i!iiii!i Indicator Heat HAROWAREOAG NOTE. the nut is already threaded to the back of 5/16-18 Nut the heatindicator and 1 Required re,st be removedfor assembly. 1. Remove the nut from the back of the heat indicator and insert the heat indicator into the door panel as shown. Make sure the indicator numbers are right side up. 2. From the back side of the door panel, thread the nut onto the heat indicator. 3. Double check and make sure the face of the heat indicator
ページ17に含まれる内容の要旨
Assem ly Step 1t HARDWARE BAG S-Hook Pliers Using the zip tie, secure the hose to the front leg as shown. Do not pull the zip tie tight - leave it just loose enough so that the hose can be adjusted if needed. Tying the hose to the leg helps prevent the hose from coming into contact with the hot burner chamber. Inspect the installation underneath the smoker to ensure that the hose is not rubbing any portion of the burner chamber. Place one end of the S-Hook Crimp around the regulator neck or thro
ページ18に含まれる内容の要旨
e LP Tank Connecting ALL INSTRUCTIONS AND SAFEGUARDS ON THIS PAGE MUST BE FOLLOWED TO PREVENT FIRE, DAMAGE, AND / OR INJURY. E 1. The knob on the LP tank must be closed. See that the knob is turned clockwise to a full stop. 2. Check that the control knob on the smoker is turned off. 3. Remove the protective cap from the LP tank valve and coupling nut, if present. 4. Hold the regulator in one hand and insert the nipple into the valve outlet. Be sure the nipple is centered in the valve outlet. The
ページ19に含まれる内容の要旨
e LP Tan - Continued Connecting ALL INSTRUCTIONS AND SAFEGUARDS ON THIS PAGE MUST BE FOLLOWED TO PREVENT FIRE, DAMAGE, AND / OR INJURY. Cylinders must be filled before initial use. All handling, transport, filling and storage of LP gas cylinders must be in accordance with NFPA 58 Storage and Handling of Liquid Petroleum Gases, or CAN/CGA b149.2 Propane Installation Code. Cylinders must be suitably tied down during transport. Do not place any other items on top of cylinders at any time. Cylinders
ページ20に含まれる内容の要旨
Operating Instructions Pre-Use Procedures Your smoker has been packaged with a retail store level point-of-purchase label that hangs on the front of the door panel. This label must be removed before use. To remove the label, simply cut or tear along the indicated line and pull the top portion of the label from behind the name plate. Before you cook food in your smoker, it is important to "season" your smoker. Seasoning seals the paint and interior of your smoker to enhance flavoring, durability,
