ページ1に含まれる内容の要旨
PSZ2600
848A5393A2 (806)
G G
B B
OWNER’S MANUAL
POLE SAW
PSZ2600
GB-1
ページ2に含まれる内容の要旨
PSZ2600 EC DECLARATION OF CONFORMITY Husqvarna Zenoah Co., Ltd. We, 1-9, Minamidai, Kawagoe, Saitama, Japan declare in sole responsibility that the following products referred to in this declaration conform with DIRECTIVE 89/336/EEC, 98/37/EC, prEN11806 : 1996 The products referred to are : DESIGNATION : POLE SAW MODELS : PSZ2600 SERIAL NUMBERS : 700101 and up The company named above will keep on file the following technical documentation for any inspection purpose. • Operation instructions • P
ページ3に含まれる内容の要旨
PSZ2600 SAFETY FIRST Contents Instructions contained in warnings within this manual marked with a symbol concern critical points which must be taken 1. Parts location .................................................. 3 into consideration to prevent possible serious bodily injury, and for this reason you are requested to read all such instructions 2. Specifications ................................................. 4 G carefully and follow them without fail. 3. Warning labels on the machine ...
ページ4に含まれる内容の要旨
PSZ2600 2. Specification PSZ2600 Cutting head Overall size (L x W x H)................ 2085 x 250 x 310mm Guide bar Type.............. OREGON DOUBLE GUARD Dry weight ...........................................................5.40kg Size .................................... 10(25) in.(cm) Engine Type ................... Air-cooled 2-stroke gasoline Saw chain Type........................... OREGON 90SG39X Model .................................... Zenoah GZ25N Pich x Gauge .. 3/8x0.043 (9.53 x 1.0
ページ5に含まれる内容の要旨
PSZ2600 5. For safe operation 1. Read this manual carefully until you WORKING PLAN completely understand and follow 1. You should never use the product all safety and operating instructions. when under the influence of alcohol, 2. Keep this manual handy so that you when suffering from exhaustion or lack may refer to it later whenever any of sleep, when suffering from drowsi- questions arise. Also note, if you have ness as a result of having taken cold G any questions which cannot be an- medici
ページ6に含まれる内容の要旨
PSZ2600 5. For safe operation IMPORTANT 3. Never operate the pruner at an angle greater than 60° in order to reduce the risk of being struck by falling objects Remove any obstacle before beginning work. during operation. 4. If the unit starts to shake or vibrate, turn off the engine and check the 4. Inspect the entire unit for loose fasteners and fuel leakage. Make sure that the cut- whole unit. Do not use it until the trouble has been properly corrected. ting attachment is properly installe
ページ7に含まれる内容の要旨
PSZ2600 5. For safe operation HANDLING FUEL (1) With a basic understanding of kick- 1. The engine of the ZENOAH product is back you can reduce or eliminate the designed to run on a mixed fuel, which element of surprise. Sudden surprise contains highly flammable gasoline. contributes to accidents. Never store cans of fuel or refill the tank (2) Keep a good grip on the saw with both of the unit in any place where there is a hands, the right hand on the rear G boiler, stove, wood fire, electrical
ページ8に含まれる内容の要旨
PSZ2600 6. Set up MOUNTING ENGINE A standard package contains the items as shown below. 1. Push the drive shaft housing toward the clutch housing and rotate it by hand to check that the drive shaft is engaged with the gears. 2. Insert the drive shaft housing into the clutch housing until it bottoms, (1) Guide bar (2) Saw chain and align the positioning holes on the clutch housing and the shaft tube (3) Gase case (4) Sprocket and install the screw. When difficult to engage, twist the engine sligh
ページ9に含まれる内容の要旨
