ページ1に含まれる内容の要旨
ACTiSYS Corp. Serial-IR Dongle Installation Manual
ACT-IR220L+/220L/200L
IrDA PC Adapter
User’s Manual
ACTiSYS Corp.
48511 Warm Springs Blvd, Suite 206
Fremont, CA 94539, USA
TEL: (510) 490-8024, FAX: (510) 623-7268
E-Mail: irda-support@actisys.com
Web: www.actisys.com
Release 1.5 1
ACTiSYS Corporation 2001 All Rights Reserved
ページ2に含まれる内容の要旨
ACTiSYS Corp. Serial-IR Dongle Installation Manual FCC & VCCI Compliance Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. WARNING-FCC Regulations state that any unauthorized changes or modifications to this equipment not expressly approved by the manuf
ページ3に含まれる内容の要旨
ACTiSYS Corp. Serial-IR Dongle Installation Manual CONTENTS CONTENTS............................................................................................................................................. 3 INTRODUCTION ..................................................................................................................................... 4 PACKING CHECK LIST..........................................................................................................
ページ4に含まれる内容の要旨
ACTiSYS Corp. Serial-IR Dongle Installation Manual INTRODUCTION This document provides instructions to install the ACT IR220L+/220L/200L Serial-IR dongle along with Windows 98/ME/2000 device driver. It is assumed that the user is familiar with basic operation of Window 98/ME/2000. PACKING LIST When you unpack the package, the following items should be found. 1. ACT-IR220Lplus or ACT-IR220L or ACT-IR200L. 2. User’s Guide SYSTEM REQUIREMENTS To use ACT-IR
ページ5に含まれる内容の要旨
ACTiSYS Corp. Serial-IR Dongle Installation Manual WINDOWS 98 INSTALLATION GUIDE Precaution: If you have not verified your Bios setup at this point, we strongly recommend you to refer back to the Bios verification section and verify your Bios setup again. Note: Verify that the Comport you will use to install ACT-IR220L/220L+/200L is not being already used or occupied by any hardware or any software. We recommend users to completely delete any files or drivers that can interrupt c
ページ6に含まれる内容の要旨
ACTiSYS Corp. Serial-IR Dongle Installation Manual 8. Select No, the device isn’t in the list in the Next box. Then click . 9. Highlight Infrared Devices from the Hardware types list, then click Next. 10. Click Next. Release 1.5 6 ACTiSYS Corporation 2001 All Rights Reserved
ページ7に含まれる内容の要旨
ACTiSYS Corp. Serial-IR Dongle Installation Manual 11. From Manufacturers list, choose (Infrared COM port or dongle), from Infrared Devices list, choose (Generic Infrared Serial Port or dongle). Then click OK. 12. Choose ACTiSYS IR-200L if you are a ACT-IR 200L user. Then click Next. 13. Choose ACTiSYS IR-220L/ 220L+ if you are a ACT-IR-220L/ ACT-IR220L+ User. Then click Next. Release 1.5 7 ACTiSYS Corporation 2001 All Rights Reserved
ページ8に含まれる内容の要旨
ACTiSYS Corp. Serial-IR Dongle Installation Manual 14. Select COM port which is physically connected to the Dongle. In most cases, the Dongle is connected to COM2. Choose Communication Port (COM2) from the Port list, click Next. 15. Reboot your computer. Release 1.5 8 ACTiSYS Corporation 2001 All Rights Reserved
ページ9に含まれる内容の要旨
ACTiSYS Corp. Serial-IR Dongle Installation Manual WINDOWS 98 UNINSTALLATION GUIDE 1. Boot up your computer system. 2. Click Control Panel. 3. Double click System Icon 4. Click Device Manager tab. 5. Highlight Infrared Communication Device, and then click Remove. 6. Click OK in the Confirm Device Removal box. Release 1.5 9 ACTiSYS Corporation 2001 All Rights Reserved
ページ10に含まれる内容の要旨
ACTiSYS Corp. Serial-IR Dongle Installation Manual 7. Highlight (Generic Infrared Serial Port or Dongle), then click Remove. 8. Click OK in the Confirm Device Removal. 9. Click on OK to restart your computer. Release 1.5 10 ACTiSYS Corporation 2001 All Rights Reserved
