ページ1に含まれる内容の要旨
3 N 1
Leaf Blower Vac
91010
ASSEMBLY AND OPERATING INSTRUCTIONS
®
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our Web site at: http://www.harborfreight.com
®
Copyright 2003 by Harbor Freight Tools . All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight Tools.
For technical questions, please call 1-800-444-3353.
ページ2に含まれる内容の要旨
PRODUCT SPECIFICATIONS Injection molded polypropylene Totally enclosed fan cooled Construction Fan blower type plastic housing and tube blower white polypropelene fan 2100 Watts, 20.8 Amps Peak Motor Unit 110-120 Volts AC, 60 Hz Motor Power Power Speed Control Dial Control, settings 1 - 6 Motor Speed variable 8000 - 15,000 rpm Weight 12.5 lbs. Capacity 12 gallons Motor Housing 7-1/4"L x 5-5/16"W x 2-1/2" 17-3/4"L x 8-1/2"W x 14-1/2"H Inlet Dimensions Dimensions Diam. Sound Pressure Level 84.3 de
ページ3に含まれる内容の要旨
ELECTRICAL SAFETY 4. Grounded tools must be plugged into an outlet properly installed and grounded in accordance with all codes and ordinances. Never remove the grounding prong or modify the plug in any way. Do not use any adapter plugs. Check with a qualified electrician if you are in doubt as to whether the outlet is properly grounded. If the tool should electrically malfunction or break down, grounding provides a low resistance path to carry electricity away from the user. 5. Double insul
ページ4に含まれる内容の要旨
12. Avoid accidental starting. Be sure the Power Switch is off before plugging in. Carrying power tools with your finger on the Power Switch, or plugging in power tools with the Power Switch on, invites accidents. 13. Remove adjusting keys or wrenches before turning the power tool on. A wrench or a key that is left attached to a rotating part of the power tool may result in personal injury. 14. Do not overreach. Keep proper footing and balance at all times. Proper footing and balance enable
ページ5に含まれる内容の要旨
SERVICE 22. Tool service must be performed only by qualified repair personnel. Service or maintenance performed by unqualified personnel could result in a risk of injury. 23. When servicing a tool, use only identical replacement parts. Follow instructions in the “Inspection, Maintenance, And Cleaning” section of this manual. Use of unauthorized parts or failure to follow maintenance instructions may create a risk of electric shock or injury. SPECIFIC SAFETY RULES 1. Maintain labels and namep
ページ6に含まれる内容の要旨
10. WARNING! Never operate this tool in the rain or wet conditions. Danger of electrical shock or electrocution exists in these conditions. 11. Never lay the Vacuum Leaf Blower down until the motor has come to a complete stop. Allow the motor to come to a complete stop before releasing it, as an uncontrolled running tool may create risk of serious injury. 12. Never leave the Vacuum Leaf Blower unattended when it is plugged into an electrical outlet. Turn off the tool, and unplug it from
ページ7に含まれる内容の要旨
GROUNDING WARNING! Improperly connecting the grounding wire can result in the risk of electric shock. Check with a qualfified electrician if you are in doubt as to whether the outlet is properly grounded. Do not modify the power cord plug provided with the tool. Never remove the grounding prong from the plug. Do not use the tool if the power cord or plug is damaged. If damaged, have it repaired by a service facility before use. If the plug will not fit the outlet, have a proper outlet inst
ページ8に含まれる内容の要旨
DOUBLE INSULATED TOOLS: TOOLS WITH TWO PRONG PLUGS 4. Tools marked “Double Insulated” do not require grounding. They have a special double insulation system which satisfies OSHA requirements and complies with the applicable standards of Underwriters Laboratories, Inc., the Canadian Standard Association, and the National Electrical Code. (See Figure B.) 5. Double insulated tools may be used in either of the 120 volt outlets shown in the following illustration. (See Figure B.) This tool has a 2
ページ9に含まれる内容の要旨
6. If you are using an extension cord outdoors, make sure it is marked with the suffix “W-A” (“W” in Canada) to indicate it is acceptable for outdoor use. 7. Make sure your extension cord is properly wired and in good electrical condition. Always replace a damaged extension cord or have it repaired by a qualified electrician before using it. 8. Protect your extension cords from sharp objects, excessive heat, and damp or wet areas. RECOMMENDED MINIMUM WIRE GAUGE FOR EXTENSION CORDS* (120 VOLT) N
ページ10に含まれる内容の要旨
ASSEMBLY AND OPERATING INSTRUCTIONS CAUTION: Always make sure the Power Cord is unplugged from its electrical outlet prior to assembling or making any adjustments to the tool. Attaching and removing the Blower Tube Assembly: (Please see assembly diagram on next page) 1. Insert the guiding end of the Blower Extension into the Upper Tube. Push the two sections together firmly until the clip engages. These two pieces together form the Blower Tube Assembly. 2. Insert the Blower Tube Assembly firmly
ページ11に含まれる内容の要旨
Fastener Motor Housing Upper Blower Tube Blower Assembly Function Selector Blower Extension Mulch Bag Attaching and removing the Mulch Bag: 1. Position the Mulch Bag at the underside of the unit, with the pointed end of the bag toward the open end of the blower tube. Loop the opening in the Mulch Bag over the opening at the bottom of the Motor Housing. Tighten the cord on the bag around the edge of the opening on the Motor Housing. 2. Attach the hook on the Mulch Bag to the Upper Blower Tube. Bl
ページ12に含まれる内容の要旨
Turning the unit ON and OFF, and Adjusting Blower Speed WARNING! Do not turn this unit on unless you are wearing safety glasses, and have taken precau- tions to be sure it is safe to do so. 1. To turn on unit, be sure it is plugged in. Then move ON/OFF Switch to the “|” position. To turn unit OFF, rotate switch to “O” position. Speed Control ON / OFF Switch 2. To adjust blower speed, rotate the Speed Control to any of its 6 posi- WARNING! Never direct blown air toward tions. any person or animal
ページ13に含まれる内容の要旨
PARTS LIST Pn art NumberDr escriptio Pn art Numbe Descriptio 1 Left Motor Housing / Handle 16 Press-on Fastener 2 Left Upper and Lower Blower Tubes 17 Power Connector 3 Right Motor Housing / Handle 18 ON / OFF Switch 4 Right Upper and Lower Blower Tubes 19 Assistance Switch 5 Function Selector 20 Motor Rear Assembly 6 Screw 21 Motor 7 Pin 22 Motor Front Assembly 8 Tube Connector 23 Fan 9 Capacitor 24 Guide Wheel 10 Screw 25 Wheel Axle 11 26 Safety Switch Lead Wind Pipe 12 27 Press Board Fixture
ページ14に含まれる内容の要旨
ASSEMBLY DIAGRAM #30 and #31 listed on Parts List, not shown on Assembly Diagram. NOTE: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. SKU 91010 Page 14 REV 11/04
