ページ1に含まれる内容の要旨
© 2011 Pella Corporation
Part Number: 818L0100
INSTALLATION INSTRUCTION -
INSTRUCCIONES DE INSTALACION
CLAD HINGED PATIO DOOR — (INCLUDES STANDARD,
®
PERFORMANCE UPGRADE AND HURRICANESHIELD
IMPACT RESISTANT IN-SWING AND OUT-SWING)
Important Safety Information:
Pella® HurricaneShield Products have been tested in accordance with the large missile impact testing
requirements and have been certified to meet those requirements. Check with the individual (building
owner, architect, contractor
ページ2に含まれる内容の要旨
Interior Interior SEAL SEAL ANT ANT The performance of any building is dependent upon the design, installation, and workmanship of the entire building system. Pella Corporation strongly recommends consulting an experienced architect, contractor or structural engineer prior to installation of Pella products. The individual (building owner, architect, contractor, installer and/or consumer) responsible for the project must take into account local conditions, building codes, inherent component
ページ3に含まれる内容の要旨
1" 6" Exterior Water Resistive Barrier C. c ut the water resistive barrier. 1st cut 3rd cut 4th cut: Make a 6" cut up from o each top corner at a 45 angle to allow the water resistive barrier to be lapped over the fin at the head of the door. 1C 2nd cut D. Fold the water resistive barrier. Fold side flaps into the opening and staple to inside wall. Fold top flap up and temporarily fasten with flashing tape. 1D For DoorS USIng optIonaL SILL pan go t o Step 1I. E. a pply sill flashing tap
ページ4に含まれる内容の要旨
Install flush against exterior rough opening. Weather Barrier Side Flange EXTERIOR SILL PAN LIP EXTERIOR SILL PAN LIP Flashing Tape EXTERIOR SILL PAN LIP 9" Flashing Tape EXTERIOR SILL PAN LIP Flashing Tape 1" 1" 1" Variable 1" 1" Exterior EXTERIOR SILL PAN LIP EXTERIOR SILL PAN LIP EXTERIOR SILL PAN LIP INTERIOR SILL PAN LIP INTERIOR SILL PAN LIP INTERIOR SILL PAN LIP o ptional Sill pan Instructions: I. c ut the sill pan to the width of the rough opening plus 2”. Note: The 2
ページ5に含まれる内容の要旨
EXTERIOR SILL PAN LIP EXTERIOR SILL PAN LIP INTERIOR SILL PAN LIP INTERIOR SILL PAN LIP 1" R. c ut a piece of flashing tape to the width of the opening. Install to the flanges of the sill pan and overlap the tape from step 1N by 1”. If needed add a second or third piece of flashing tape until the sill pan is covered to the interior sill pan lip. Note: The purpose of this tape is to seal the sill screws when installing the door. S. c ut two pieces of flashing tape 1-1/2” x 6” and apply to
ページ6に含まれる内容の要旨
EXTERIOR SILL PAN LIP INTERIOR SILL PAN LIP 1st Bead 2nd Bead Leave a 2" break in center of pan 3rd Bead a pplications for performance Upgrade and HurricaneShield: DOUBLE OPERABLE SINGLE FIXED OR OPERABLE Out-Swing Vent and Fixed Out-Swing Vent or Fixed 2C 2C Screw Location 6" 6" 16" MAX 16" MAX 16" MAX 6" 6" 6" 6" O.C. O.C. O.C. 6" 6" 6" 6" In-Swing Vent Out-Swing Vent or Fixed 2C 2C 2C 2C DIAGRAM FOR PLACEMENT OF THRESHOLD SCREWS & 16" 16" 16" 16" MAX. MAX. MAX. M
ページ7に含まれる内容の要旨
1 INCHES 2 3 mm 2 0 3 0 4 0 5 0 6 0 7 0 Exterior Exterior Interior TWO OR MORE PEOPLE WILL BE REQUIRED FOR THE FOLLOWINg STEPS : B. c ut and remove the strap that runs from the door lock to the sill of the door. 3C C. Insert the door from the exterior of the building. DO NOT slide the bottom of the door into the opening. Sliding will damage the sealant lines. Place the bottom of the door at the bottom of the opening, then tilt the top into position. Center the door between the sides
ページ8に含まれる内容の要旨
Interior Exterior F. Fasten the door to opening by driving 2” galvanized roofing nails into each pre-punched hole in the nailing fin. 3F Note: Make sure the fin corner is lying as flat as possible. G. c arefully open the door(s) and remove all 3H shipping spacers. Note: Be sure to remove the spacers from the bottom edge of the door panel. Double doors with center latch: Designer Series o nly: Use the construction handle to operate the active door handle. Operate the flushbolts per
ページ9に含まれる内容の要旨