ページ11に含まれる内容の要旨
ACTiSYS Corp. Serial-IR Dongle Installation Manual WINDOWS 2000 INSTALLATION GUIDE Note: If you do not change your computer BIOS setting, STOP here and go to Chapter BIOS SETUP. Note: If your computer system has installed some device on the same com port before, you MUST NOT properly uninstall the devices first. ACT-IR220L+/220L/200L would work with your system any more if the devices are uninstalled improperly because some drivers are still there and cause conflicts with ACT-IR220
ページ12に含まれる内容の要旨
ACTiSYS Corp. Serial-IR Dongle Installation Manual 7. Highlight ADD a new drive then click Next. 8. Choose No, I want select the hardware form a list OK then click 9. Select the Infrared device from the Hardware types. Release 1.5 12 ACTiSYS Corporation 2001 All Rights Reserved
ページ13に含まれる内容の要旨
ACTiSYS Corp. Serial-IR Dongle Installation Manual 10. From Manufacturers list, choose ACTiSYS, from Infrared Device list, choose ACTiSYS IR-200L Serial Infrared Device for IR200L; click Next>. 11. Choose ACTiSYS IR-220L Serial Infrared Device for IR220L, click Next>. 12. ACTiSYS IR-220L+ Serial Infrared Device for Next> IR220L+, click . Release 1.5 13 ACTiSYS Corporation 2001 All Rights Reserved
ページ14に含まれる内容の要旨
ACTiSYS Corp. Serial-IR Dongle Installation Manual 13. Click Next>. 14. Choose COM2 in most case, then click Next>. 15. Click Finish. Release 1.5 14 ACTiSYS Corporation 2001 All Rights Reserved
ページ15に含まれる内容の要旨
ACTiSYS Corp. Serial-IR Dongle Installation Manual WINDOWS 2000 UNISTALLATION 1. Startup your computer system. 2. Click on Control Panel. 3. Double click System Icon. 4. Click on Hardware tab, then click Device Manager button. 5. Click on Infrared devices, then highlight ACTiSYS IR-220L+Serial Infrared Device. 6. Click Action and then Uninstall. Release 1.5 15 ACTiSYS Corporation 2001 All Rights Reserved
ページ16に含まれる内容の要旨
ACTiSYS Corp. Serial-IR Dongle Installation Manual 7. The device has been uninstalled and close device manager, restart your computer. Release 1.5 16 ACTiSYS Corporation 2001 All Rights Reserved
ページ17に含まれる内容の要旨
ACTiSYS Corp. Serial-IR Dongle Installation Manual WINDOWS ME INSTALLATION GUIDE Precaution : If you have not verified your Bios setup at this point, we strongly recommend you to refer back to the Bios verification section and verify your Bios setup again. Note: Verify that the Comport you will use to install ACT-IR220L/220L+/200L is not being already used or occupied by any hardware or any software. We recommend users to completely delete any files or drivers that can interrupt cl
ページ18に含まれる内容の要旨
ACTiSYS Corp. Serial-IR Dongle Installation Manual 8. Choose No I want to select the hardware from a list, then click Next>. 9. If you can not find Infrared device from Hardware types list, choose Other devices from the Hardware types list, then click Next >. Otherwise go to step 16. 10. From Manufacturers list, choose (legacy serial infrared device), from Models list, Choose ACT-IR200L Infrared Wireless Interface, then click Next>. 11. Click Finish. Release 1.5 18
ページ19に含まれる内容の要旨
ACTiSYS Corp. Serial-IR Dongle Installation Manual 12. Double click Add New Hardware icon. 13. Click Next>. 14. Click Next>. 15. Choose No I want select the hardware from list, then click Next>. Release 1.5 19 ACTiSYS Corporation 2001 All Rights Reserved
ページ20に含まれる内容の要旨
ACTiSYS Corp. Serial-IR Dongle Installation Manual 16. Highlight Infrared device from Hardware types list. Then click Next> 17. Click Next>. 18. Click Next> 19. If your device is IR200L, choose ACTiSYS IR200L, click Next>. Release 1.5 20 ACTiSYS Corporation 2001 All Rights Reserved
