ページ1に含まれる内容の要旨
User’s Manual
Single Board Computer 3301630
Version 1.0, April 2005
ページ2に含まれる内容の要旨
Copyrights This manual is copyrighted and all rights are reserved. It does not allow any non authorization in copied, photocopied, translated or reproduced to any electronic or machine readable form in whole or in part without prior written consent from the manufacturer. In general, the manufacturer will not be liable for any direct, indirect, special, incidental or consequential damages arising from the use of inability to use the product or documentation, even if advised of the poss
ページ3に含まれる内容の要旨
3301630 User’s Manual Packing List: Please check the package content before you starting using the board. Hardware: 3301630 motherboard x 1 Cable Kit: 44-pin 40-pin 44-pin ATA33 IDE Cable x1 Floppy Cable x 1 SATA Cable x 2 SDTV Cable x 1 Parallel cable x 1 YPbPr Cable x 1 COM port Cable x 2 DVI-I Y cable x 1 PS/2 Keybroad & Mouse cable x 1 CPU Cooler x 1 Dual USB cable with bracket x 1 Audio cable with bracket x 1 Printed Matters: User’s Manual x 1 Driver CD x 1 3
ページ4に含まれる内容の要旨
3301630 User’s Manual Index Chapter 1 ....... ....... ....... ....... ....... ....... ....... ....... ....... ....... ...... 7 1.1 .......................................................................... 7 1.2 ..................................................................... 8 1.3 .................................................................... 10 1.4 ........ ........ ........ ........ .....
ページ5に含まれる内容の要旨
3301630 User’s Manual 3.1
ページ6に含まれる内容の要旨
3301630 User’s Manual (This Page is Left for Blank) 6
ページ7に含まれる内容の要旨
3301630 User’s Manual Introduction Chapter 1 1.1 3301630 is the new generation of the Half-size PCI CPU card, with supporting last Intel Pentium M processors for 533MHz front side bus, Intel 915GM and ICH6-M chipset, integrated GMA900 graphics, DDR2 memory, REALTEK AC97 Audio, Serial ATA, mini PCI and dual Gigabit LAN. New Intel Pentium M Processor The board supports last Intel Pentium M processors with 533MHz front side
ページ8に含まれる内容の要旨
3301630 User’s Manual Introduction 1.2 General Specification Form Factor Half-size PCI CPU card CPU Intel® Pentium M (Does not support Celeron M 4xx series processors) Package type: FC-PGA478 L2 Cache: 512KB/1MB/2MB Front side bus: 400/533MHz Memory 2 x 240-pin DDR2 400/533MHz SDRAM up to 2GB Up to 8GB/s of bandwidth with dual-channel interleaved mode Dual-Channel technology supported Unbufferred, none-ECC memory supported only Ch
ページ9に含まれる内容の要旨
3301630 User’s Manual Introduction Ethernet Interface Controller Marvell 88E8053 PCI Express Gigabit Ethernet controller Type Triple speed 10/100/1000Base-T auto-switching Fast Ethernet Full duplex, IEEE802.3U compliant Connector Dual External RJ45 connectors with LED on rear I/O panel Audio Interface Chipset Intel® ICH6M with Realtek® ALC201A codec Interface 2 channels Connector Onboard Audio connector for Line-out, Line-in, MIC-in Onboard CD-IN connect
ページ10に含まれる内容の要旨
3301630 User’s Manual Introduction 1.3 10 Mechanical Drawing
ページ11に含まれる内容の要旨
