ページ1に含まれる内容の要旨
Product features may vary from the picture above.
Please read this manual and save it with your original sales receipt.
Tools needed for assembly: Phillips Screwdriver, Hammer, Pliers
and Safety Scissors (tools not included).
® ®
Use only with a Power Wheels 12 Volt Lead-Acid Rechargeable Battery and Power Wheels
12 Volt Charger with Type “12V” Connector (included).
JEEP and the Jeep grille design are registered trademarks of DaimlerChrysler
Corporation and are used under license. ©DaimlerChrys
ページ2に含まれる内容の要旨
Table of Contents A Important Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 B Warnings and Cautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 C Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ページ3に含まれる内容の要旨
Warnings and Cautions B ELECTRICAL HAZARD WARNING • Battery can fall out and injure a child if vehicle tips over. Always use battery clamp. • PREVENT FIRE - Never modify the electrical system. Alterations could cause a fire resulting in serious injury and could also ruin the electrical system. - Use of the wrong type battery or charger could cause a fire or explosion resulting in serious injury. ® ® - Use of Power Wheels components in products other than Power Wheels vehicles could cause over
ページ4に含まれる内容の要旨
Parts C • If you experience a problem with this product, or are missing a part, please call us at 1-800-348-0751, rather than return this product to the store. • Please identify all parts before assembly and save all packaging material until assembly is complete to ensure that no parts are discarded. •Metal parts have been coated with a lubricant to protect them during shipment. Wipe all metal parts with a paper towel to remove any excess lubricant. Spacer - 2 12 Volt Battery Brushguard Light Co
ページ5に含まれる内容の要旨
Parts #8 x 4" Screw – 2 Key Assembly 1 #10 x 1" Screw – 7 #8 x 1" Screw – 7 #10 x /2" Screw – 8 #8-32 x 1.625" Screw – 2 #8 Lock Nut – 2 Hood Latch – 2 .354 Cap Nut – 2 All Shown Actual Size 1 " " *For your convenience, an extra .354 cap nut, #8 x 1", #10 x / 2 and #10 x1 fasteners are included. Steering Column Sport Bar Support - 2 Vehicle Body Dash Seat Windshield Steering Wheel Hood Sport Bar Not Shown: Label Sheet 5
ページ6に含まれる内容の要旨
Parts Diagram D 29 14 16 19 30 10 27 3 28 18 21 31 22 10 22 7 12 25 13 14 13 10 20 11 10 23 6 24 4 13 8 5 9 26 15 1 13 14 17 15 13 2 3 Note: Some parts shown are assembled on both sides of the vehicle. No. Part Quantity No. Part Quantity No. Part Quantity 1Vehicle Body 1 13 #10 x 1" Screw 7 25 Hood 1 1 2Steering Column 1 14 #10 x / 2" Screw 8 26 Spacer 2 3 .354 Cap Nut 2 15 #8 x 4" Screw 2 27 Sport Bar 1 4 Hood Latch 216Windshield 1 28 Sport Bar Support 2 5 12 Volt Battery 1 17 Brushguard 1 29 L
ページ7に含まれる内容の要旨
Battery Charging E About Thermal Fuses ELECTRICAL HAZARD ® Your Power Wheels 12 volt battery is equipped with a built-in thermal fuse. The thermal fuse is a self-resetting WARNING safety device which automatically “trips” and shuts down operation of the vehicle if the vehicle is overloaded or the driving conditions too severe. Once a fuse has “tripped”, • Battery can fall out and injure a it will automatically reset itself after approximately child if vehicle tips over. Always use 25 seconds
ページ8に含まれる内容の要旨
Battery Charging Assembly F WARNING Battery Children can be harmed by small parts, sharp edges and sharp points in the vehicle’s unassembled state, or by electrical items. Care should be taken in unpacking and assembly of the vehicle. Children should not handle parts, including the battery, or help in assembly of the vehicle. Charger Connector IMPORTANT! The battery clamp unit must be assembled to the dash before assembling the dash to the vehicle body. • Plug the charger connector into the ba
ページ9に含まれる内容の要旨
Assembly 13 15 2 4 14 Battery Clamp Unit 12 17 HI LO KC 21 23 16 Labels - Dash • Before applying the labels, wipe the surface of the •Insert two #10 x 1" screws through the holes in the vehicle with a clean, dry cloth to remove any dust or oils. battery clamp unit and into the pegs in the dash. • Place the labels exactly as shown in the illustrations. • Tighten the screws with a Phillips screwdriver. Do not over-tighten. •For best results, avoid repositioning a label once it has been applied to
ページ10に含まれる内容の要旨
Assembly End of Dash Key Assembly 5 7 Steering Column Steering Rod Cap Nut .354" Dash View Bottom View .354 Cap Nut •Insert and “snap” the key assembly into the opening in •Insert the end of the steering column through the hole the dash, as shown. in the steering rod. • Fit a cap nut onto the end of the steering column. • While supporting the steering column, tap the cap nut 6 with a hammer to secure it on the steering column. Hint: You may want the help of another person to support the steering
