ページ1に含まれる内容の要旨
WWW.GRIZZLY.COM
3
14.4V ⁄8" CORDLESS DRILL,
DETAIL SANDER AND JIG SAW
MODEL G8594
INSTRUCTION SHEET
COPYRIGHT © 1999 BY GRIZZLY INDUSTRIAL, INC.
1821 VALENCIA ST., BELLINGHAM, WA 98227
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
NOVEMBER, 1999 PRINTED IN CHINA
ページ2に含まれる内容の要旨
ページ3に含まれる内容の要旨
SAFETY For Your Own Safety Read Instruction Manual Before Operating This Equipment The purpose of safety symbols is to attract your attention to possible hazardous conditions. This manual uses a series of symbols and signal words which are intended to convey the level of importance of the safety messages. The progres- sion of symbols is described below. Remember that safety messages by them- selves do not eliminate danger and are not a substitute for proper accident pre- vention measures. Indica
ページ4に含まれる内容の要旨
Safety Instructions For Power Tools 9. USE PROPER EXTENSION CORD 13. DON’T OVERREACH. Keep prop- for the charger. Make sure your er footing and balance at all times. extension cord is in good condition. 14. MAINTAIN TOOLS WITH CARE. Conductor size should be in accor- Keep tools sharp and clean for dance with the chart below. The best and safest performance. amperage rating should be listed on Follow instructions for lubricating the motor or tool nameplate. An and changing accessories. undersized
ページ5に含まれる内容の要旨
CHARGING SAFETY 1. READ ALL INSTRUCTIONS and 7. IF CHARGER LIGHT FAILS TO warnings on the battery and charg- COME ON check the incoming er before charging the battery. power supply. If power source is okay, then the fuse inside the 2. CHARGE ONLY USING THE SUP- charger needs replacement. PLIED CHARGER AND BAT- Charger should be serviced by a TERY. Do not use with other batter- qualified electrical technician only. ies, chargers or drills. 8. CHARGER HAS A POLARIZED 3. DO NOT EXPOSE BATTERY OR P
ページ6に含まれる内容の要旨
BEFORE YOU START First review the contents of your cordless 4. To begin charging, press the “SET” tool kit and familiarize yourself with the key button. A steady red light over the components: word “ON” should come on indicating the battery is being charged. Heavy-Duty Case 5. When the battery is fully charged, the Cordless Drill red light will go off and the unit will Cordless Detail Sander stop charging. Remove the battery Cordless Jig Saw from the charger upon completion of Saw Blade the char
ページ7に含まれる内容の要旨
DRILL OPERATION Inserting Battery Into Drill 1. Insert the battery into the handle of the drill so that the long end is for- ward. The battery will only install in one orientation. 2. Make sure the securing clasps on either side of the drill base engage with the clips on the battery compart- ment. Inserting and Removing Bits and Drivers: Fig 1. Inserting bits into the chuck. 1. Set the direction switch, located just above the trigger, so that it is in the center position. 2. Hold the chuck by th
ページ8に含まれる内容の要旨
DRILL OPERATION, CONT’D numbers from 1 to 5 on it, and a point- Operating the drill er indicator embossed on the drill case. Set on 1 for very light applica- 1. Set the Direction Switch for the tions such as driving screws into dry- desired rotation of the bit or driver. wall. Use the higher settings up to 5 The direction switch is the sliding for denser woods and materials. Use switch located just above the trigger. the drill bit symbol when boring holes. When looking down on the drill, push- U
ページ9に含まれる内容の要旨
JIG SAW OPERATION Jig Saw Install the jig saw blade into the jig saw. The teeth of the blade should be pointed ® forward. Remove the Allen screw and metal blade retainer tab. (See Figure 3). Lay the blade in position with the larger hole of the blade over the threaded hole. ® Insert the Allen screw, with the retainer tab, through the blade and back into the ® threaded hole. Tighten the Allen screw. Refer to the Grizzly catalog or website for other types of blades suitable for a wide variety of m
ページ10に含まれる内容の要旨
DETAIL SANDER OPERATION Detail Sander Transfer the battery pack to the sander. The battery snaps into the base the same as the drill. Install the desired sandpaper grit onto the triangular sanding pad. Please consult the Grizzly catalog or website for ordering information for sandpaper. The sandpaper attaches by means of a hook and loop material. Be certain the replacement sand- paper purchased is of this type. The oscillating motion of the triangular sanding pad provides fast cutting action for
ページ11に含まれる内容の要旨
OPERATING TIPS AND MAINTENANCE Maintenance Operating Guides and Tips Avoid overloading the drill, sander or Your cordless power tool will give you hun- jig saw. Do not apply excessive dreds of hours of operation time before pressure to the tool while using. If ever needing service. The electrical com- the speed drops abnormally, ponents of this cordless drill are not user decrease pressure immediately. serviceable. Repair should always be When drilling, if the bit stops abrupt- undertaken by a q
ページ12に含まれる内容の要旨
WARRANTY AND RETURNS Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of main- tenance. This is Grizzly’s sole written warranty and any and all warranties that may be implied by law, including any merchantability or fitness, for any particular purpose, are here- by limited to
ページ13に含まれる内容の要旨
WARRANTY CARD Name__________________________________________________________ Street__________________________________________________________ City____________________State________Zip_________ Phone Number____________E-Mail___________________FAX____________ MODEL # G8594 14.4V Cordless Set Order #_______________________ The following information is given on a voluntary basis. It will be used for marketing purposes to help us develop better products and services. Of course, all information is stri
ページ14に含まれる内容の要旨
Send a Grizzly Catalog to a friend: Name________________________________ Street________________________________ City______________State______Zip_______ FOLD ALONG DOTTED LINE GRIZZLY INDUSTRIAL, INC. P.O. BOX 2069 BELLINGHAM, WA 98227-2069 TAPE ALONG EDGES--PLEASE DO NOT STAPLE G8594 14.4V Cordless Set -14-
