ページ1に含まれる内容の要旨
OPERATION MANUAL
STAY-LEVEL HANDLEBAR SERIES
MODELS
PS706016
PS706020
PS706026
PS706030
PS706036
PAVEMENT SAW
(DEUTZ BF3L2011 DIESEL ENGINE)
Revision #2 (06/02/08)
To find the latest revision of this
publication, visit our website at:
www.multiquip.com
THIS MANUAL MUST ACCOMPANY THE EQUIPMENT AT ALL TIMES.
P/N 37434
ページ2に含まれる内容の要旨
PROPOSITION 65 WARNING Engine exhaust and some of its constituents, and some dust created by power sanding, sawing, grinding, drillingandotherconstructionactivities contains chemicals known to the State of California to cause cancer, birth defects and other reproductive harm. Some examples of these chemicals are: Leadfromlead-basedpaints. Crystallinesilicafrombricks. Cementandothermasonryproducts. Arsenicandchromiumfromchemically treatedlumber. Your risk from these exposures varies, dependingonh
ページ3に含まれる内容の要旨
SILICOSIS/RESPIRATORY WARNINGS WARNING WARNING SILICOSIS WARNING RESPIRATORY HAZARDS Grinding/cutting/drillingofmasonry,concrete,metaland Grinding/cutting/drillingofmasonry,concrete,metaland othermaterialswithsilicaintheircompositionmaygive other materials can generate dust, mists and fumes off dust or mists containing crystalline silica. Silica is a containing chemicals known to cause serious or fatal basiccomponentofsand,quartz,brickclay,graniteand injury or illness, such as respiratory diseas
ページ4に含まれる内容の要旨
PS7060 MULTIQUIP SAW — TABLE OF CONTENTS Proposition 65 Warning ........................................... 2 Silicosis/Respiratory Warnings ................................ 3 Table of Contents .................................................... 4 Dimensions ............................................................. 5 Specifications .......................................................... 6 Engine Specifications .............................................. 7 Training Checklist ..........
ページ5に含まれる内容の要旨
PS7060 MULTIQUIP SAW — DIMENSIONS E C D A B Figure 1. Chassis & Dimensions - Sideview TABLE 1. CHASSIS & DIMENSIONS REFERENCE DIMENSIONS DESCRIPTION LETTER in. (mm) A Max Height (Front Pointer raised) 52-5/8 in. (1335 mm) B Max Handle Bar Height 33-3/8 in. (847 mm) C Max Length (Handle Bars Installed & Front Pointer fully raised) 77-1/4 in. (1962 mm) D Length (Handle Bars not Installed & Front Pointer fully raised) 57-1/8 in. (1450 mm) E Max Length (Handle Bars Installed & Front Pointer lowered)
ページ6に含まれる内容の要旨
PS7060 MULTIQUIP SAW — SPECIFICATIONS H G K F I J Figure 2. Chassis & Dimensions - Bottomview TABLE 2. BLADE AND SHAFT SPECIFICATIONS Blade Shaft Assembly Oil bath design, fully enclosed cast iron housing Blade Shaft Bearings Oil lubricated, no lubrication requirements Blade Shaft Diameter 2-3/8 in. (60mm) 1 in. (25.4 mm) Arbor Diameter Blade Flanges Quick disconnect system, inner flanges mounted to shaft 4-1/2 in.a6 nd in. (114mma2 nd 15 mm) Blade Flange Sizes Drive Belts 10 belts, (2) 5G 3VX-5
ページ7に含まれる内容の要旨
PS7060 MULTIQUIP SAW — ENGINE SPECIFICATIONS TABLE 3. ENGINE / MOTOR SPECIFICATIONS Engine Manufacture Deutz Model BF3L2011 Max RPM 3000 Horsepower / Max kW 60.2 / 44.9 Peak Torque 133.4 lb-ft. / 181 Nm Fuel Diesel Fuel Capacity 8.25 gallons / 31.2L Air Filter Dual element radial seal with integral turbo pre-cleaner Oil Capacity 8 quarts / 7.5L Engine Coolant Oil to Air TABLE 4. TRANSMISSION SYSTEM SPECIFICATIONS Transmission Pump Hydro-gear hydrostatic transmission pump Wheel Motors Hydro-gear
ページ8に含まれる内容の要旨
TRAINING CHECKLIST TRAINING CHECKLIST This checklist lists the minimum requirements for machine maintenance and operation. Please feel free to detach it and make copies. Use this checklist when training a new operator or use as a review for more experienced operators. TRAINING CHECKLIST NO. DESCRIPTION OK? DATE 1 Read Operator’s Manual completely. 2 Machine layout, location of components, checking of engine and hydraulic oil levels. 3 Fuel system, refueling procedure. 4 Operation of spray and
ページ9に含まれる内容の要旨
DAILY PRE-OPERATION CHECKLIST DAILY PRE-OPERATION CHECKLIST DAILY PRE-OPERATION CHECKLIST 1 Hardware and damage check. 2 Engine oil level. 3 Hydraulic oil level. 4 Condition of blade. 5 Safety Stop Switch operation. 6 Braking control operation. COMMENTS: PS7060 MULTIQUIP SAW � OPERATION MANUAL — REV. #2 (06/02/08) — PAGE 9
ページ10に含まれる内容の要旨
SAFETY MESSAGE ALERT SYMBOLS HAZARD SYMBOLS FOR YOUR SAFETY AND THE SAFETY OF OTHERS! Safety precautions should be followed at all times when operating this equipment. Failure to read, understand and Lethal Exhaust Gases comply with the Safety Messages and Operating Instructions could result in injury to yourself and others. Engine exhaust gases contain harmful toxins and will displace oxygen when running in an This Operation Manual has been enclosed or confined area. NEVER operate develope