ページ11に含まれる内容の要旨
Assembly Steering Wheel 8 Wide Tab 10 Tab Steering Column Lens Cap Nut Wide Notch Lens Guard “UP” • Fit the wide notch in the side of a headlight lens under .354" the wide tab on a lens guard. • Press firmly on the inside of the headlight lens to snap it into the lens guard. .354 Cap Nut • Repeat this procedure to assemble the other headlight lens to the remaining lens guard. •Turn the vehicle upright. •Position the steering wheel so that the spokes form a “Y” as shown. The tab on the steering
ページ12に含まれる内容の要旨
Assembly Windshield 12 14 Hood Latch Wipers Slot Large Tab Large Tab Large Slots Hood Latch Slot •Position the windshield so that the wipers face the front •Insert a hood latch into one of the slots in the vehicle end of the vehicle. body, near the hood area. •Insert and “snap” the two large tabs on the windshield 1 •Twist the base of the hood latch /4 turn to secure it in into the large slots in the dash. the vehicle body. • Pull up on the windshield to be sure it is secure. • Repeat this proce
ページ13に含まれる内容の要旨
Assembly Spacers 16 18 Long Seat Belt Strap T-Loop Fastener End Grille •Insert each fastener end of the long seat belt strap through a slot in the center of the seat. Make sure the fasteners face the outer edge of the seat. • Pull each side of the long seat belt strap evenly through Brush Guard the slots. Make sure to pull each T-loop through a slot. •Turn the seat upright. • Fit two spacers between the grille and the back of the brush guard, as shown. 19 •Insert two #8 x 4" screws through the b
ページ14に含まれる内容の要旨
Assembly Lights 22 20 Light Covers Dash View •Insert a #8 x 1" screw into the rear of seat, as shown. • Tighten the screw with a Phillips screwdriver. Do not over-tighten. • Fit the light covers to the lights on the sport bar, as shown. 1 " • Insert a #10 x /2 screw through the light cover and into the light. Tighten the screws with a Phillips screwdriver. 21 Do not over-tighten. Sport Bar Supports • Fit a support to one side of the sport bar. " • Insert a #8- 32 x 1.625 screw through the supp
ページ15に含まれる内容の要旨
Assembly 23 25 Taillight Housing Sport Bar Support PUSH HERE Side Taillight Fender Lens #8 x 1" Screws •Turn the vehicle upright. PULL HERE • Using safety scissors, remove the taillight lenses and the taillight housings from the plastic connectors. Dispose of the plastic connectors. •Face the rear of the vehicle. • Fit a taillight lens inside a taillight housing. •Fit the sport bar into the holes in the vehicle body. •Position the taillight housing with lens against the vehicle • Push down firm
ページ16に含まれる内容の要旨
Label Decoration G Proper label application will help to keep the labels looking their best! When applying labels, keep the following guidelines in mind: •Wash your hands before applying the labels. • Before applying the labels, wipe the surface of the vehicle with a clean, dry cloth to remove any dust or oils. • Place the labels exactly as shown in the illustrations. •For best results, avoid repositioning a label once it has been applied to the vehicle. • After applying a label, rub the label f
ページ17に含まれる内容の要旨
Label Decoration 3 3 11 1 7 10 29 30 29 27 30 4 Right Side View 25 4 24 6 11 29 30 2 27 29 30 5 Left Side View 17
ページ18に含まれる内容の要旨
Pb Pb Pb Battery Installation H Battery 3 ® IMPORTANT! Use only a Power Wheels 12 volt battery. Battery Battery Clamp Use of any other battery will damage your vehicle. Make Compartment sure that you charge the battery for at least 18 hours using ® the enclosed Power Wheels 12 volt charger before operating your vehicle for the first time. Charge the battery for at least 14 hours after each use of the vehicle. Never charge the battery longer than 30 hours. Failure to follow these instructions ma
ページ19に含まれる内容の要旨
Battery Care and Disposal I Care Disposal ® If a battery leak develops, avoid contact with the leaking •Your Power Wheels battery is a sealed lead-acid acid and place the damaged battery in a plastic bag. Please battery. It must be recycled or disposed of in an refer to the information on this page for proper disposal. environmentally sound manner. If acid comes in contact with skin or eyes, flush with cool • Do not dispose of a lead-acid battery in your regular, water for at least 15 minutes a
ページ20に含まれる内容の要旨
Rules for Safe Driving J RIDING HAZARD WARNING Prevent Injuries and Deaths • Direct Adult Supervision Required. •Keep Children Within Safe Riding Areas Use vehicle on generally level ground ONLY! These areas must be: - away from swimming pools and other 7. Do not allow your child to drive on sloped or inclined bodies of water to prevent drownings. surfaces. Restrict your child’s driving to generally level - generally level to prevent tipovers. ground ONLY! 8. Do not allow your child to drive dow
