ページ1に含まれる内容の要旨
JCR-263
AM/FM DUAL ALARM CLOCK RADIO
INSTRUCTION MANUAL
PLEASE READ THIS OPERATING MANUAL COMPLETELY BEFORE OPERATING
THIS UNIT AND RETAIN THIS BOOKLET FOR FUTURE REFERENCE.
ページ2に含まれる内容の要旨
SAFETY INSTRUCTIONS WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. 1. Read these instructions 2. Keep these instructions 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with these instructions. 8. Do not install near any heat sources such as radiators, heat registers,
ページ3に含まれる内容の要旨
PROTECT YOUR FURNITURE!! This system is equipped with non-skid rubber ‘feet’ to prevent the product from moving when you operate the controls. These ‘feet’ are made from non-migrating rubber material specially formulated to avoid leaving any marks or stains on your furniture. However certain types of oil based furniture polishes, wood preservatives, or cleaning sprays may cause the rubber ‘feet’ to soften, and leave marks or a rubber residue on the furniture. To prevent any damage to your
ページ4に含まれる内容の要旨
POWER SOURCE This AM/FM Dual Alarm Clock Radio operates on AC 240V~ 50Hz line power supply. 2 ‘AA’ (UM-3) alkaline batteries (Not included) are also required to retain the normal and alarm time settings in the event of a power outage. AC OPERATION Plug the AC Power Cord into the AC 240V~ 50Hz power source. BACKUP BATTERY INSTALLATION 1. Open the Battery Compartment Door. Following the polarity diagram shown in the Battery Compartment, insert 2 new ‘AA’ size (UM-3) alkaline batter
ページ5に含まれる内容の要旨
TIME SETTING NOTE: The clock has to be set when you first plug it in. The following procedure illustrates the setting of the Clock using 7:30 PM as an example time. 1. Connect the AC cord to an AC 240V~ 50 Hz power outlet. The LCD will show “AM 12 : 00” Note: Make sure to use an outlet that is always “live”. Do not use an outlet that is controlled by a wall switch. 2. For best viewing, press the BRIGHTNESS Button (# 14) once to turn on the LCD back-light. Press the BRIGHTNESS B
ページ6に含まれる内容の要旨
II. This receiver has a built-in bar antenna. If the AM reception is week, slightly rotate or re-positioning the unit will usually improve the reception. AUX OPERATION THIS UNIT FEATURES AN AUX LINE-IN JACK FOR CONNECTING YOUR iPod, MP3 PLAYER OR OTHER DIGITAL MUSIC PLAYER. 1. Connect the headphone jack of your external device to the AUX IN Jack (# 8) located on the back of the JＣＲ－２６３ (cable not included). 2. Turn on the JＣＲ－２６３ and set the FUNCTION Selector (# 9) to the
ページ7に含まれる内容の要旨
６． When the preset wake up time is reached the selected wakeup mode turns “On”. The respective ALARM Indicator（ＡＬ１ ｏｒ ＡＬ２）ａｎｄ Wakeup mode ｉｃｏｎ（ ｏｒ ）will flash. The alarm will continue to sound and last for ３0 minutes before turning off automatically. The alarm remains set and will turn the JＣＲ－２６３ on again at the same time on the following day. ７． To stop the alarm before the alarm time elapses, press the ＡＬＡＲＭ ＯＦＦ Button (# 14). The alarm will st
ページ8に含まれる内容の要旨
３． The JCR-263 will turn on when the preset NAP time has elapsed. ４． To cancel the NAP time before it turns the JCR-263 on, press the NAP Button once. When the NAP time appears press the NAP Button again. The NAP time will resume to current time display. Press the NAP Button the third time and hold until “NAP” disappears in the LCD. SLEEP OPERATION You can use the SLEEP Timer to fall asleep to Radio for a maximum duration of 120 mi
ページ9に含まれる内容の要旨
IMPORTANT: Remember that the station and volume settings you choose for the SLEEP TO MUSIC operation are the same settings you will hear if you set the alarm for wake to radio the following morning. REPLACING TOP AND FRONT LENS There are four interchangeable top and front lens’ in assorted colors included that can be used in place of the panels that come pre-installed. Follow the steps below to replace the lens’. 1. Insert the provided tool between the cabinet and the
ページ10に含まれる内容の要旨
SERVICE All necessary care is taken at the point of manufacture to ensure this unit will perform to the Jensen’s high quality standards. However if this unit becomes faulty within the warranty period please return it to the point of purchase with your proof of purchase for a replacement. When returning the unit, please remove any batteries to prevent damage to the unit in transit and/or from possible battery leakage. Please note that we are not responsible for batteries returned with
