ページ1に含まれる内容の要旨
AIR CONDITIONER
Use & Care Guide
For questions about features, operation/performance, parts,
accessories or service call: 1-800-253-1301
Table of Contents ................................................ 2
1188226B
ページ2に含まれる内容の要旨
TABLE OF CONTENTS AIR CONDITIONER SAFETY .........................................................2 Starting Your Air Conditioner—Digital Control ..........................15 Starting Your Air Conditioner—Rotary Control..........................18 INSTALLATION REQUIREMENTS ................................................3 Changing Air Direction ...............................................................19 Tools and Parts .......................................................................
ページ3に含まれる内容の要旨
INSTALLATION REQUIREMENTS ® SMART-MOUNT tray assembly installation Tools and Parts Gather the required tools and parts before starting installation. A Read and follow the instructions provided with any tools listed here. B C Tools needed Flat-blade and Phillips Pencil screwdrivers Tape measure D ¹⁄₄" nut driver Level ⁷⁄₁₆" wrench Drill Scissors ³⁄₃₂" or smaller drill bit E G H I Through-the-Wall Installation F J In addition to the tools listed above, the following tools are
ページ4に含まれる内容の要旨
Window Installation Electrical Requirements Window opening measurements: 27" (68.6 cm) minimum to 40" (101.6 cm) maximum opening WARNING width. 19" (48.3 cm) minimum opening height. Electrical Shock Hazard Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter. A B Do not use an extension cord. Failure to follow these instructions can result in death, fire, or electrical shock. A. 27" (68.6 cm) minimum, 40" (101.6 cm) maximum The electrical ratings for your
ページ5に含まれる内容の要旨
RESET TEST Power Supply Cord INSTALLATION INSTRUCTIONS NOTE: Your unit’s device may differ from the one shown. A Unpack the Air Conditioner B WARNING Excessive Weight Hazard Use two or more people to move and install air conditioner. Failure to do so can result in back or other injury. A. Test button B. Reset button Remove packaging materials This room air conditioner is equipped with a power supply cord Remove and properly dispose of packaging materials. required by UL. This power supply
ページ6に含まれる内容の要旨
Window Installation 1. Using the tray back as a template, center in windowsill 1. To assemble the tray frame, insert tab on tray back into slot against outside edge of stool. on tray side. Check to see that the tab is engaged and the 2 pieces are aligned. Insert 2 - #8 - 18 x ¹⁄₄" hex-head screws to secure. 2. Repeat with other tray side. C C B B A A A. Tray back B. Windowsill C. Outside edge of stool A. Tray back 2. Using the 2 inside screw holes in tray back, mark B. #8 - 18 x ¹⁄₄" hex-he
ページ7に含まれる内容の要旨
2. Insert carriage bolt up through slot on tray-frame side and ® support leg. Install SMART-MOUNT Tray Assembly in Window ® 1. From inside, place SMART-MOUNT tray, support legs facing down, in the window. Match the holes in tray side with the predrilled holes in windowsill. 2. Using 2 - #10 - 12 x 1¹⁄₂" slot-head wood screws, secure the tray frame to the window. A 3. Place one end of tray center over carriage bolt. A. #10 - 12 x 1¹⁄₂" slot-head wood screws NOTE: If the exterior of building
ページ8に含まれる内容の要旨
Prepare Air Conditioner for Window Installation Top View Install Side Curtains NOTE: Attach curtains to unit before placing unit in window. 1. Insert curtain into curtain frame. Make sure curtain end locks into curtain frame. Top View Bottom View Side View 5. Extend right-hand curtain outward so you may insert the first screw through the middle hole of the curtain. Using a #8 x ³⁄₈" pan-head screw, screw curtain to middle hole in air 2. Push curtain in all the way. conditioner cabinet. 3.
ページ9に含まれる内容の要旨
Position the Air Conditioner in Window Handle air conditioner gently. Incorrect Installation Be sure your air conditioner does not fall out of the opening A B during installation or removal. Do not block the louvers on the front panel. B Do not block the louvers on the outside of the air conditioner. C WARNING Excessive Weight Hazard Use two or more people to move and install A. Window sash air conditioner. B. Top channel Failure to do so can result in back or other injury. C. Air con
ページ10に含まれる内容の要旨
Top View WARNING B A C Electrical Shock Hazard A. Side curtain against window channel Plug into a grounded 3 prong outlet. B. Window channel C. #8 x ³⁄₄" round-head screw Do not remove ground prong. Do not use an adapter. Complete Installation Do not use an extension cord. 1. Insert foam seal behind the top of the lower window sash and Failure to follow these instructions can result in death, against the glass of the upper window. fire, or electrical shock. A 4. Attach window-lock bracket to
ページ11に含まれる内容の要旨
Install Wood Frame A 1. Construct wood frame. See “Location Requirements” for dimensions. 2. Measure outside width and height of frame to determine wall opening dimensions. 3. Cut opening through the wall. Remove and save insulation. B NOTES: Dimension for depth depends on wall thickness and type of molding. Do not block louvers in air conditioner cabinet. Use 1" (2.5 cm) or thicker lumber for wood frame. A. Inside screw holes B. Indoor side of wall opening A 9. Remove the tray back.