PSZ2600 6. Set up 7. Fuel and chain oil 4. Adjust the chain tension by turning the tensioner screw until ■ FUEL the tie straps just touch the bottom side of the bar rail. WARNING • Gasoline is very flammable. Avoid smoking or bringing any flame or sparks near fuel. Make sure G to stop the engine and allow it cool before refuel- B ing the unit. Select outdoor bare ground for fueling and move at least 3 m (10 ft) away from the fueling point before starting the engine. • The Zenoah engines are l
ページ10に含まれる内容の要旨
PSZ2600 7. Fuel and chain oil 8. Operation sary for the engine to last long. Be careful that, if the WARNING agitation is insufficient, there is an increased danger of early piston seizing due to abnormally lean mixture. The cutting head will start rotating upon the engine starts. 5. Put a clear indication on the outside of the container to avoid mixing up with gasoline or other containers. 1. Feed fuel into the fuel tank and tighten the cap securely. 6. Indicate the contents on outside of con
ページ11に含まれる内容の要旨
PSZ2600 8. Operation 6. While holding the unit firmly, pull out the starter rope quickly STOPPING ENGINE until engine fires. G B 1. Release the throttle lever and run the engine for half a minute. 2. Shift the ignition switch (a) to the STOP position. WARNING IMPORTANT The product is equipped with a centrifugal clutch mecha- nism, so the cutting attachment begins to rotate as soon as • Except for an emergency, avoid stopping the engine while the engine is started by putting the throttle into
ページ12に含まれる内容の要旨
PSZ2600 8. Operation Checking oil supply IMPORTANT After starting the engine, run the chain at medium speed and see if chain oil has scattered off, as shown in the figure. The oil flow adjusting screw must be pressed in slightly in order to turn. Failure to do so could damage the pump and screw. 3. With a screwdriver, push in on the oil flow rate adjusting screw and turn in the desired direction (there are three incremen- tal settings): (a) Clockwise-decrease lubrication (b) Counter clockwise-
ページ13に含まれる内容の要旨
PSZ2600 9. Maintenance Every Every Every 25 50 100 Before System/components Procedure Note hours hours hours use after after after fuel leaks, fuel spillage wipe out ✔ G fuel tank, air filter, fuel filter inspect/clean ✔✔ replace, if necessary B see ■ adjusting replace carburetor idle adjusting screw ✔ idling speed (p. 11) if necessary clean and readjust GAP: .025 in (0.6 ~ 0.7 mm) spark plug ✔ plug gap replace, if necessary cylinder fins, intake air cooling ven
ページ14に含まれる内容の要旨
PSZ2600 9. Maintenance SPARK ARRESTER 1. Remove the muffler, insert a screwdriver into the vent, and wipe • The muffler is equipped with a spark arrester to prevent red hot carbon away any carbon buildup. Wipe away any carbon buildup on the from flying out of the exhaust outlet. Periodically inspect and clean as muffler exhaust vent and cylinder exhaust port at the same time. necessary with a wire brush. In the State of California it is required by law (Section 4442 of the California Public Reso
ページ15に含まれる内容の要旨
PSZ2600 9. Maintenance SPROCKET After every cutter has been set, check the depth gauge and file Check for extensive wear, and replace it when the teeth are it to the proper level as illustrated. (MA7) worn over 0.3 mm. 0.3 mm G B (1) Sprocket SAW CHAIN 0.25" (0.65 mm) WARNING It is very important for smooth and safe operation to keep the cutters always sharp. (1) Appropriate gauge checker (2) Make the shoulder round Your cutters need to be sharpened when: (3) Depth gauge standard • Sawdust bec
ページ16に含まれる内容の要旨
PSZ2600 10. Storage 11. Disposal Aged fuel is one of major causes of engine starting failure. Before When disposing your machine, fuel or oil for the machine, storing the unit, empty the fuel tank and run the engine until it uses be sure to allow your local regulations. all the fuel left in the fuel line and the carburetor. Store the unit indoor taking necessary measures for rust prevention. 12. Troubleshooting guide Case 1. Starting failure CHECK PROBABLE CAUSES ACTION fuel tank → incorrect fue
