ページ1に含まれる内容の要旨
Quick Guide
Quick Guide
POS50 Series
POS50 Series
A Ap pr riill.. 2 20 00 06 6 ( (V V1 1..0 0) )
1
ページ2に含まれる内容の要旨
CONTENTS CONTENTS Chapter 1 Unpacking -------------------------------------------------------------------------------- 3 Chapter 2 Specification -------------------------------------------------------------------------------- 4 2.1 Specification 2.2 I/O Ports Chapter 3 Installation --------------------------------------------------------------------------------- 6 3.1 OS Installation
ページ3に含まれる内容の要旨
Chapter 1 Unpacking Unpacking the POS Terminal, please check the following items are presented and in good conditions: a. Main Unit b. CD: User’s Manual & Driver Bank The driver disk includes user’s manual and all of driver software of peripheral, such as touch screen, VGA, LAN….etc. c. Power Cord: Optional USA, Europe, UK or Australia type. 3
ページ4に含まれる内容の要旨
Chapter 2 Specification 2.1 Specification The POS system configuration including 8.4”, 12.1” and 15” as followings, Main Board CPU AMD Geode LX-800 System Memory 1 x DDR400 SO-DIMM Socket, up to 1GB Display TFT LCD Size 8.4” 12.1” 15” 180nits 300nits 250nits Brightness Resolution 800x600 1024x768 Touch Screen 5 Wire Resistive Type Storage Device No Support HDD 2.5” Slim Type Compact Flash 1 x Type II, Slot I/O Ports Serial 2x RS232 (Pin9 wit
ページ5に含まれる内容の要旨
2.2 I/O ports Following ports show all of ports of system. a. DC IN: connector for power adapter input 12VDC. b. Cash Drawer: provide IO port address 280H for cash drawer control by RJ11. c. COM 1/2: standard D sub serial port with 5V / 12VDC selected on pin9. d. LAN: 10 / 100 base-T by RJ45 connector. e. USB: play and plug USB 2.0. f. Power Switch: toggle switch for power on. g. MSR PS2: for attached MSR PS2 interface connection.
ページ6に含まれる内容の要旨
Chapter 3 Installation 3.1 OS Installation 3.1.1 Embedded WEPOS / WinCE CD ROM Driver with USB interface If you bought the system including WEPOS / WinCE operation system, please follow up below procedure. a. Connect CDROM to the USB port of system. b. Turn on the system and enter completely into WEPOS. c. Up load your application software into WEPOS platform. d. Complete installation and execute the AP. Note: We suggest that
ページ7に含まれる内容の要旨
d. Select “First Boot Device” to “USB-CDROM”. e. Press “F10” to save setup change and quit. f. Install the Win XP, follow up the OS installation guide. Phoenix – Award BIOS CMOS Setup Utility Advanced BIOS Features Virus Warning [Disabled] CPU Internal Cache [Enabled] Boot From Lan Control [Disabled] First Boot Device [USB-CDROM] Second Boot Device [HDD-0] Third Boot Device [CDROM]
ページ8に含まれる内容の要旨
8
ページ9に含まれる内容の要旨
9
ページ10に含まれる内容の要旨
10
ページ11に含まれる内容の要旨
11
ページ12に含まれる内容の要旨
3.3 MSR / I-Button PS2 interface Installation a. The MSR Kit included Bracket and Module. b. Turn the system to rear side. c. Screw up the bracket on the fixed hole. 12
ページ13に含まれる内容の要旨
d. Screw up the MSR module and connect the cable into connector. 3 3..4 4 C Ca as sh h D Dr ra aw we er r rd For the 3 version M/B which is released from end of April. The cash drawer pin assignment as followings. In order to program the cash drawer easily, we also provide OPOS driver.