ページ12に含まれる内容の要旨
4. Then place flat washer, lock washer and hex nut. Attach Support Legs NOTE: Do not tighten. The leg must be able to move freely to adjust angle when installed. 1. Determine the correct slots on the tray side from the type of exterior construction of the building. A B Thin wall construction (vinyl, wood, etc.) C D A E A. Hex nut D. Tray center B. Lock washer E. Carriage bolt C. Flat washer A. First and second slots 5. Insert second carriage bolt through tray side and attach other end of
ページ13に含まれる内容の要旨
2. Using 2 - #10 - 12 x 1¹⁄₂" slot-head wood screws, secure the A B tray-frame assembly to the wall opening. Left Side A. Angled edge on top of the tray side B. Notch ® 4. Adjust SMART-MOUNT tray until bubble indicates the angled edge on top of the tray side is level. A IMPORTANT: The tray must slope downward slightly toward A. #10 - 12 x 1¹⁄₂" slot-head wood screw the outside to provide proper drainage for the air conditioner. Right Side A B A A. Bubble indicates the angled edge on top of th
ページ14に含まれる内容の要旨
2. If the feet on the bottom of the air conditioner do not rest on and adjust angle of tray until air conditioner sits against the the wood strip, remove the air conditioner and adjust the bottom of the tray. ® SMART-MOUNT tray until feet rest on the wood strip. IMPORTANT: The tray must slope downward slightly toward the outside to provide proper drainage for the air conditioner. A A B B C A. Air conditioner ® A. Air conditioner sitting on SMART-MOUNT tray B. Feet on bottom of air conditione
ページ15に含まれる内容の要旨
AIR CONDITIONER USE Operating your air conditioner properly helps you to obtain the best possible results. Do not try to operate your air conditioner in the cooling mode This section explains proper air conditioner operation. when outside temperature is below 65°F (18°C). The inside evaporator coil will freeze up, and the air conditioner will not IMPORTANT: operate properly. If you turn off the air conditioner, wait at least 3 minutes NOTE: In the event of a power failure, your air co
ページ16に含まれる内容の要旨
To set the Timer to turn on the air conditioner, keeping Temperature previous settings: 1. Turn off air conditioner. Press the plus button to raise the temperature. Room 2. Press TIMER. Timer indicator light will flash. Hour indicator indicator light will turn off, and Set indicator light will turn on. light will turn on, and display will show remaining hours Display shows the Temperature control setting. Each time you before air conditioner will turn on. press or hold the plus button,
ページ17に含まれる内容の要旨
To raise the temperature: To Operate Air Conditioner with Remote Control Press the plus button. Room indicator light on air conditioner will turn off, and Set indicator light on air conditioner will turn on. NOTE: Remote control may vary in appearance. Display on air conditioner shows the Temperature control setting. Each time you press or hold the plus button, the temperature will increase 1º until it reaches 86°F (30ºC). NOTE: After 3 seconds, Set indicator light on air conditioner will
ページ18に含まれる内容の要旨
To set Timer to turn on air conditioner, changing the 6. Press TIMER. Timer indicator light on air conditioner will flash. Hour indicator light on air conditioner will turn on, and previous settings: display on air conditioner will show remaining hours before air 1. Turn on air conditioner. conditioner will turn on. 2. Adjust Mode to Auto Cool, Cool, Fan Only, or Power Saver. 7. Press the plus or minus button to change delay time (1 to NOTE: For Auto Cool mode, go to Step 4. 24 hours). 3. Fo
ページ19に含まれる内容の要旨
Models Without Power Saver Changing Air Direction Roll the wheel to direct the air right or left. Rotate the whole cartridge to direct air up, down or straight ahead. A Models With Power Saver A. Wheel A A. Cartridge Temperature Normal Sounds Turn the TEMPERATURE control to a mid-setting. Adjust the air conditioner's performance by turning the Temperature control When your air conditioner is operating normally, you may hear clockwise for maximum cooling. For less cooling, turn the sounds su
ページ20に含まれる内容の要旨
AIR CONDITIONER CARE Your new air conditioner is designed to give you many years of 3. Use a vacuum cleaner to clean air filter. If air filter is very dirty, dependable service. This section tells you how to clean and care wash it in warm water with a mild detergent. Do not wash air for your air conditioner properly. Call your local authorized dealer filter in the dishwasher or use any chemical cleaners. Air dry for an annual checkup. Remember… the cost of this service call filter completely