3301630 User’s Manual Introduction 1.4 Intel Pentium M/Celeron M Processors Intel GMA900 Graphics LVDS 2 x 240-pin DDR2 DVI SDVO 400/533MHz up to 915GM 2GB HDTV CompactFlash 2 x Serial ATA ports UltraDMA33/66/100 IDE 2 x USB2.0 ports ICH6-M PCIE PICMG Marvell E8053 Gigabit LAN ALC201A Mini-PCI slot 2 x Serial ports 2 x Serial ports BIOS 1 x Floppy ports 1 x Parallel Port IrDA 8-bit GPIO Block Diagram 11
ページ12に含まれる内容の要旨
3301630 User’s Manual (This Page is Left for Blank) 12
ページ13に含まれる内容の要旨
3301630 User’s Manual Hardware Setup Chapter 2 2.1 IDE Floppy CN_USB COM12 COM34 CN_ LPT CN IR CN_DIO SYSFAN CPUFAN JCSEL1 JCSEL2 CN_AUDIO DVI CN_VGA RJ45_A RJ45_B PS2 CN_ATKB JCFSEL SATA JVLCD2 CN_INV CN_TV CPUFAN CN_PWR CN_LVDS2 JFRNT CN_PS Connector Location 13
ページ14に含まれる内容の要旨
3301630 User’s Manual CF 14
ページ15に含まれる内容の要旨
3301630 User’s Manual Hardware Setup 2.2 Jumper Function JRTC CMOS Operating/Clear Setting JCFSEL CF with IDE mode selection JVLCD Panel Voltage Setting JCSEL1 Choose RS232/485/422 JCSEL2 Choose RS232/485/422 JRTC JCFSEL JVLCD2 Jumper Function JCSEL1 JCSEL1 1-2 short RS-232 JCSEL1 3-4 short RS-485 JCSEL1 5-6 short RS-422 JCSEL2 RS-232 JCSEL2 JCSEL2 RS-485/422 RS232 RS485 RS422 Connector Location 15
ページ16に含まれる内容の要旨
3301630 User’s Manual Hardware Setup 2.3 2.3.1 Connector Function Remark CPU Socket479 for CPU Standard DDRIIA/B 240 -pin DDR2 SDRAM DIMM socket Standard IDE 44-pin IDE connector Silm FDD 34-pin slim type floppy connector Standard SATA1/2 7-pin Serial ATA connector Standard CN_AUDIO 5 x 2-pin audio connector Standard CDIN 4-pin CD-ROM audio input connector Standard CN_DIO 6 x 2-pin digital I/O connector Standard C
ページ17に含まれる内容の要旨
3301630 User’s Manual Hardware Setup 2.4 2.4.1 The board comes with the socket479 for Intel Pentium M/Celeron M processors, it supports new generation of Intel Pentium M processors with 533MHz of front side bus and 2MB L2 cache. Please follow the instruction to install the CPU properly. Check point Unlock way 1. Use the flat-type screw drive to unlock the CPU socket 2. Follow the pin direction to install the processor on t
ページ18に含まれる内容の要旨
3301630 User’s Manual Hardware Setup 2.4.2 The board provides two 240-pin DDR2 DIMMs to support DDR2 400/533 memory modules up to 2GB of capacity. Non-ECC, unbuffered memory is supported only. While applying two same modules, dual channel technology is enabled automatically for higher performance. DDRIIB/A Please check the pin number to match the socket side well before installing memory module. 18 Memory Setup
ページ19に含まれる内容の要旨
3301630 User’s Manual Hardware Setup 2.5 The board’s data of CMOS can be setting in BIOS. If the board refuses to boot due to inappropriate CMOS settings, here is how to proceed to clear (reset) the CMOS to its default values. Jumper: JRTC Type: Onboard 3-pin jumper JRTC Mode 1-2 Clear CMOS 2-3 Normal Operation Default setting JRTC 1 3 CMOS Setup 19
ページ20に含まれる内容の要旨
3301630 User’s Manual Hardware Setup 2.6 The board has one UltraDMA33 IDE interface to support up to 2 ATAPI devices, and one CompactFlash Type II socket on the solder side, with jumper JCFSEL for IDE master/slave mode selection. Jumper: JCFSEL Type: onboard 3-pin header JCFSEL Mode 1-2 Master 2-3 Slave Default setting 1 3 JCFSEL 2.7 Based on Intel ICH6-M, the board provides two Serial ATA interfaces wit