ページ11に含まれる内容の要旨
SAFETY MESSAGE ALERT SYMBOLS Accidental Starting Respiratory Hazard Accidental starts can cause severe injury or death. ALWAYS place the ON/OFF switch in the OFF position. Disconnect negative battery cable from battery before servicing. ALWAYS wear approved respiratory protection. Sight and Hearing hazard Over Speed Conditions ALWAYS wear approved eye and hearing protection. NEVER tamper with the factory settings of the engine governor or settings. Personal injury and damage to the engine or
ページ12に含まれる内容の要旨
PS7060 MULTIQUIP SAW — RULES FOR SAFE OPERATION ■ NEVER operate this equipment when not feeling well due to RULES FOR SAFE OPERATION fatigue, illness or taking medicine. ■ NEVER operate the saw under the influence of drugs or alcohol. WARNING WARNING WARNING WARNING WARNING ■ AVOID wearing jewelry or loose fitting clothing that may snag Failure to follow instructions in this manual may lead to serious on the controls or moving parts, this can cause a serious injury or even death! This equipmen
ページ13に含まれる内容の要旨
PS7060 MULTIQUIP SAW — RULES FOR SAFE OPERATION ■ ALWAYS keep the work area well organized. ■ NEVER touch the hot exhaust manifold, muffler ■ Keep the saw clean. It will perform better and last longer. or cylinder. Allow these parts to cool before ■ ALWAYS Clear the cutting area of any debris, tools, etc. that servicing the saw. Contact with hot! would constitute a hazard while the saw is in operation. components can cause serious burns. WARNING WARNING WARNING WARNING WARNING DANGER DANGER DA
ページ14に含まれる内容の要旨
PS7060 MULTIQUIP SAW — RULES FOR SAFE OPERATION ■ Always store equipment properly when not being used. Diamond Blade Safety Equipment should be stored in a clean, dry location out of ■ Use appropriate steel-centered diamond blades the reach of children. When storing the saw in freezing manufactured for particular use on your saw. See further weather, blow out the water lines to prevent damage to blade information in this manual. components in the water delivery system. WARNING WARNING WARNING W
ページ15に含まれる内容の要旨
PS7060 MULTIQUIP SAW — RULES FOR SAFE OPERATION Saw Lifting and Loading Safety Towing Safety Precautions (Trailer Usage) CAUTION CAUTION CAUTION CAUTION CAUTION CAUTION CAUTION CAUTION CAUTION CAUTION Conform to Department of Transportation (DOT) Safety This Saw is very heavy. Use proper heavy lifting procedures Towing Regulations before transporting saw on public and DO NOT attempt to lift the by the guards. roads. To reduce the possibility of an accident while transporting the DANGER DANGER
ページ16に含まれる内容の要旨
PS7060 MULTIQUIP SAW — RULES FOR SAFE OPERATION Battery ■ ALWAYS allow the saw a proper amount of time to cool before servicing. The battery contains acids that can cause injury to the eyes and skin. To avoid eye irritation, always wear safety glasses or face ■ Prior to service, level the frame surface. shielding. Use well insulated gloves when picking the battery ■ Anytime the saw is lifted onto its nose, or tilted fully back such up. Use the following guidelines when handling the battery.
ページ17に含まれる内容の要旨
PS7060 MULTIQUIP SAW — INTENDED USE / FAMILIARIZATION Intended Use Features Operate the PS7060 MULTIQUIP SAW, tools and components ■ Stay-Level handlebar system adjusts handlebar angle in accordance with the manufacturer's instructions. Use of any automatically. other tools for stated operation is considered contrary to designated use. The risk of such use lies entirely with the user. ■ Engine Stop Switch conveniently located on Operators The manufacturer cannot be held liable for damages as a
ページ18に含まれる内容の要旨
NOTES PAGE 18 — PS7060 MULTIQUIP SAW � OPERATION MANUAL — REV. #2 (06/02/08)
ページ19に含まれる内容の要旨
PS7060 MULTIQUIP SAW — SERIAL TAG INFORMATION 1 2 MODEL SERIAL NO. Figure 4. Serial Tag/Locations Serial Tag The serial tag contains the model number and serial number of Record these numbers, in case you need to contact the the saw. The information details all parts that were included with manufacturer for information or service in the future. the saw when it was shipped from the factory, as well as the date Record your ENGINE model, (Item 2) specification number and of manufacture. serial nu
ページ20に含まれる内容の要旨
PS7060 MULTIQUIP SAW — CONTROLS AND INDICATORS 16 7 6 5 14 17 15 3 4 13 12 6 5 7 150 175 8 4 125 200 100 9 230 3 255 75 10 280 11 2 50 305 12 330 11 25 1 355 13 8 380 14 0 0 MM 15 INCH 9 2 1 10 18 Figure 5. PS7060 MULTIQUIP SAW Controls and Indicators Figures 5 and 6 show the location of the controls, indicators and 9. Depth Stop – Allows repeatable cutting depths. general maintenance parts. The function of each control, indicator 10. Left Water Flow Valve – Meters water supply. or maintenanc