Interior Interior K. Shim between the frame and the rough opening at the head strike location and at every frame anchor hole location. Remove and replace head strike screws with three #8 x 3” corrosion resistant screws (provided) through the head strike, 3K door frame, shims and into the rough opening. Note: For doors with no head strike check head for pre- drilled installation holes. If installation holes are present 3J drill 1/8" pilot in each installation hole and install a #8 x 3" s
ページ10に含まれる内容の要旨
1" Exterior Exterior Exterior INTEgRATINg THE DOOR TO THE 4 w ATER RESISTIVE BARRIER Note: The flashing tape must be applied approximately 1/2" onto the frame cladding at the jambs and head. Pre-folding the tape at 1/2" before removing the paper backing will make it easier to apply the tape correctly. If the siding is less than 1/2" thick, adjust the dimension of the fold so the exterior sealant line will cover the exterior edge of the tape. A. a pply side flashing tape. Cut two pieces of
ページ11に含まれる内容の要旨
INTEgRATINg THE DOOR TO THE INSTALL THE f ASTENERS fOR PERfORmANCE 4 w ATER RESISTIVE BARRIER 5 UPgRADE OR HURRICANESHIELD PRODUCT Frame Screw method: In-Swing Note: If installing with installation clips, 6" 16" MAX O.C. 6" 6" 16" MAX O.C. 6" 5A proceed to Step E. A. Jambs: Clearance Clearance o ut-swing: On the room side of the jamb; Hole Hole Location Location drill and counter-sink 13/64” deep diameter clearance holes through the door frame only and not into the rough opening in the
ページ12に含まれる内容の要旨
Out-Swing D. Secure the jambs and head of the door. EXTERIOR EXTERIOR Drive #10 x 3-1/2” corrosion resistant wood screws through the door frame and shim, into the rough framing. Drive the screws until snug but DO NOT over- tighten the screws. DO NOT bend or 5C Drill 1/8” diameter pilot bow the unit frame. holes through the clearance hole in the frame. 5D INTERIOR INTERIOR #10 x 3-1/2" corrosion resistant wood screw E. Drill 13/64” clearance holes through the threshold but not into the roug
ページ13に含まれる内容の要旨
6" Interior 6 INTERIOR SEAL c aution: Ensure use of low pressure polyurethane window and door insulating foams and strictly follow the foam manufacturer’s recommendations for application. Use of high pressure foams or improper application of the foam may cause the door frame to bow and hinder operation. A. a pply insulating foam sealant. From the interior, insert the nozzle of the applicator into the space between the door and the rough opening approximately 1” past the edge of the frame
ページ14に含まれる内容の要旨
SEALINg THE DOOR TO THE EXTERIOR w ALL CLADDINg 7 When applying siding, brick veneer or other exterior finish material, leave adequate space between the door frame and the material for sealant. Refer to the illustration that corresponds to your finish material. Note: The sealant details shown are standard recommendations from the sealant industry. c ontact your sealant supplier for recommendations and instructions for these and any other applications. VINYL/STEEL BRICK Backer Rod VENE
ページ15に含まれる内容の要旨
INTERIOR fINISHINg If products cannot be finished immediately, cover with clear plastic to protect from dirt, damage and moisture. Remove any construction residue before finishing. Sand all wood surfaces lightly with 180 grit or finer sandpaper. DO NOT use steel wool. BE CAREFUL NOT TO SCRATCH THE GLASS. Remove sanding dust. Pella products must be finished per the below instructions; failure to follow these instructions voids the Limited Warranty. • On casement and awnings, it is optional to
ページ16に含まれる内容の要旨
TROUBLESHOOTINg - Adjustable Strike Latching Issues Issue 1: Issue 2: Door is difficult Door needs to close to latch. Remove more tightly against the strike and the weather-strip. adjustable strike Remove the strike shim then reinstall and adjustable the strike. strike shim. Remove the tabs from the adjustable strike shim and install so that the thicker side is visible at the strike edge. Reinstall the strike. Adj. Strike Shim (end view) Factory Side to be installed used in sid