ページ14に含まれる内容の要旨
Chapter 4 Jumper Definition 4.1 Main Board Layout 14
ページ15に含まれる内容の要旨
4.2 LCD Power setting • JP2: This jumper is for the setting of LCD panel voltage. JP2 Description 2-4 +3.3V 4-6 +5V • JP2: This jumper is for the setting of LCD panel shift clock. JP2 Description 1-3 Inverted 3-5 Normal 4.3 COM1/2 Power Selection JP3 Description 1-3 COM1 RI Pin Use +12V 3-5 COM1 RI Pin Use +5V 7-9 COM1 RI Pin Use RI 2-4 COM2 RI Pin Use +12V 4-6 COM2 RI Pin Use +5V 8-10 COM2 RI Pin Use RI 4.4 COM3 Power Selection JP4 Description 1-2 COM3 RI P
ページ16に含まれる内容の要旨
33 SA1 34 CABLE_80P 35 SA0 36 SA2 37 HDC CS0# 38 HDC CS1# 39 HDD ACTIVE# 40 GROUND 41 VCC5 42 VCC5 43 GND 44 b. CN8: Compact Flash Storage Card Socket PIN Description PIN Description 1 GROUND 26 CARD DETECT1 2 D3 27 D11 3 D4 28 D12 4 D5 29 D13 5 D6 30 D14 6 D7 31 D15 7 CS1# 32 CS3# 8 N/C 33 N/C 9 GROUND 34 IOR# 10 N/C 35 IOW# 11 N/C 36 OBLIGATORY TO PULL HIGH 12 N/C 37 IRQ15 13 VCC 38 VCC 14 N/C 39 SLAVE 15 N/C 40 N/C 16 N/C 41 RESET# 17 N/C 42 IORDY 18 A2 43 DRQ 1
ページ17に含まれる内容の要旨
4.7 Serial Ports The system provides three high speed NS16C550 compatible UARTS with Read/Receive 16 byte FIFO. Four com ports are in IO connector. • COM1: CN25 DB9-pin header • COM2: CN26 DB9-pin header PIN Description DATA CARRIER DETECT (DCD) 1 RECEIVE DATA (RXD) 2 TRANSMIT DATA (TXD) 3 DATA TERMINAL READY (DTR) 4 5 GROUND 6 DATA SET READY (DSR) REQUEST TO SEND (RTS) 7 CLEAR TO SEND (CTS) 8 9 RING INDICATOR (RI) • COM2: CN27 pin header 2.0mm PIN Description D
ページ18に含まれる内容の要旨
• CN21: Power Connector Input PIN Description PIN Description 1 GND 3 Power IN(+12V) 2 GND 4 Power IN(+12V) • CN28: Power Connector Output PIN Description PIN Description 1 +5V 3 GND 2 GND 4 +12V 4.9 VGA Connector The pin assignments are as following. • CN3: 10-pin Connector PIN Description PIN Description 1 RED 2 DDCDAT 3 GREEN 4 DDCCLK 5 BLUE 6 GROUND 7 HSYNC 8 GROUND 9 VSYNC 10 GROUND 4.10 LCD & INVERTOR Connector The pin assignments are as following. CN2: 15
ページ19に含まれる内容の要旨
3 GROUND 4 N/C 5 +12V 6 GROUND 4.11 USB Port Connector • USB1: CN22 • USB2: CN23 • USB3: CN31 • USB4: CN15 PIN Description 1 +5V 2 DATA- 3 DATA+ 4 GROUND 4.12 Audio Connector The pin assignments are as following. • CN17: LINE_OUT connector PIN Description 1 LINE_OUT_L 2,3 LINE_OUT_GROUND 4 LINE_OUT_R • CN16: MIC_IN connector PIN Description 1 MIC_IN 2 GROUND 4.13 LED The pin assignments are as following. • CN6: LED connector PIN Description P
ページ20に含まれる内容の要旨
PIN Description 1 Reset button + 2 Reset button - 4.15 Cash Drawer Connector • CN20 PIN DESCRIPTION PIN DESCRIPTION 1 GROUND 2 DOUT_0 3 DIN_0 4 +12V 5 N.C 6 GROUND 4.16 Keyboard / Mouse connector • CN19: Keyboard/Mouse Connector PIN DESCRIPTION 1 VCC5 2 MOUSE DATA 3 MOUSE CLK 4 KEYBOARD DATA 5 KEYBOARD CLK 6 GROUND 4.17 Touch Connector The pin assignments are as following. • CN29: Touch 5W connector PIN DESCRIPTION 1 RT 2 RL 3 SG 4 LT 5 LL • CN30 :
