ページ1に含まれる内容の要旨
P3 / P3 EVOLUTION
®
Cod. 2850017 - Rev. 00 - Marzo 2009
ページ2に含まれる内容の要旨
TECHNICAL CHARACTERISTICS LEGEND F WATER FILTER VA ONE-WAY VALVE D ANTI-LIMESTONE FILTER (optional) CV FLOWMETER Dimensions: Height 62 cm P PUMP Width 42 cm V ONE-WAY VALVE Depth 40 cm C BOILER Ev1 TEA OR SOLUBLE COFFEE VALVE Weight: 35 Kg Ev2 MILK & CHOCOLATE VALVE Ev3 HOT WATER VALVE (OPTIONAL) EvE ESPRESSO COFFEE VALVE Voltage supply: 230 Vac. 50 Hz or 120 Vac. 60Hz on request GE ESPRESSO GROUP Absorbed power: 1,6 KW S WASTE Selections: 11 s
ページ3に含まれる内容の要旨
WATER FLOW DIAGRAM GRINDER The quantity of ground coffee is adjustable through a screw (2); screwing it the quantity decreases, while unscrewing it, the quantity increases.. To adjust the degree of grinding, after having pushed the lock (6), act on the grind-stone holder (1), clockwise to have a finer grinding, while in counterclock- wise to obtain a bigger grinding. Make sure that the lock comes back in the hole of block of the grind-stone holder, before starting the grinder.
ページ4に含まれる内容の要旨
LEGEND INSTALLATION A Main power B Main switch Before installing the machine, read carefully this manual. C “Anti-interference” filter Install the machine in a dry and hygienic place. D Transformer 230/24 Vac or 120/24 Vac E Coffee group heating elem. 24 Vac F Ventilator ELECTRIC CONNECTION G Safety clixon 145°C H Boiler heating element 1200 W IP “Door” safety switch S Boiler temperature sensor Before connecting the machine to an electric plug, please follow these pre
ページ5に含まれる内容の要旨
HYDRAULIC CONNECTION ELECTRICAL DIAGRAM The machine could be installed on: • a cabinet with place for cups, spoons and sugar and a water tank of 15lt • a small base with waste containers (the machine has to be with mains water connection). On cabinet Place the dispenser on the base and fix it with the screws. Fill up the special water tank with potable water, insert the tube with the filter and the one-way valve , and if it's present, the float. Insert in the tank of 5
ページ6に含まれる内容の要旨
SWITCHING ON TROUBLESHOOTING GUIDE The machine is provided with a program of self-diagnosis, that allows to visualize After having followed all the instructions of installation, it is possible to turn on on the display the messages of breakdown or machine stopped : the machine through the light switch situated on the frontal side of the electric panel. ERROR GROUP 1 the coffee-group has not reached the “supply position” given by its right At the switch on of the machine, it ap
ページ7に含まれる内容の要旨
QUICK FUNCTIONS PROGRAMMING In this section, it is possible to perform some of the most useful functions by the There are 2 levels of program: a frequent menu and a main menu. loader. The frequent menu is useful to the operator to regulate the dosing of the drinks, to To access press the button “QUICK MENU” of the keyboard (see page 6). set the prices, to notice the counters and to visualize the events of the machine. On display you will see “QUICK MENU ” The main menu is useful
ページ8に含まれる内容の要旨
Movements nr 20 and 21 (Decounter coffee and SET DRINKS chocolate) Entering the program through E, you will see the sequence of the existing drink codes. The movements nr20 (decounter coffee) and nr21 (decounter chocolate), where inserted, decrease the relative decounter by a unit. 01-02-03-04-05-0 To set the value of the decounter, it is enough to change it in one selection which Sel.1 contains it, automatically it will be modified also in all the other selections. The
ページ9に含まれる内容の要旨
It is possible to eliminate, to modify or to insert movements or to change its regu- To modify the name of the drink use the keys: lations where possible, for example the dosing of the products. " 7" to withdraw with the cursor on the character · to move the selection cursor movement use + and - " 6" to advance with the cursor on the character · to insert a new movement in the selected position press" 2" "+" or" -" to modify the character · to eliminate the selected movement press"
ページ10に含まれる内容の要旨
COUNTERS & AMOUNTS SET DRINKS In this menu it is possible to notice the counters of the various selections and Premise: every selection or drink it is composed from a sequence of movements eventually to reset them. which correspond to a single operation of the machine. The single movements are only performed after the correct event of the previous Press E to enter the menu that is composed in the following parameters: movement, in case of not-correct operation the machine will go to a
ページ11に含まれる内容の要旨
Electrical OUTPUT EVENTS In this menu it is possible to notice the last 100 events of the machine. Entering the menu with ENTER the following data will be visualized: N° description 1 Date : hour & date Not used ID:XXX RESULT POS 2 Grinder motor 3 Coffee releaser solenoid The time and the date of the event are not available. 4 Espresso unit motor ID indicates the kind of event, that can be a code drink or an internal operation of the ma
ページ12に含まれる内容の要旨
RESET COUNTERS&AMOUNTS: Reset of all the counters above. Press “6” MAIN MENU to confirm or “5” to cancel. To access this menu, keep pressed the button PROG for 5 seconds. ENABLE SLAVE MACHINE Enable the “slave” machine (not available). The menu is composed by the followings programs: ENABLE TEMPERAT.ON DISPLAY: Visualization on display of the boiler temperature. PAYMENT SYSTEM Setting of the system of payment and its options. SERIAL NUMBER: set the serial number of the
ページ13に含まれる内容の要旨
OPTIONS: LEVEL 2 (manager- technician) PAYMENT SYSTEM After having inserted the correct password, that it initially is" ask to manufac- The followings programs compose this menu: turer", you will enter in the following menu: SET COIN VALUE PARALLEL SYSTEM MODIFY PASSWORD LEVEL 1: Insert the new password and press E to con- Setting of the coin values (see note 1). firm. DECIMAL POINT MODIFY PASSWORD LEVEL 2: Insert the new password and press E to con- Setting of the decimal po
ページ14に含まれる内容の要旨
SET TEMPERATURE OPTIONS: LEVEL 1 (operator) The followings programs compose this menu: After having inserted the correct password, which initially is "ask to the manufac- turer”, the following menu will compare: SET BOILER 1 TEMPERATURE Set-up of the boiler 1 temperature. MODIFY PASSWORD LEVEL 1: Insert the new password and press E to con- firm. TIME OVERHEATING BOILER 1 After this time of “machine stopped” the boiler 1 is overheated. TEST MACHINE MODE: Set the machine in Test mo
