ページ1に含まれる内容の要旨
®
LITTLE WONDER
PARTS LIST, OPERATING AND
ASSEMBLY INSTRUCTIONS FOR
PRO HONDA EDGER, MODEL #6232
®
©2001, LITTLE WONDER , Division Schiller-Pfeiffer, Inc.
ページ2に含まれる内容の要旨
6. DON’T OVERREACH OR STAND ON IMPORTANT SAFETY INSTRUCTIONS UNSTABLE SUPPORT - Keep good footing and balance at all times. To avoid injury when using WARNING ! ! your Honda Edger, follow 7. NEVER DIRECT DIS- DANGER ! ! basic precautions, including the following: CHARGE OF MATERI- AL TOWARD BYSTANDERS OR ALLOW ANY- 1. READ THESE IMPORTANT SAFETY ONE NEAR THE AREA OF OPERATION. Use INSTRUCTIONS, THE OPERATING INSTRUC- care in directing discharge to avoid glass enclosures, TIONS, ASSEMBLY
ページ3に含まれる内容の要旨
15. STORE MACHINE INDOORS - When not in 24. STOP THE ENGINE WHEN LEAVING THE use, store indoors in a dry place, locked or otherwise MACHINE UNATTENDED. inaccessible to children. 25. WHEN CLEANING, REPAIRING, OR 16. DO NOT ATTEMPT TO REPAIR MACHINE INSPECTING, make certain the blade and all mov- - Have repairs made by qualified dealer or repairman. ing parts have stopped. Disconnect the spark plug Use only original Little Wonder replacement parts. wire, and keep the wire away from the plug so tha
ページ4に含まれる内容の要旨
SAFETY DECAL IDENTIFICATION Key #87 P/N 210 Key #84 P/N 4036 Key #85 P/N 211 Key #86 P/N 260 6232 4
ページ5に含まれる内容の要旨
6 4 0 4 4 - 0 2 1 3 / 4 .10 4 1 6 3 5 7 2 .10 .17 6 1 2 6 6 . 1 0 H a n d l e - S u p p o r t L H 1 .10 .17 .10 .10 8 2 6 7 . 1 0 H a n d l e - S u p p o r t , R H .10 6 4 1 4 1 - 2
ページ6に含まれる内容の要旨
ページ7に含まれる内容の要旨
6 1 4 1
ページ8に含まれる内容の要旨
6. Insert the end of the throttle cable into the hole on THROTTLE INSTALLATION the engine throttle lever. INSTRUCTIONS 7. Place the cable-retaining clamp over the cable, insert the screw and tighten. 1. Remove the air filter cover from the engine. 8. Replace the air filter cover. 2. Use a 10mm socket to loosen the throttle lever pivot nut. 9. The remote throttle lever should move from slow to fast and be approximately centered in its slot. 3. Move the remote throttle lever so that the center of
ページ9に含まれる内容の要旨
ment, inspection or the like. OPERATING INSTRUCTIONS 4. Operate machine from position where guards block the line of sight to the cutting member. A. BEFORE STARTING E. OPERATING 1. Place Edger on level surface; be sure blade is not obstructed and the area is clear and free of 1. Eye protection must be worn at all times. Use bystanders. Your Edger is equipped with a Honda common sense and exercise caution at all times when 4-cycle engine. operating your Edger. 2. Check oil level, and be sure cr
ページ10に含まれる内容の要旨
vered "wheelbarrow fashion." WARNING: The engine on your Pro Honda Edger is not equipped with a spark arrester and USER MAINTENANCE if machine is to be used on any forest-covered, brush-covered, or grass-covered unimproved INSTRUCTIONS land, before using on such land a spark arrester must be added to the muffler. The arrester must 1. Keep all nuts, bolts and screws tight. be maintained in effective working order by the operator. In the State of California, the above is 2. Never store the machine
ページ11に含まれる内容の要旨
TROUBLESHOOTING GUIDE PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION A. Engine will not start 1. Out of gasoline. 1. Fill gasoline tank. 2. Spark plug lead wire loose 2. Reconnect spark plug lead wire. or disconnected. 3. Defective spark plug. 3. Replace spark plug. 4. Throttle control lever not 4. Move throttle control lever to start position. in proper position. 5. Engine flooded or flooding. 5. Start engine with choke fully open. 6. Stale or contaminated 6 Drain, clean tank and system and refill wi
ページ12に含まれる内容の要旨
7 0 1 2 / 4 1 6 3 2 4 0 s i .
