ページ1に含まれる内容の要旨
arbor press
03551
Model
03552
set up and operating instructions
Visit our website at: http://www.harborfreight.com
read this material before using this product.
Failure to do so can result in serious injury.
sa Ve this Manual.
© ®
Copyright 1997 by Harbor Freight Tools . All rights reserved. No portion of this manual or any artwork
contained herein may be reproduced in any shape or form without the express written consent of
Harbor Freight Tools. Diagrams within this manual may not be d
ページ2に含まれる内容の要旨
not let them handle machines, tools, or speciFications extension cords. 3551 3552 4. store idle eQuipMent . When not Capacity 1/2 Ton 1 Ton Maximum Height 4-1/2” 5-1/2” in use, tools must be locked up in a dry Maximum Diameter 6-1/2” 8” location to inhibit rust. Always lock up Largest Arbor 1” 1-1/8” tools and keep out of reach of children. Ram Square 3/4” 1” Height of Press 10” 13” 5. do not Force the tool. It will do Base Dimensions 4” x 9-1/2” 5” x 11” the job better and more safely at t
ページ3に含まれる内容の要旨
11. Maintain tools With care. Keep damaged should be properly repaired tools sharp and clean for better and or replaced by a qualified technician. Do safer performance. Follow instructions not use the tool if any switch does not for lubricating and changing accessories. turn on and off properly. Inspect tool cords periodically and, if 18. guard against electric shocK. damaged, have them repaired by an Prevent body contact with grounded authorized technician. The handles must surfaces suc
ページ4に含まれる内容の要旨
arbor press assembly asseMbly Mounting the body to your Plate (#6) Workbench Spring Pin (#7) 1. Select a place on your workbench to (not shown) mount the Arbor Press. Body (#1) 2. Purchase hardware to mount your Arbor Press to your workbench. Bolt length will be the thickness of your workbench plus 2-1/2” of length for the Arbor Press BODY (#1). Figure 2 -- Installing the Plate Body (#1) 1. Place the PLATE (#6) onto the Base of Mounting Hole (not shown) the BODY (#1) as shown in Figu
ページ5に含まれる内容の要旨
3. Unwrap the Handle Assembly and discard 7. Your Arbor Press is ready for use. the protective padding. Handle Assembly Body (#1) Figure 4 -- Installing the Handle Assembly 4. Insert the GEAR (#14) section of the Handle Assembly into the side of the Arbor Press as shown in Figure 4. The GEAR will only fit into the side shown in the Figure. 5. You may have to rotate the Handle Assembly slightly to get the teeth of the GEAR to mesh with the teeth of the RACK. Rack (#10) Ring (#5) Handle As
ページ6に含まれる内容の要旨
using the arbor press operation adjusting the handle assembly 1. Determine if you will need a moderate or Rack (#10) large amount of leverage for the job. Lock Pin (#11) Shaft (#15) Shaft (#15) Plate (#6) Figure 7 -- Raising the Rack Figure 6 -- Adjusting the Shaft 1. Raise the RACK (#10) up by turning the Handle Assembly as shown in Figure 7. 2. Loosen the LOCK PIN (#11) by turning it as shown in Figure 6. This will allow you 2. Turn the PLATE (#6) until the appropriate to adjust the
ページ7に含まれる内容の要旨
parts list and asseMbly diagraM part description Qty part description Qty part description Qty 1 Body 1 7 Spring Pin 1 13 Screw 1 2 Bolt 8 8 Cover 1 14 Gear 1 3 Nut 6 9 Washer 1 15 Shaft 1 4 Screw 1 10 Rack 1 16 Handle 2 5 Ring 1 11 Lock Pin 1 6 Plate 1 12 Pin 1 SKU 03551 03552 For technical questions, please call 1-800-444-3353. Page 7
ページ8に含まれる内容の要旨
liMited 90 day Warranty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper installatio
