ページ1に含まれる内容の要旨
INSTRUCTION MANUAL
… with Replacement Parts
MODELS
FD3-150, FD3-200 & FD3-300
FOOD WASTE DISPOSERS
ML-110301 FD3-150
ML-110305 FD3-200
ML-110309 FD3-300
A product of HOBART CORPORATION 701 RIDGE AVENUE TROY, OHIO 45374-0001
FORM 19307 Rev. B (9-97)
ページ2に含まれる内容の要旨
37 36 38 1 33-34-35 39 2 32 31 3 30 4 29 28 27 26 5 25 6 8 7 24 23 22 9 11 21 20 19 18 10 12-13 14 THUR 17 PL-22349-1 DISPOSER UNIT – 2 –
ページ3に含まれる内容の要旨
DISPOSER UNIT ILLUS. PART PL-22349-1 NO. NAME OF PART AMT. 1 3 1 SC-118-16 Cap Screw ⁄4-20 x 1 ⁄8 Hex Hd. ..................................................................................................10 2 00-203185 Ring - Top Cone Clamp (Half) ......................................................................................................2 3 00-202105 Guard - Splash .........................................................................................................................
ページ4に含まれる内容の要旨
Installation, Operation, and Care of MODELS FD3-150, FD3-200, & FD3-300 FOOD WASTE DISPOSERS SAVE THESE INSTRUCTIONS GENERAL The disposer features removable hardened steel components and reversible rotation with grinding in both directions. The disposer is self-feeding, making it unnecessary to force the food waste into the grinding mechanism. The FD3 Series disposers utilize hardened steel cutter blocks (1, Fig. 1) mounted to a rotating flywheel (4, Fig. 1) and a stationary shredder ring (2 F
ページ5に含まれる内容の要旨
For an accessory group D installation, use the mounting flange (1, Fig. 3) included with accessory group D. See Fig. 3 and the accessory group data sheet. Fig. 2 Fig. 3 WARNING: HAZARDOUS MOVING PARTS — DO NOT OPERATE DISPOSER UNTIL PROPERLY INSTALLED Countertop Work Surface TO CONE. 6" Minimum Use one of the following: Part No. 204006 or 204007 Custom Built, Locally Supplied (15 inch diameter cone) or Part No. 204003 or 204004 Cone (18 inch diameter cone). For custom-built installations — mi
ページ6に含まれる内容の要旨
Water Connections 3 Connect disposer (1, Fig. 5) from a /4" IPS cold water supply line. Install the eight gallon per minute flow control supplied with the disposer (2, Fig. 5). If the water line pressure exceeds 60 psig, a pressure reducing valve (6, Fig. 5) (not supplied) should be installed. The minimum flow pressure for the disposer to function properly is 16 psig. Install a shut-off valve (not supplied) for proper servicing of the disposer. All control groups are supplied with a solenoid
ページ7に含まれる内容の要旨
OPERATION Before operating disposer make sure it is clear of foreign objects such as metal or wire clippings, screws, nails, etc., which may have dropped into it during installation. Check the flywheel for free rotation. WARNING: NEVER USE YOUR HAND TO CHECK ROTATION OF FLYWHEEL OR TO REMOVE FOREIGN MATTER FROM THE DISPOSER. USE A STICK OR SIMILAR OBJECT TO TURN THE FLYWHEEL. FOREIGN MATTER CAN BE REMOVED WITH TONGS OR PLIERS. Start the disposer before feeding food waste. Be sure water is f
ページ8に含まれる内容の要旨
CLEANING The food waste disposer should be kept in a clean and sanitary condition. Allow the disposer to run a few minutes after disposing of all food waste to completely flush out the interior. If food waste is allowed to accumulate due to improper clean-up, it will give off offensive odors. If this happens, cleaning can be accomplished by using a stiff brush with a strong soap and hot water solution. Light cleaning can be accomplished by grinding ice and a lemon through the disposer. CAUTIO
